Xip -B01 PANTHER User manual

Mini IR Bullet Camera IP XIP - B01 PANTHER
12
The Quick Guide is for quick installing and connecting the Full HD Multiple Stream Micro Bullet IP Camera XIP-B01
PANTHER. For details, please refer to the User’s Manual of the IP Camera.
Camera’s Connectors (Indoor Only)
Rear Panel 1
Rear Panel 2
No.
Connector
Definition
1
PoE NETWORK
For Ethernet cable and PSE connection
2
Network LEDs
Network connection and activity indication
3
Alarm I/O
1
Input −
3
Output −
2
Input +
4
Output +
4
Power Jack
DC 12V connector for power connection
5
LINE IN & LINE OUT
Two-way audio transmission
6
VIDEO (BNC Connector)
For analog videos output
MicroSD Card Slot / Default Button (Indoor and Outdoor Models)
The position of the microSD Card Slot and the Default Button are shown as below.
MicroSD Card Slot
Insert the SD Card in the microSD Card Slot to store videos and snapshots.
Default Button
Press the button with a proper tool for at least 20 seconds to restore the system.
IP Camera Installation
Please follow the instructions below to complete IP Camera installation.
Power up the Camera
To power up the IP Camera, please plug the camera’s DC 12V cable into the power terminal block. Alternatively,
connect the Ethernet cable to the camera’s RJ-45 port and plug the other end of the cable into a PoE switch.
NOTE: If PoE is used, make sure Power Sourcing Equipment (PSE) is in use in the network.
Ethernet Cable Connection
Connect one end of theCAT5 Ethernet cable to the RJ-45 connector of the IP Camera, and the other end of the cable
to the network switch or PC.
NOTE: In some cases, Ethernet Crossover cable might be needed when connecting the IP Camera directly
to the PC.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Green Link Light indicates good network connection.
OrangeActivity Light flashes for network activity indication.
Function Cables (Outdoor Only)
RJ-45 Cable
RJ-45 & DC 12V Cable
No.
Connector
Definition
1
RJ-45
For Ethernet cable and PSE connection
2
Power Jack
DC 12V connector for power connection
Before Login to the IP Camera
A client program will be automatically installed on the PC when connecting to the IPCamera. Before logging in to the
IP Camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual of the IP
Camera.
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
“Internet”, and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins”items to
<Prompt> or <Enable>.
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
“Internet”.
Step 4: Down the page, click “Default Level”and click
on <OK> to confirm the setting. Close the
browser window, and open a new one later for
accessing the IP Camera.

3
IP Camera Login
The IP Camera’s default IP address is: 192.168.0.250. Therefore, to access the IP Camera for the first time, set the
PC’s IP address as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID and Password
Key in the IP Camera’s IP address in the URL bar of the Web browser window and click on <Enter>.
Enter the default user name (Admin) and password (1234) in the prompt request dialogue. Note that user name is
case sensitive.
Install the ActiveX Control
After connecting to the IP Camera, the request for installing the ActiveX control will appear just below the URL bar.
Right click on the information bar, and then click on “Install ActiveX Control…” to permitActiveX control installation.
In the pop-up security warning window, click on <Install> to start downloading DC Viewer software on the PC.
Click on <Finish> after DC Viewer installation is complete.
Browser-based Viewer
The main page of the IP Camera user interface is shown as the figure below. Please note that function buttons will
vary depending on the camera model.
Mini Bullet IR IP Camera
XIP-B01 PANTHER
Quick Guide
Ver. 1.2