Xpresskit XK09 User manual

Vehicle Compatibility Chart
Wiring Diagram.
.........................................................................................................................................
Installation Procedure Overview..................................................................................................................................
...........................................................................................................................................................
Vehicle Type Programming.........................................................................................................................................
Vehicle Type Chart......................................................................................................................................................
User Configuration - Optional Programming...............................................................................................................
Tech Notes for Violet/White Wire.................................................................................................................................
LED Diagnostics.........................................................................................................................................................
02
03
04
05
05
06
07
07
Warranty...................................................................................................................................................................... 08
Index
TECHNICAL SUPPORT / INFORMATION
web resources:
www.xpresskit.com
www.xpressvip.com
www.directechs.com
† Chrysler and Dodge are registered trademarks and property of their respective companies.
Door lock and alarm module that interfaces directly with Chrysler and Dodge vehicles to provide features compatible with
door locks, driver and passenger sliding doors (open/close), factory alarms, trunk/hatch release, and door pin status
output for aftermarket alarm triggers.
Installation Guide
Downloadable Firmware for Platform XK09:
DLPKGM, DLGM5X, CHRYSLER, PLXR, PKN3, DLVW1, DLHO4, DLHO5, DLHY,
DLKIA1, DLKIA2, DLCH2, DLCH3, DLCH4.
Upgradable Door Lock & Alarm Interface
Platform: XK09
Firmware: DLCH3
DL
doorlock
INTERFACE
Update Alert
Firmware updates are posted to the web on a regular basis. We
recommend that you check for firmware and/or install guide updates
prior to installing this product.
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

Vehicle Compatibility Chart Page 2
To see a list of available features for each vehicle, visit www.xpresskit.com.
Vehicle Application Guide
2005 2004 2003 2002 2001 2000
Chrysler
PT Cruiser X X X X X
Dodge
Dakota X X X X
Durango X X X
Neon X X X X X X
RAM X X X X X
RAM SRT-10 X
SX X X
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

Please Note:
Failure to proceed in the following order could result in possible vehicle damage.
If your remote start system has D2D Jumpers, make sure both Jumpers are in the horizontal operating position.
Installation Procedure Overview
4
3
2
See details on page 5.
Module programming
Power up the XK09
Once done, the interface red LED will turn ON.
If connected in W2W
Connect the 20-pin harness.
If connected in D2D
Connect the 4-pin D2D harness first,
then connect the 20-pin harness.
Caution! The 20-pin connector can be easily plugged in backwards.
1
Make the necessary connections in the vehicle, as instructed in the
vehicle-specific guides.
Connect the remote starter to the vehicle
Make all the connections as per the provided wiring schematics,
either in W2W or D2D.
Wiring
Page 3
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

Programming
button
XK09 Front Side
Wiring Diagram Page 4
XK09 Back Side
10
01
20
11
20 PIN connector
wire side view
Blue/White
Red/White
Light Green
Blue
(-) Ground When
Running (Status)*
(-) Trunk*
(-) Lock*
(-) Unlock*
(+) 12 Volt*
(-) Ground*
Black
Red
+12VDC
XKLOADER2
Option A - Firmware Upgrades
Use with D2D harness XKD2D65.
Internet
USB CABLE
USB PORT
Option B - Data to Data Connection to RCS Data Port
Use with D2D harness HARD2D Rev. 3.
XL202**
XL202
Antenna
D2D connector
wire side view
(+) 12 Volt
RX
(-) Ground
TX
4 PIN connector
wire side view
01
04
Gray
Green (-) Trunk Detection Output*
(-) Door Detection Output*
* These wires are not required in D2D.
** Sold separately.
GreenJ1850 BUS
1 8
169
Diagnostic connector
(Face view)
Under dash driver side
Position 2
5 1
Front
view
(+) Ignition 1
PIN 3
Connect the start (+) wire output from remote starter
to pin 4 of key switch connector. If no wire to pin 4,
do not connect the start (+) wire.
PIN 4 (+) Start
Violet/Brown
Multiplex Output
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

Vehicle Type
Neon 1
PT Cruiser 1
RAM (with OEM Alarm Only) 2
Dakota 3
Durango 3
Vehicle Type Programming
Vehicle Type Chart
Page 5
ON
START
OFF
KEY
Remove Key
5Turn the key to the OFF position and remove it from the ignition barrel.
1Once all the wires are properly connected, plug the wire connector into the module.
The LED turns ON. On Solid
&
Press & Release
3To change the vehicle type, press and release the Programming button until the
LED flashing pattern matches the desired type.
For instance: 1 flash = Type 1, 2 flashes = Type 2 and so on. Flashing Pattern
2
Insert the key into the ignition barrel and turn it to the IGN position.
The LED turns OFF, then begins a flashing pattern that matches the vehicle
type selection (the default type is 1).
If the module has NEVER been programmed or has been RESET, the LED
will indicate which type the module is in by the number of flashes.
ON
START
OFF
KEY
Key at IGN Off
&
Flashing Pattern
&
4
To save the vehicle type selection, press and hold the Programming button until
the LED flashes once rapidly. The module will then exit the Programming mode
and is ready to be used.
If the LED turns ON solid, turn the key to start the engine.
If the module has already been programmed, the number of flashes
indicates once only the programmed type when applying power to the
module.
&
Press & Hold Flashes Once
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

User Configuration - Optional Programming
1Insert the key into the ignition at the OFF position and hold
the Programming button down for at least 2 seconds.
The LED flashes rapidly for 2 seconds to confirm you are
in programming mode. &
Flash 2 Secs
&
ON
START
OFF
KEY
Press & HoldKey at OFF
6Remove the key from the ignition barrel.
ON
START
OFF
KEY
Remove Key
5To exit the programming mode, hold the Programming button down until
the LED flashes once quickly.
Flashes Once
&
Press & Hold
3To change the MODE, press once on the Programming button. The LED
confirms the MODE with a number of slow flashes.
Only modes 6, 7 and 8 are available. &
Press Once
No. of Slow
Flashes = Mode
2Release the Programming button. The LED first flashes
a number of times slowly to indicate the MODE. It then
flashes a number of times quickly to indicate the OPTION. &
No. of Slow
Flashes = Mode
No. of Quick
Flashes = Option
&
Release
4
To change the OPTION in the selected MODE, press LOCK or
UNLOCK on the alarm or remote starter transmitter. The LED confirms
the OPTION with a number of quick flashes.
See the list of options at the bottom of this page.
&
No. of Quick
Flashes = Option
or
(
(
Press
USER MODES are identified by a slow LED flashing pattern. For example, 1 slow flash = Mode1 and 2 slow
flashes = Mode 2.
Page 6
Mode 6 - Lock when remote starter stops Mode 7 - Alarm control Mode 8 - Reset
*Option 1: Activate.
*Option 1: Vehicle with alarm. *Option 1: No reset.
Option 2: Deactivate. Option 2: Vehicle without alarm. Option 2: Complete reset of the
options and module.
* Default option.
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

LED Status Description Troubleshooting
During Power Up
Solid red Module not programmed. Data bus is not detected. Make sure the
connections to the data bus are correct by
referring to the wiring diagram, and then turn
the ignition to the ON position.
In rare cases, the vehicle will need to be
started in order to detect the bus.
Flashes continuously
by increments of one Chrysler Neon & PT Cruiser will be selected for programming. Must press and hold the Programming button for 3 seconds to select a type.
Flashes once then
turns off Chrysler Neon & PT Cruiser have been successfully programmed. N/A
Flashes continuously
by increments of two Dodge RAM will be selected for programming. Must press and hold the Programming button for 3 seconds to select a type.
Flashes twice then
turns off Dodge RAM has been successfully programmed. N/A
Flashes continuously
by increments of three Dodge Dakota & Durango will be selected for programming. Must press and hold the Programming button for 3 seconds to select a type.
Flashes thrice then
turns off Dodge Dakota & Durango have been successfully programmed. N/A
In Operating Mode
Solid red Incorrect behavior. Data is not being processed. Remove power
from the module, make sure the connections
to the data bus are correct by referring to the
wiring diagram, and then power up.
Flashes 1 second A D2D or W2W command is being
processed. N/A
Connect to
RAM (2001-03) Connect to
RAM (2004-05):
: Dark purple/Light blue wire in kick panel located under dash on driver side.
Light green/Orange wire in kick panel located under dash on driver side.
Tech Notes for Violet/Brown Wire
LED Diagnostics
Make sure this wire is connected as indicated below.
With Factory Alarm
With or Without Factory Alarm
Connect to Light green/Orange wire in kick panel located under dash
on driver side.
PT Cruiser (2000-05) Connect to White/Green wire coming from the driver door at the side kick panel.
Neon (2000-05): Connect to Light green wire kin kick panel located under dash on driver side.
* The BCM in the Dodge Dakota may go to sleep a minute after the doors have been locked and closed. If this happens a
ground pulse to the driver door pin switch (Tan in DKP) before unlock will wake-up the BCM and the doors will unlock.
Dakota* (2001-04) & Durango (2003 & earlier):
:
It is important to select the correct alarm option (mode 7) that corresponds to the vehicle you are currently performance
the installation on. See page 6 for more information on mode selection.
Page 7
x1*
x2*
x3*
x1
sec
* In this instance of the module diagnostics, the LED flashes in a continuous sequence.
x1
x2
x3
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.

This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select
vehiclelistupon completionofcompatibilitytesting.Visitwebsite forlatestvehicleapplicationguide. DISCLAIMER:Underno
circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any
consequentialdamagessustainedinconnectionwiththepart(s)installation.Themanufacturerandit’sdistributorswillnot,nor
willtheyauthorizeanyrepresentativeoranyotherindividualtoassumeobligationorliabilityinrelationtotheinterfacekit/data
bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this
product be liable for consequential damages sustained in connexion with this product and neither assumes nor authorizes
anyrepresentativeorotherpersontoassumeforitanyobligationorliabilityotherthanthereplacementofthisproductonly.
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics.(“DIRECTED”)promisestotheoriginalpurchaser, to repair orreplacewithacomparablereconditionedpiece,the
securityorremotestartaccessorypiece(hereinafterthe“Part”),whichprovestobedefectiveinworkmanshipormaterialunder
normaluse,providedthe following conditionsaremet:thePart was purchasedfromanauthorizedDIRECTED dealer; andthe
PartisreturnedtoDIRECTED,postageprepaid,alongwithaclear,legiblecopyofthereceiptorbillofsalebearingthefollowing
information:consumer’sname,address, telephonenumber,theauthorizedlicensed dealer’snameandcompleteproductand
Partdescription.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its
intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or
othercausesnotarisingoutofdefectinmaterialsorconstruction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS
WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSEAND
WARRANTYOFNONINFRINGEMENTOF INTELLECTUALPROPERTY,AREEXPRESSLYEXCLUDED;ANDDIRECTED
NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR ITANY DUTY, OBLIGATION OR
LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO
LIABILITY FORANYANDALLACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE EVENT OFA
CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO
COUNTYINTHESTATEOFCALIFORNIA.CALIFORNIASTATE LAWSANDAPPLICABLEFEDERALLAWSSHALLAPPLY
AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE
STRICTLYLIMITEDTO THEAUTHORIZED DIRECTED DEALER’SPURCHASEPRICEOFTHEPART. DIRECTEDSHALL
NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY
CONSEQUENTIAL DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS,
COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE
MANUFACTURERDOESOFFERALIMITEDWARRANTYTOREPLACEORREPAIRATDIRECTED’S OPTIONTHEPART
ASDESCRIBEDABOVE.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or
consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from
State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation,
promise, duty or obligation in connection with this Part.920-0007 07-06
PROTECTED BY U.S. PATENTS:5,719,551;6,011,460B1*;6,243,004B1; 6,249,216B1; 6,275,147B1;6,297,731B1; 6,346,876B1; 6,392,534B1; 6,529,124
B2; 6,696,927B2; 6,756,885B1; 6,756,886B2; 6,771,167B1; 6,812,829B1; 6,924,750B1; 7,010,402B1; 7,015,830B1; 7,031,826B1; 7,046,126 B1;
7,061,137B1; 7,068,153B1; 7,205,679B1; CDN. PATENT:2,320,248; 2,414,991; 2,415,011;2,415,023;2,415,027; 2,415,038; 2,415,041; 2 , 4 2 0 , 9 4 7 ;
2,426,670; 2,454,089EUROPEAN PATENT:1,053,128PAT. PENDING:2,291,306; MADE IN CANADA
Limited One-Year Consumer Warranty Page 8
Rev.: 20100302
Platform: XK09
Firmware: DLCH3
© 2010 Directed Electronics. All rights reserved.