XtendLan HCA-430M12 User manual

HCA-430M12 (IR 850nm, grey)
HCA-430IM12 (IR 940nm, army)
User's manual

Introduction 3
General Description 3
Applications 3
Parts and Controls 4
Installing the Batteries and SD Card 6
Loading Batteries 7
Using an External Power Source 7
Inserting the SD Card 8
Using the XtendLan CAM 10
The OFF,ON and SETUP Modes 10
OFF Mode 10
ON Mode 11
SETUP Mode 11
SETUP Mode Shortcut Keys'Functions 13
Using the SETUP Menu to Change Settings 13
Changing Parameter Settings in SETUP Mode 14
EXAMPLES-Changing the Settings of Some 15
The SETUP Menu-Parameters
and Settings List w/Descriptions 17
Mounting and Positioning the XTENDLAN CAM 2 1
Mounting 2 1
Sensing Angle and Distance Test 22
Switching ON the Camera
Playing Back/Deleting the Photos/Videos 23
Reviewing on the LCD 24
Deleting Photos or Videos 24
Reviewing Images Directly from the SD Card 25
Reviewing Images by Connecting the Camera to a Computer 26
Downloading the Photos/Videos 27
Troubleshooting/FAQs 28
Technical Speciications 33

General Description
About the XTENDLAN CAM
The XtendLan Cam is a digital scouting camera. It can
be triggered by
any movement of game in a location, detected by a
highly sensitive Passive lnfra-Red (PI R) motion sensor,
and then take high quality pictures (up to 12MP still
photos), or video clips.
The XtendLan Cam consumes very little power (less than
200mA) in a stand by (surveillance) state. This means it
can deliver up to six months stand-by operation time
when the device is powered by eight AA alkaline
batteries, and up to twelve months utilizing lithium AA
batteries. Once motion in the monitored area is detected,
the digital camera unit will be triggered at once (typically
within one second) and then automatically take photos or
videos according to previously programmed settings.
The XtendLan Cam is equipped with built-in infrare LEDs
that function as a flash, so that it delivers clear photos or
videos (in black & white) even in the dark, and it can
take color photos or videos under sufficient daylight. The
XtendLan Cam is designed for outdoor use and is
resistant against water and snow.
Applications
The XtendLan Cam can be used as a trail camera for
hunting or scouting game. It is also suitable for
surveillance usage.

[ PARTS AND CONTROLS
O PARTS AND CONTROLS
The XtendLan Cam provides the following connections
for external devices:
USB port, SD card slot, TV Out and external DC power
in(Fig. 1).
A three way power switch is used to select the main
operating modes: OFF, SETUP, and ON (Fig. 2).
A
control key interface with six keys is primarily used in
SETUP mode to select operational functions and
parameters. As shown
in Fig. 2, these keys are: UP,
DOWN, LEFT, RIGHT, OK and MENU. Four of the keys
can also perform a second function (shortcut operations
in SETUP mode) in addition to their main function: The
DOWN key can be used to set theVideo mode (movie
camera icon), and the UP key can set the camera to
Photo mode (still camera icon). The RIGHT key also
serves as the manual shutter ("SHOT") button of the
camera and the OK key switches the camera to the
payback ("REPLAY") mode. These secondary functions
are indicated by icons or text above the key as shown in
Fig.2.
FRONT VIEW
Fig.1: Connections
USB Por
LED IR Flash
Lens
Lock Hole
Motion/Low
Battery Indicator
PIR Sensor
SD Card Slot DC In
TV Out

7
Fig.2: Button and Switch Guide
INSTALLING THE BATTERIES and SD CARD
Before you begin learning how to use your XtendLan Cam, you
will first need to install a set of batteries and insert an SD card.
Although that may only take you a minute, there are some
important notes about both batteries and SD cards you should be
aware of, so please take the time to read the following directions
and cautions:
Loading Batteries
After opening the two latches on the right side
of the XtendLan Cam, you will see that the
XtendLan Cam has eight battery slots.
Starting at the top of the battery compartment,
slots 1 , 2, 3 and 4 form one group, while slots
5, 6, 7 and 8 form the other group, each
providing 6 volts in parallel. For maximum
battery life, you should install a full set of eight
batteries. The XtendLan Cam may also be operated by
just four batteries installed in the top group only (see right),
starting at slot 1. Battery life will be shorter with 4 batteries, but
the camera will operate normally. Whether you use 4 or 8, be
sure to insert each battery with correct polarity (negative or
"flat"end against the long spring of each battery slot). XtendLan
recommends using eight new lithium AA (Energizer? brand) or
alkaline AA batteries. NiMh Rechargeable batteries can also be
used, but they might have a shorter life span due to their reduced
efficiency over time and at low temperature. It is also possible to
use a lead-acid external battery cell with 6V output or suitable AC
adapter-see below for
more details.
Using an External Power Source (optional, user provided)
Optionally, you can connect an external 6V DC power source to
the"DC ln"jack at the bottom of the XtendLan Cam. It is
recommended to use a power source with a current output
greater than 1000mA. However, during bright daytime operation
when no flash is required, the XtendLan Cam

9
can function with much less current (>400mA). Please use a
compatible power source cable (not provided) to connect the
external DC power source with the power input jack of the
XtendLan Cam, making sure that the polarity is correct.
Note: The power connector is a 4.0x1 .7mm coaxial DC power plug
with positive”tip” (inside pin) polarity (Radio Shack P/274-1532 or
equivalent). If both an external power source is connected and
batteries are installed, the XtendLan Cam will be powered by the
external power source. When the batteries become weak, the low-
battery indicator LED will glow blue, indicating the batteries should
be changed.
Inserting the SD Card
The XtendLan Cams have 32MB internal memory, which can hold
only about 18 photos (12MP resolution). This is handy for testing
and getting familiar with the camera, but you will no doubt want to
leave the camera unattended for longer than a day, so using an
SD card is recommended. Insert the SD card (with the camera’s
power switch in the OFF position) before beginning to operate the
camera. Don’t insert or remove the SDcard when the power
switch is in the ON position. The XtendLan Cam uses a standard
SD (Secure Digital) memory card to save photos (in .jpg format)
and/or videos (in .asf format). SD and SDHC (High Capacity)
cards up to a maximum 32GB capacity are supported. Before
inserting the SD card into the card slot after opening the
camera's front cover, please makesure that the write-protect switch
on the side of he card is"off" (NOT in the"Lock"position). Following
describes how to insert and remove The SD card:
•lnsert the SD card into the card slot with its label side upwards
(see above). A"click" sound indicates that the card is installed
successfully If the wrong side of the card is facing up, you will
not be able to insert it without force-there is only one correct
way to insert cards. Ifthe SD card is not installed correctly, the
device will not display an SD card icon on the LCD in SETUP
mode (the SD card icon displayed after switching to SETUP
mode will have a"lock" symbol inside it in it if the cans locked).
Formatting the SD card by using the XtendLan Cam's
"Format"parameter before using it for the first time is
recommended, especially when a card has been used in other
devices (see "Changing Menu Parameter Settings"for
details) .
•To take out the SD card, just gently push in the card (do not try
to pull it out without pushing in first). The card is released from
the slot and ready to be removed when you hear the click.
WARNING
Be sure the camera’s power is switched OFF
before inserting or removing SD cards or batteries.

USING THE XTENDLAN CAM
Once you've prepared your XtendLan Cam by properly installing
batteries and an SD card, you could simply take it outside, strap it
to a tree, switch it on and leave-and you might get some great
photos that are exactly what you wanted. However, we highly
recommend that you first spend some additional time indoors with
this manual and your camera until you know a bit more about what
the 3-way switch and those control keys do. If nothing else, you'll
probably want to at least set the date and time so the camera will
imprint them (or not-it's your option) on your photos as they are
taken, learn how to set the camera to shoot video clips instead of
still photos if you like, and read some tips about mounting it on a
tree.
THE OFF, ON, AND SETUP MODES
The XtendLan Cam has three basic operational modes:
•OFF mode: Power switch in the OFF position.
• NO mode: Power switch in the ON position (LCD screen is off.)
•SETUP mode: Power switch at SETUP position (LCD screen is
on).
OFF Mode
The OFF mode is the"safe" mode when any actions must be taken,
e.g.,replacing the SD card or batteries, or transporting the device.
You will also use OFF mode if you connect the camera to a
computer’s USB port later to download your photos/ videos. And of
course, when you are storing or not using the camera, you will
switch it to OFF. Please note that even in the OFF mode the
XtendLan Cam still consumes power at a very low level.
Therefore, it's a good idea to take the batteries out of the battery
compartment if the camera will not be used for a long time.
ON Mode
Anytime after the batteries and SD card have been inserted, you
can switch on the camera. When the power switch is moved to the
top position, the camera will enter into the ON (Live) mode. The
motion indicator LED will blink red for about 10 seconds. This
interval allows time for you to close the XtendLan Cam’s front
cover, lock it,and leave the monitored area. Once in the ON mode,
no manual controls are needed or possible (the control keys have
no effect). The XtendLan Cam will take photos or videos
automatically (according to its current parameter settings) when it
is triggered by the PIR sensor’s detection ofactivity in the area it
covers.You can either move the power switch directly from OFF to
ON mode, or stop at the SETUP position irst to change one or more
settings, then move the switch to ON after you have inished doing
So.
SETUP Mode
In the SETUP mode you can check and change the settings of the
XtendLan Cam with the help of its built-in LCD (or a monitor
connected to the TV out jack). These settings, found in the SETUP
Menu, let you change the photo or video resolution, interval
between photos, switch the time imprint on, etc. Moving the power

switch to the SETUP position will turn on the LCD display, and you
will see an information screen that shows how many images have
been taken, the battery level, camera or video mode, etc (see Fig.
3 below).
NOTE: always move the power switch from OFF to SETUP
mode. It is possible that the camera could lockup if it is
switched from ON to SETUP mode. Ifthis occurs, simply move
the switch to OFF and then push it upto SETUP again..
Fig. 3: SETUP Information Screen (standard display model
shown)
SETUP Mode Shortcut Keys/Functions
As mentioned earlier in"Parts & Controls ,four of the keys below
the LCD have secondary, shortcut functions when the camera
is switched to SETUP mode (but the MENU key has not been
pressed):
Press the UP key to quickly set the camera to shoot video clips.
Press the DOWN key to quickly set the camera to take still photos.
Press the RIGHT key to manually trigger the shutter. This is useful
for testing the camera-make sure you are in SETUP mode, press
the RIGHT key, and a few seconds later a photo or video
(depending on how the camera was set) will be saved to the SD
card (or internal memory if no card is inserted). The number of
images taken counteron the bottom left of the LCD will increase
by one. If the display indicates”SD PROTECTED” when you press
the SHOT key, switch the camera OFF, remove the SD card and
slide its protect switch of. Press the OK key to replay (review or
playback) photos/videos on the LCD connected TV monitor . See
"playing Back Photos/Videos for more details.
USING THE SETUP MENU TO CHANGE SETTINGS
The main purpose of the SETUP mode is to allow you to change
the settings of the camera’s parameters (1 5 diferent ones are
available) so your XtendLan Cam operates exactly the way you
want it to. You will do this by entering the SETUP Menu and
pressing the keys below the LCD display, which will show you each
parameter and its setting.

Changing Parameter Settings in SETUP Mode
A wide range of options or parameters are provided to allow
you to set the XtendLan Cam to your operational preferences.
To change the setting of any parameter you must first switch to the
SETUP mode. Once in SETUP mode, pressing the MENU button
will allow you to select any parameter and change its setting. The
name of the parameter and its current setting will be shown on the
LCD. Pressing the RIGHT or LEFT key scrolls to the next or
previous parameter (RIGHT key to move on to the next parameter
and LEFT key to go back to the previous parameter), and pressing
the UP or DOWN key lets you select a diferent setting for the
currently displayed parameter. Once you have selected your
preferred new setting for a parameter, press the OK button to save
the new setting (actually change it). When have are finished
changing the settings of one or more parameters, press MENU
again to exit the SETUP menu. MENU can also be pressed
anytime you want to cancel changing a parameter's setting after a
new setting has been selected (but OK has not been pressed yet).
After setting the parameters to your preferences, be sure to move
the switch to ON to begin actually taking photos or videos. No
images will be captured if the switch is left in the SETUP position
PRESS MENU
MENU
PRESS OK
MENU
PRESS DOWN
MENU
(unless you press the RIGHT/Shot key after exiting the menu)-in
fact, the camera will power of automatically after a few seconds
with no key pressed.
Fig.4: Selecting Parameter Settings
EXAMPLES-Changing the Settings of Some Common
Parameters
Following this page, you will find tables listing all of the parameters
found in the SETUP Menu, along with their possible settings (or
range of settings), and a detailed description of what the parameter
controls and what the settings do. If you read the previous section
detailing how to select parameters and change their settings, you

17
Parameter
Settings
(Bold=default)
Description
Mode
Camera or
Video
Selects whether still photos or
video clips are captured when the
camera is triggered.
still photos)
SM PUMP
3M Pixel
Selects resolution for still photos from
3 to 12 megapixels. Higher resolution
produces better quality photos, but
creates larger files that take up more
of the SD card capacity (ills up faster).
12M is a good compromise between
quality and file size.
Capture
Number
(onlyafects
still photos)
1 Photo
2 Photo
3 Photo
Selects how many photos are taken
in sequence per trigger in Camera
mode. Please also refer to
the Interval parameter.
should be able to dive right in, find the parameter(s) you want, and
setup the camera to your preferences. But maybe you'd rather walk
through an example or two first:
To change any parameter's setting, always start with the power
switch in the SETUP position. After the LCD comes on, press the
MENU key.
The first parameter you will when you first enter the SETUP Menu
is Mode . To change it from its default setting of Camera
(still photos)to Video (shoot video clips), press the DOWN key
to highlight Video (color viewer models). Press the OK key to
execute (Set) the new setting you’ve selected for this parameter.
Now press the RIGHT key to move to another parameter in the
Menu. Pressing it four times will take you to"Video Length". Try
using the UP and DOWN keys to scroll through the range of
settings, then press OK to lock in your setting for the length of each
video clip the camera shoots.
Pressing the RIGHT key several more times will get you to
the"Default Set"parameter. Highlight or select"Execute"(using UP
or DOWN) and press OK to restore all parameters (including the
Mode and Video Length parameters you changed a minute ago)
back to their original factory default settings. The default settings
for each parameter are indicated in bold type in the SETU P Menu
tables on the next several pages.
Be sure to set the current date and time, using the"Set
Clock"parameterif you choose to change the"Time Stamp"parameter
setting to"On"since that will tell the camera to imprint the date and
time on each of the images it captures.
The SETUP Menu-Parameters and Settings List w/Descriptions

19
Video Size
(only afects
video clips)
Video Length
(only afects
video clips)
Interval
Sensor Level
1280x720
640x480
320x240
1OS (second)
default, with
SS to 60S
possible range
IOS (second)
default, with a
60M (minute)
to1S (second)
range of settings
available.
(60M-1 M are set
in one minute
increments,
59S-1S are set in
one second
increments)
Normal, High,
Low
Selects video resol ution (in pixels per
frame). Higher resolution produces
better quality videos, but creates larger
files that take up more of the SD card
capacity (fills up faster). 640x480 is
VGA video in standard 4 3 format.
Sets length per captured video cl ip.
Settings begin with 10 second default
when parameter is first selected. After
stepping down to SS, video length
settings start over at 60S.
Selects the length of time that the
camera will"wait"until it responds to
any additional triggers from the PIR
after an animal is first detected and
remains within the sensor’s range.
During this user set"ignore triggers"
interval, the camera will not capture
photos/ videos. This prevents the
card from filling up with too many
redu ndant images. Settings begin with
10 second default when parameter is
first selected. Note after setting down
past"1S,"settings start over at"60 M".
Selects the sensitivity of the PIR
sensor. The"H igh"setting will make the
camera more sensitive to infrared
(heat) and more easily triggered by
motion, and the"Low"setting makes it
Format
TV Out
Time Stamp
(only afects
still photos)
Execute
(followed by
an additional
No/Yes step
on color
viewer models
only)
NTSC, PAL
Off, On
less sensitive to heat and motion. The
High setting can be useful when he
ambient tern perature is warm(making it
more difficult for the sensor to detect
animals), and the Low setting may help
in cold weather if the camera is being
triggered too often by anyth ing warmer
than the surroundings.
Deletes (erases) all files stored on a
card to prepare it for reuse. Always
format a card that has been previously
used in other devices. Caution! Make
sure you have downloaded and backed
up any files you want to preserve first!
Press OK to execute (then select Yes
and press OK again on color viewer
models), press MENU (or select NO
then press OK) to exit without
formatting.
Selects video standard /format for
the"TV Out"output jack. The video
standard is NTSC for the United
States, Canada, Mexico, Asia and
South America. PAL is used primarily
in Europe.
Select"On"if you want the date& time
(that the photo was captured) imprinted
on every photo, select"Of"for no imprint.

Set Clock
Set
Press OK and use the UP/DOWN keys (to change the
setting) and LEFT/RIG HT keys ( to move to the next
ield) to set the hour (24-hr format only, "00"-
midnight,"12"=noo and minute, and then (on the lower
row), the year, month and date.
Turn Timed Scan recording mode on/off . When
activated, Timed Scan forces the camera to take photos
or videos even when it is not triggered by a nearby live
MOUNTINGAND POSITIONING the XTENDLAN CAM
Mounting
After you’ve set up the camera’s parameters to your personal preferencesat
home or in your truck, you’re ready to take it outside and slide thepower
switch to”ON”. When setting up the XtendLan Cam for scouting game or
other outdoor applications, you must be sure to mount it in place correctly
and securely. We recommend mounting the XtendLan Cam on a sturdy
tree with a diameter of about 6 in. (15cm). To get the optimal picture quality,
Set Timed Scan or,off
Set Video Sound On,Off
Password Set On,Off
animal, useful for constant monitoring of an area that
might be far away from the camera. The user can set
the start and stop times for up to two independent
"blocks" of Timed Scan recording, as well as the
interval time between each photo/video.
Press "on" the camera will record the sound when in
video mode. Press "off" the sound will be closed.
Select "on" set a password then input the
password.Select "off" to close the password function.
Select"Execute"and press OK to restore all parameters
to the original factory default settings. If the camera is
the tree shouId be about 16-17 ft. (5 meters) away from the place to be
monitored, with the camera placed at a height of 5-6.5 ft. (1.5-2 in). Also,
keep in mind that you will get the best resuIts at night when the subject is
within the ideal lash range, no farther than 45’(14m)and no closer than 10’
(3m) from the camera.
There are two ways to mount the XtendLan Cam: using the provided
adjustable web belt, or the tripod socket.
Using the adjustable web belt: Fig. 5 illustrates using the web belt on the
XtendLan Cam. Push one end of the belt through the two brackets on the
back of the XtendLan Cam. Thread one plastic buckle part onto each end of
the belt. Fasten the belt securely arou nd the tree trunk by clicking the
buckle ends together after tighten ing the belt so there is no slack left.
Default
Cancel,
Execute
behaving oddly and you think you may have changed
the setting for something accidently (but aren’t sure
which one), this will reset all parameters to their most
commonly used or " generic" settings.

Using the tripod socket : The camera is equipped with a socket at the bottom
end to enable mounting on a tripod or other mounting accessories with a
standard 1/4-20thread.
Sensing Angle and Distance Test
To test whether the XtendLan Cam can effectively monitor the area you choose,
this test is recommended to check the sensing angle and monitoring distance
of the XtendLan Cam. To perform the test:
• Switch the XtendLan Cam to the SETUP mode.
• Make movements in front of the camera at several positions within
• the area where you expect the game or subjects to be. Try diferent distances
and angles from the camera.
• If the motion indicator LED light blinks, it indicates that position can be
sensed. If it does not blink, that position is outside of the sensing area. The
results of your testing will help you find the best placement when mounting and
aiming the XtendLan Cam. The height away from the ground for placing the
device should vary with the animal size appropriately. In general, 3 to 6 feet is
preferred.You can avoid potential false triggers due to temperature and motion
disturbances in front of the camera by not aiming it at a heat source or nearby
tree branches or brush (especially on windy days).
Switching ON the Camera
Once you switch to the ON mode, the motion indicator LED (red) will blink for
about 10 seconds. This gives you time to close and lock the front cover of the
XtendLan Cam and then walk away. During this time, the motion indicator
LED will blink red continuously. After it stops blinking, the PIR is active, and
any motion that is detected by it will trigger the capture of photos or videos as
programmed in the SETUP Menu. Be sure you have read the descriptions of
the Capture Number, Video Length, Interval and Sensor Level parameters.
Please note, the sPlR is strongly sensitive to ambient temperature. The greater
the temperature diference between the environment and your subject, the
farther the possible sensing distance. The average sensing distance is about
45 ft.
Before leaving the camera unattended, please check for the following:
• Are the batteries or DC power supply inserted/connected with correct polarity
and is the power level is suicient?
• Does the SD card have sffuicient available space and is its write-protection
(lock) switch off?
• Isthe Power switch inthe ON position? (do not leave it in SETUP).
PLAYING BACK/DELETING the PHOTOS/VIDEOS
After you have setup, mounted and activated your XtendLan Cam, you will of
course be eager to return later and review the images it has captured for
you. There are several diferent ways this can be done.
Reviewing Images on the XtendLan Cam LCD (Models with Color
Viewer only)
• Put the power switch in SETUP mode (switch to OFF irst).
• Push the OK(Replay) key to enter image review mode.
• Use the UP/DOWN keys to scroll through your photos or videos. The right
corner of the display will indicate”JPG”for still photos,and a film icon for video
iles. Press the RIGHT(Shot) key to review a video.

• Push MENU to delete an image. Image delete mode works as described
below. To exit image review mode, press the OK key.
Reviewing Images on an External Video Monitor
A TV monitor can also be used to play back pictures (or videos) from the
device. Connect a TV monitor or a viewing device (such as a digital picture
frame) that has a standard composite video input (RCA jack) to the XtendLan
Cam’s ”TV Out”mini jack using the supplied cable. Then:
•Put the power switch in SETUP mode (switch to OFF first).
•Press the OK key. The most recently
captured image will be shown on the
video monitor. For video clips, press
the SHOT (RIGHT) key to start playing,
press again to stop.
•Press the UP key for the previous
photo or video and the DOWN key
for the next one. When viewing images,
the total number of all images in the SD card and the index of the displaying
image are shown in the center of LCD and at the bottom of the video monitor
respectively.
•Press the OK key to return to live preview state (SETUP mode) when
playback is finished.
Deleting Photos or Videos
If you see a photo or video during playback on the LCD or video monitor that
you want to delete, it can be done easily without leaving SETUP mode:
• Press the MENU key. You will see the first”Delete”screen, which lets you
selects the option to delete only the currently displayed photo/video, or all
photos/videos (see below).
• Highlight the”Delete Current”or”Delete All”option, then press OK.
• Next, select”Yes”and pres OK to erase only the last displayed photo or video
(if you selected”Delete Current”), or every photo and video file on the card (if
you selected”Delete All”or select”No”and press OK to cancel the operation
without deleting any files.
NOTE: after deleting a picture or a video file, the deleted files cant
berestored! It isalso possible to delete all files from the card by using the
Format parameter.
Reviewing Images Directly From the SD Card
This is the most popular method of viewing images. Since
unmounting the camera and taking it to your computer isn’t very
convenient, you mayfind it easier to just take the card out. By
removing the SD card (swapping it for a new empty card if you like)
and taking it to your home or campsite to view the images by using
an SD card"reader"(user supplied) connected to your computer
(some computers and TVs have a built in SD card slot), you can
leave the camera in place ready to capture more images. Once
connected, the card reader works the same way as described
below-please read that section if you have any problem finding
your files.

Reviewing Images by Connecting the Camera to a Computer
You can always unmount the entire camera from the tree and
connect its USB port to a computer-it will be recognized as
a"removable disk",without the need to install any drivers or
software. When using a PC (or Mac‘) to view photos (or video
clips), first connect the device to the computer with the supplied
USB cable. Then use commercial software with an image browser
feature, or an image browser included with the PC’s operating
system to view images saved on the SD card in the folders DCIM
100EK113. Each new image or video will be numbered
incrementally in order of the time it was captured. For example, you
will see file names such as "PlCT0001 .JPG"or"PlCT0001.ASF".
Through the file format suffix you can distinguish whether the file is
a still photo (with suffix .jpg) or a video (with suffix .asf).
”"ASF"video iles may require additional software for viewing
on a Mac
The XtendLan Cam supports 3 kinds of file system formats,
FAT12, FAT16, and FAT32.
The default value is FAT16 to save photos and videos. Here are
some related notes:
• You don’t need to be concerned about the file system format of
the XtendLan Cam unless your equipment has problems reading
the SD card. If this happens, please format the SD card with the
XtendLan Cam or in your computer first and then insert the card
into your XtendLan Cam and try again.
•The default file system format of the XtendLan Cam is FAT1 6,
which most computers can read. If you format an SD card for the
XtendLan Cam in your computer, you should choose the file
system format FAT1 6. Normally FAT1 6 is recommended unless
you have another image viewer that uses FAT12 or FAT32 format.
DOWNLOADING THE PHOTOS/VIDEOS
To download your photos/videos to a PC or Mac, first make sure
the XtendLan Cam power switch is in the OFF position. Connect
the supplied cable to the camera’s USB port, then directly to a main
USB port on your computer-do not use front panel/keyboard USB
ports or unpowered "hubs"The XtendLan Cam will be recognized
as a standard"USB Mass Storage"device (this may take several
seconds the first time you connect it). If you would rather leave
your camera in the woods and just pull its SD card out, an SD card
reader works the same way as described in this section once the
card is inserted and the reader is connected to your computer.
With Windows XP or later, you can then
simply use the options in the pop-up
window to copy, view, or print your
photos (right).
On all Windows OS, the XtendLan Cam
will also be listed as a"Removable Disk"if
you open the"My Computer"window (on Macs, an icon will appear
on your desktop). The XtendLan Cam’s photo files are named
27

"PICT0001 .JPG" etc,and are located in the "DCIM\1 00EK11 3"
folder on this"Removable Disk". Video file names will end
with".ASF".You may copy the photos/videos to your hard drive as
you would any file-just copy/paste or drag the file names or icons to
your drive or desktop.
After the photos are copied to your hard drive, you can disconnect
the XtendLan Cam. (On Mac computers, drag the"disk"that
appeared on your desktop when the camera was connected into
your Trash to"eject"itbefore disconnecting.) The .jpg standard files
from the XtendLan Cam may be viewed and edited with any photo
software you choose to use. The .asf video files may be viewed
with Windows Media Player (version 7 or later) as well as other
video playback programs that may have been supplied with your
computer, or are available online.
”".ASF"video files may require additional software for viewing
on a Mac.
Troubleshooting / FAQ
Battery life is shorter than expected
1. Battery life will vary with operating temperature and the
numberof images taken over time. Typically, the XtendLan Cam
will be able to capture several thousand images before the
batteries die.
2. Check to make sure you have used new alkaline or lithium
batteries. XtendLan recommends using 8 Energizero Lithium AA
batteries in all XtendLan Cams to obtain maximum battery life.
3. Make sure that the power switch was turned to the"On"positio
and that the camera was not left in"Setup"mode while in the field.
4. Make sure that you are using a good quality name brand SD
card in your camera. XtendLan recommends San Disko brand SD
Cards up to 32GB. Our experience indicates that poor quality SD
cards can sometimes reduce your XtendLan Cam battery life.
Camera stops taking images or won't take image
1 . Please make sure that the SD card is not full. If the card is full,
the camera will stop taking images.
2. Check the batteries to make sure that they are new alkaline or
lithium AA batteries. See note above about short battery life.
3. Make sure that the camera power switch is in the "On"
positionand not in the "Off' or "Setup" modes.
4. Make sure that you are using a good quality SD card in your
camera. XtendLan recommends SanDiskOSD Cards up to 32GB.
5. If the SD card has its write protect switch in the lock position, the
camera will not take images.
6. If you have used an SD card in another device before inserting
it in your XtendLan Cam, you might want to try formatting the card
using the"Format" parameter in Setup mode (make sure you have
backed up any important files first, as formatting will erase all
previous files). I n some cases, other devices may change the
formatting of the SD card so that it will not work properly with the
XtendLan Cam.
B9

Troubleshooting / FAQ
Camera won't power up
1. Make sure that you have installed at least 4 batteries (the
required minimum #) in the battery compartment, starting at the
top, filling battery spaces 1-4 with no "gaps"
XtendLan recommends using 8 Energizero Lithium AA batteries in
all XtendLan Cams.
2. Make sure that the batteries are installed correctly, observing
proper polarity. Always place the negative (lat) end of each battery
in contact with the spring side of its slot inside the camera.
3. After moving the switch from "Off' to "Setup" or "On",make sure
that the switch is correctly in position to ensure the proper mode
(avoid positions "between" two modes).
4. Do not move the switch directly from "On" to "Setup"-alway
move the switch all the way down to "Off' first, then back up to
"Setup".
Still Photo and/or Video Quality Problems
1. Night photos or videos appear too dark
a. Check the battery indicator icon to see if battery power is full.
The flash will stop operating near the end of the battery life.
b. You will get the best results when the subject is within the ideal
flash range, no farther than 45'(14m) from the camera. Subjects
may appear too dark at greater distances.
c. Please note that when the Capture Number parameter is set
higher than "1 Photo", or with very short Interval settings, some
images may appear darker than others due to the quick response
and rapid retriggering of the camera, allowing less time for the
flash to fully recharge before firing again.
2. Daytime photos or videos appear too dark
a. Make sure that the camera is not aimed at the sun or other light
sources during the day, as this may cause the auto exposure to
produce darker results.
3. Night photos or videos appear too bright
a. You will get the best results when the subject is within the ideal
flash range, no closer than 10’ (3m) from the camera. Subjectsmay
appear too light at closer distances.
4. Daytime photos or videos appear too bright
a. Make sure that the camera is not aimed at the sun or other light
sources during the day.
5. Photos with streaked subject
a. I n some cases with low lighting conditions and fast moving
subjects, the SMP or 8MP resolution settings may not perform as
well as the 3MP setting.
b. Ifyou have multiple images where fast moving subjects produce
streaks on the photo, try the 3MP setting instead.
6. Red , green or blue color cast
a. Under certain lighting conditions, the sensor can become
confused resulting in poor color images.
b. If this is seen on a consistent basis, then the sensor may need
servicing. Please contact XtendLan customer service.
7. Short video clips!anot recording to the length set
a. Check to make sure that the SD card is not full.
b. Make sure that the camera has good batteries in it.Near the end
of the battery life, the camera may choose to record shorter video
clips to conserve power.

Iwage Sensor
5Megapixel Color CMOS
Lens
F=2.8; FOV=40”Auto IR-Cut-Remove(at night)
IR-FlashRange
36'-45'(12m-15m)
Display Screen
1.5 inch Std B&W Display; 2.4 inch Color Display
Memory Card
SD or SDHC Card, Maximum capacity 32GB
Internal RAM
32M
Date/Time Stamp not appearing on images
Make sure that the "Time Stamp" parameter is set to "On"
Photos Do Not Capture Subject of Interest
1. Check the "Sensor Level" (PI R sensitivity) parameter setting.
For. warm environmental conditions, set the Sensor Level to "High"
and for cold weather use, set the sensor for "Low"
2. Try to set your camera up in an area where there is not a heat
source in the camera's line of sight
3. In some cases, setting the camera near water will make the
camera take images with no subject in them. Try aiming the
camera over ground.
4. Try to avoid setting the camera up on small trees that are prone
to being moved by strong winds.
5. Remove any limbs which are right in front of the camera lens.
PIR Sensor LED Flashes/Doesn't Flash
1. When the camera is in the "Setup" mode, a special LED on the
front of the camera will flash when it senses motion. This is for
setup purposes only and will help the user aim the camera.
2. During use, the LED will not flash when the camera takes an
image. This is to help keep the camera hidden from game.
LCD Screen Issues
1. LCD screen powers on but no text is present.
a. After moving the switch from "Off' to "Setup" or "On",makesure
that the switch is correctly in position to ensure the proper mode
(avoid positions "between" two modes).
b. Do not move the switch directly from "On" to "Setup"-always
move the switch all the way down to "Off' first, then back up to
"Setup"
2. LCD screen shows a faint black line after turning from
"Setup" to "On"
a. The LCD will turn off when you slide the switch to the "On"
position. In some cases, this black line will appear and then fade in
about 1 second. This is normal and the camera will function
properly.
3. Screen comes on but then powers off
a. Make sure that you have installed the SD card correctly.Camera
won!'t retain settings
1. Make sure that you have been saving the changes to any param-
eter settings that you made while in Setup mode, by pressing "OK"
after changing the setting. If you don!-t save your new setting
afterchanging it, the camera will continue to use the original default
setting for that parameter.
TECHNICAL SPECIFICATIONS

Iwage Size
Video Size
PIR Sensitivity
Operation
Response Time
Triggering Interval
Shutter Speed
Shooting Numbers
Video Length
Power Supply
Stand-by current
Power Consumption
Timed Scan
Temperature Display
Password
Moon Display
Audio Video
User Interface
Interface
Security
12MP 4000× 3000 ;8MP 3264 ×2448 ,
SM(2592X1944); 3M (2048X1536);
1280×720; 640×480;320×240;
PIR with 3sensitivity levels:High/ Normal/ Low
Day/Night
0.7 s
1sec-60minprogrammable
1/10-1/2000sec.
1-3 programmable
5-60sec.programmable
8×AA recommended;4×AA as emergency power
<0.28mA
<200mA(+600mA when IR-LED Lighted)
programmable
programmable
programmable
programmable
programmable
LCD display
TV out(AVl);USB;SD card holder; 6V DC external
Strap;1/4-20 attachment
Operating Temperature -20-60”C Storage temperature:-30-70”C
Operating Humidity 5%-90%
Security Authentication FCC/CE/RoHs/WE EE