Yashica 35mm ELECTRORANGE-FINDER User manual

Page 1of 1
35mm YASHICA ELECTRO
RANGE-FINDER MANUAL
This Document was Updated on January 2, 2005
This Update adds Support to Questions Most Frequently Asked Since the Last
Revision
Entire Contents © 1999 –2005 by Joe Marcel Wolff
All Rights Reserved. Copies May be Printed Out for Personal Use

Page 2of 2
35mm YASHICA ELECTRO
RANGE-FINDER MANUAL
KEY STEPS FOR AUTOMATIC PHOTOGRAPHY
WITH THE G SERIES
1.Load and Check Battery
2.Unlock Shutter Release Button
3.Load Film
4.Set ASA Film Speed
5.Set Camera for Automatic Operation
6.Select Appropriate Exposure Symbol
7.Focus
8.Control Exposure -- using “Over -Under” Lamps....SHOOT!

Page 3of 3
BATTERY LOADING AND CHECKING
1.Unscrew the BatteryCompartment Cover with the edge of a coin.
2.Mercury battery sales are prohibited. Therefore use of the Yashica Guy Pro
Battery Adapter is suggested to replace the original types Mallory TR 164,
Eveready E164 or discontinued Duracell PX 32 Alkaline battery.
3.When the camera will not be in use for a while, be sure to remove the
battery and store it in a dry cool place, to avoid a battery leak that could ruin
your camera.
4.Check battery before picture-taking. Press Battery Check Button. If the
green light comes on in the Film Exposure Counter, the battery power is
sufficient. If not, the battery should be replaced.
FILM LOADING (Always load in subdued light)
1.Pull out Film Rewind Knob, and Back Cover will pop open. The Film
Exposure Counter is automatically set at "S" (Start).
2.Place a 35mm film cassette into film chamber and push down the Film
Rewind Knob.
3.Insert film leader into Take-up Spool and advance film with the Film
Advance Lever, making sure the perforations properly engage the sprocket
teeth. CloseBack Cover.
4.Gently wind the film rewind crank-handle on Film Rewind Knob, until a slight
resistance is felt, to remove film slack.
5.Advance film, then press shutter Release Button, and repeat until the figure
"1" appears in the Film Exposure Counter.
6.Make sure the film is properly loaded. As you advance the film, the Film
Rewind Knob should rotate counter-clockwise.
ASA FILM SPEED SETTING
Align the mark on the ASA Film Speed Index Setting Ring with the ASA / ISO
rating of the film in use. The Film rating is shown on the box or the instructions that
come with the film. (DIN film speed rating conversion table is given inside the
camera).
SHUTTER RELEASE BUTTON
To lock the Shutter Release Button, align the mark on the Shutter Release LOCK
with the letter"L". To unlock, give Lock ¼ turn clockwise. When camera is not in
use, the shutter should not be left cocked, and the Shutter Release Lock should be
in the locked position.

Page 4of 4
AUTOMATIC OPERATION
For automatic operation, set the Exposure Control Ring to AUTO position. (With
the use of exclusive Lens Shade provided with the GT model, the Exposure
Control Ring will lock at the AUTO position.)
EXPOSURE SYMBOLS
Select the appropriate Exposure Symbol and set it opposite the mark by turning the
Aperture Ring.
SUN or CLOUD symbol -for outdoor photography.
WINDOWsymbol -for indoor and night photography.
This should bring you close to the correct exposure with 100 ASA / ISO film. Use
the “Over -Under” lamps to zero in.
FOCUSING
1.Sight through the Viewfinder and turn the Focusing Ring until the two
images in the center focusing area form one clear image.
2.Compose picture within the bright frame that, during focusing, in particular at
short distances, moves diagonally for automatic parallax correction.
EXPOSURE CONTROL
1.The RED and YELLOW warning arrows in the Viewfinder and on the
camera top are actuated when the Film Advance Lever is wound and the
Shutter Release Button is pressed in half way. Practice this without film in
the camera.
2.The absence of both arrows signifies hand-held photography is possible. All
you need do for a perfect picture is FOCUS and PRESS the Shutter
Release Button down all the way. The appearance of the RED arrow ( when
the Shutter Release Button is half -pressed ) signifies too much light. Turn
the aperture Ring in the direction of the arrow until it disappears.
If it fails to disappear, a neutral density filter should be used and the ASA
Film speed Setting Ring reset accordingly. If the original setting was ASA
100, reset to ASA 25 when an ND4 Neutral Density filter is used. With The
MG-1 and the GL models, do not reset the ASA. The Electronic Exposure

Page 5of 5
Control [EEC] in the lens mount will correct for this because it "sees"
through the filter in place.
3.The chart below is a convenient guide to resetting the ASA Index on your
camera to compensate for the filter in use. Guide numbers that are shown
on the film package are now generally displayed as ISOnumbers. These
are identical to the earlier ASA rating Index.
Convert ASA /ISO Index to FILTER FACTOR
Colour or Neutral Density Filter Factor
ASA
1.5
2
2.5
3
4
5
8
12
16
32
1000
650
500
400
320
250
200
125
80
64
40
800
500
400
320
250
200
160
100
64
50
32
650
400
320
250
200
160
125
80
50
40
25
500
320
250
200
160
125
100
64
40
32
20
400
250
200
160
125
100
80
50
32
25
16
320
200
160
125
100
80
64
40
24
20
12
250
160
125
100
80
64
50
32
20
16
10
200
125
100
80
64
50
40
25
16
12
8
160
100
80
64
50
40
32
20
12
10
6
125
80
64
50
40
32
25
16
10
8
5
100
64
50
40
32
25
20
12
8
6
4
80
50
40
32
25
20
16
10
6
5
3
64
40
32
24
20
16
12
8
5
4
2.5
50
32
25
20
16
12
10
6
4
3
2
40
25
20
16
12
10
8
5
3
2.5
1.6
Yashica Guy has rounded off results to the nearest ASA setting

Page 6of 6
EXPOSURE INDICATORS
The appearance of the YELLOW arrow signifies too little light for hand-held
photography, since the exposure speed will be slower than 1/30 second. Turn
the Aperture Ring in the direction of the arrow until it disappears. If it fails to
disappear, use a tripod. (Yashica convertible Grip/Tripod ST-7 is handy to lean
up against a wall or post for support ). Whether the YELLOW arrow disappears
or not, the precise exposure speed will be determined and set automatically to
a maximum of 30 seconds.
CONTROL OF SHUTTER SPEED
The Electro Exposure control system is of the Aperture Priority type. You select the
lens opening and it sets the shutter speed for the correct exposure. This normally
works out very well
You can however overcome this and control the shutter speed, for sporting events
for example.
When you understand the relationship between the aperture stops and the
percentage of light between them, it actually becomes quite simple to select the
shutter speed best suited for your shots.
Each ƒ stop on the lens barrel, namely, 16 -11 -8 -5.6 -4 -2.8 -2 -1.4
represents a 100% change from the adjoining setting. As the numbers get larger,
the amount of light transmitted by the lens becomes LESS, because this number is
NOT the size of the lens opening but is the ratio of the sizeof the lens opening
[aperture] to the focal length of the lens. With this in mind, it is not difficult to follow
the procedure.
In daylight photography, set the lens opening to maximum for the sake of
simplicity. This is 1.7 on the 'G' series. Now slowlypress the shutter release button
until you see the red over exposure lamp. Then adjust the lens opening until both
the red and yellow lamps are out. At this point your camera is set for the correct
exposure with the shutter set at 1/500th sec. If you wishto cut the shutter speed in
half to 1/250th second for the sake of greater depth of focus, move the indicated
lens opening on the barrel to the next 100% smaller aperture setting. For example
if the lamp went out at ƒ 5.6, decrease the lens opening by 100% to ƒ 8.0
Obviously you can move from one mid point to the next. To obtain an exposure of
1/125th second, you would move the lens by two increments to ƒ11. Try this
without film in the camera to get the hang of it.

Page 7of 7
It is also possible to use an Exposure Meter to determine the correct Aperture to
get the Shutter Speed that you would like the camera to use. Just set the Exposure
Meter’s selected Aperture for that speed on the camera, and the Electro Shutter
will automatically match the correct Shutter Speed. Use of an Incident Light meter
is highly desirable.
FILM UNLOADING(ALWAYS UNLOAD IN SUBDUED LIGHT)
1.After the last exposure, DO NOT try to advance the film further as it may
tear or come loose, making it impossible to rewind the film into the cassette.
2.Before removing it from the camera, the film should be rewound into its
cassette. Press the Film Rewind Release Button on the bottom plate of the
camera. If you fail to do this, you may tear the film perforations or even
damage the camera mechanism.
3.Unfold the crank handle on the Film Rewind Knob and very slowly turn it in
the direction of the arrow until a slight resistance is felt. Continue slowly
winding until you feel it turning freely. Caution. If you wind too quickly under
conditions of low humidity, you may cause static-electricity to discharge onto
your film, resulting in light streaks on the negative. Gently allow the rewind
handle to turn as the film may unwind itself within the cassette. If the film
turns too quickly, static marks will fog and ruin your negatives.
4.Open the Back Cover, remove the cassette and send for processing.
DEPTH OF FIELD
1.Depth of field is the area in front and behind the subject on which the
camera is focused. within which all objects also appear acceptably sharp in
the picture. It varies with the aperture and is more extensive.
a.When the lens is stopped down
b.When the camera is focused on a distant subject
c.In the background rather than the foreground
2.The depth of field can be determined by reference to the depth-of-field scale
on the lens barrel. With the camera focused on 2 meters and an aperture of
f/16, the depth of field will be from 1.4 to 3.8 meters, i.e. the range enclosed
by the number 16 on both sides of the red index mark.

Page 8of 8
SELF-TIMER
1.If you want to include yourself in the picture, use the Self-Timer and proceed
as follows:
a.Advance the film
b.Move Self-Timer Lever down all the way in the direction of the arrow
c.Press Shutter Release Button and the shutter will click about 8
seconds later.
“B” SETTING
Since the shutter will operate automatically for long time exposures, “B” setting
[ Bulb ] is used only very occasionally, mainly for special effects. At “B” setting the
shutter will remain open for as long as the Shutter Release Button is kept
depressed.This function requires a battery in the camera.
1.Align the “B” symbol on the Exposure Control Ring with the red triangular
mark.
2.The use of a tripod and cable release is essential.

Page 9of 9
FLASH EXPOSURE
To stop movement in dim light, use flash.
The Electro G's require that the camera battery be installed to trigger flash
exposures. Mount a Strobe Flash Gun in the Accessory Shoe and connect the
synchro cord to the Flash Sync. [PC] Terminal. The GSN / GTN and GL have both
a Hot Shoe and PC terminal.Flashbulbs can be used when the indicator on the
lens is set at the lightening bolt symbol. Some models have an M & X selector. X is
for Strobe [Electronic Flash]. All these models in the G group will synch Strobe in
the AUTO setting at all but the highest shutter speeds for outdoor fill light.
If you plan to use a strobe flash with the Electro 35, G or GS that does not have a
hot shoe, you need to place insulation tape on the base of the shoe to prevent the
flash from shorting out.
If you do not followthis, a charged flash will fire as soon as it is installed, or simply
drain it's batteries when switched on after it is installed. The use of one of the older
strobe flash units without a hot shoe contact will avoid this problem as well as the
use of a Flash Bracket [highly recommended].
If you still have flashbulbs and want to have some fun, align the Flash Symbol on
the exposure Control Ring with the red triangular mark. The shutter speed is
automatically set at 1/30 sec. [ “M” type, flash-bulb synch ]. Focus the camera and
divide the guide number of the strobe flash or flash bulb by the flash-to-subject
distance. The figure thus obtained should be set by turning the Aperture Ring.
Example: ASA 100 film -guide number 84 -divide by distance (15 ft.) equals f/5.6
aperture. NOTE: The guide number differs with ASA film speeds.

Page 10 of 10
FOR BETTER PICTURES
1.For better color pictures, shoot in soft, diffused light.
2.When shooting by available light indoors, be aware that the colour of nearby
objects or walls, will be reflected onto the subject. This can result in
undesirable colour tints that cannot be compensated for in printing. Also pay
attention to your clothing that can reflect colour particularly while shooting
close-ups.
3.When the YELLOW arrow in ON, use a tripod (also with B and Self-Timer).
4.When the main subject is the point of interest, use the largest aperture
suited for the prevailing light. If a greater depth of field is required, stop
down the aperture as necessary.
5.When it is necessary to stop action in outdoor photography, turn the
Aperture Ring to where the RED arrow just disappears. At this point, the
shutter is about 1/500 sec.
6.When photographing spot-lighted subjects or against light, reset the ASA
Film Speed Index Setting Ring.
Example with ASA 100 film:
9Strong spot-lighted subject -reset to ASA 200-400.
9Against light -reset to ASA 50 or 25.
9The use of a Neutral Density [ND] or Polarizing filter when shooting in
blazing sunlight, snow or beach scenes is recommended. Reset the
ASAFilm Speed Index Setting Ring according to filter factor, unless
you are using one of the models that have the Exposure sensor
within the lens mount. e.g. MG-1, GL. For night photography,
WITHOUT FLASH, set the Exposure Control Ring at the AUTO
position and the Aperture Ring at the INDOORS (window) symbol. In
all cases, the shutter speed will be determined and set
AUTOMATICALLY. However, when shooting with the YELLOW arrow
on, use a tripod.