Yoda VG400R User manual

VoIP Router
User’s Guide
i

Trademarks
Contents are subject to revise without prior notice.
All trademarks belong to their respective owners.
FCC Warning
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause
radio interference in which case the user will be required to
correct the interference at his or her own expense.
CE-mark Warning
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case the
user may be required to take adequate measures.
Revision
INSTALLATION GUIDE
V1.0
ii

TABLE OF CONTENTS
1. ABOUT THIS GUIDE......................................................1
1.1 Before Start up ...................................................................1
1.2 Notation Conventions (for console or telnet setting).......2
2. START UP PREPARATION...........................................4
3. WAN CONFIGURATION ...............................................5
3.1 Static IPAddress Environment.........................................5
3.2 Dynamic IPAddress Environment.................................11
3.2.1Applying for a host name in the dynamic IP
environment ..............................................................12
3.2.2PPPoE application set up...........................................13
3.2.3DHCPapplication set up............................................18
4. LAN CONFIGURATION...............................................24
4.1 LAN Interface Configuration .........................................24
5. ADVANCED FEATURES..............................................29
5.1 Access to Advanced Features Menu ...............................29
5.2 DMZ Configuration.........................................................31
5.3 Virtual Servers Configuration........................................34
5.4 Port Forwarding Configuration .....................................37
5.5 Special Applications Configuration................................40
5.6 Access Control Configuration.........................................43
5.6.1Workgroup Access Configuration.............................45
5.6.2Packet Filter Table Configuration ............................47
5.7 Dynamic DNS Configuration..........................................49
6. DIAL PLAN SET UP......................................................53
6.1 Concepts............................................................................53
6.1.1The Voice Port.............................................................53
6.1.2The dial plan...............................................................54
6.2 Web Browser Configuration ...........................................56
iii

7. CONFIGURATION EXAMPLES (USE CONSOLE
OR TELNET COMMANDS)..............................................68
7.1 The default dial-plans......................................................68
7.2 ITG to ITG in the Static IPAddress Environment........70
7.3 ITG to ITG in the Dynamic IPAddress Environment..75
7.4 PBX related issues............................................................79
7.4.1CPTone Detection ......................................................79
7.4.2Call Security................................................................79
iv

1.ABOUT THIS GUIDE
This Guide uses VG400R as a general example and contains
the following information:
Start Up Preparation: This chapter illustrates how to prepare
for the Internet Voice Gateway (VG) set up through console
interface or network interface.
WAN Configuration: You will learn how to set up IP address
and related configuration for your VG-400R in WAN side
environments such as static IP address, dynamic IP address.
LAN Configuration: You will learn how to set up IP address
and related configuration for your VG-400R in LAN side
environments such as static IP address, DHCP IP address.
Advanced Features: You will learn how to set up advance
features for LAN access management and DDNS configuration
for your VG-400R.
Dial Plan Setup: We will provide necessary procedure to guide
you step by step for a typical dial plan set up.
Configuration Example: This chapter shows you how to use
the default settings to start up your first call. Examples will be
given to show you how an VG may be working with telephony
devices such as PBXs and phone sets.
L
Hint
Bypass the Advanced Features chapter if you do
not want to do any LAN access management.
1.1 Before Start up
Before setting up your VG-400R the first time, you are required
to have the following:
1

 A PC that may run a web browser program such as
Netscape, Internet Explorer, etc.
 A 10/100 BaseTX Cat. 5 Ethernet LAN cable with RJ-45
connector.
 A console cable, where you may find it in the ITG package
(for 4/8xxR).
And later on, you are required to get familiar with your
environment, your TCP/IP network and your phone systems.
1.2 Notation Conventions (for console or telnet
setting)
This document uses the following conventions:
 Examples that contain system prompts denote interactive
sessions, indicating that the user enters commands at the
prompt.
 Different type styles and characters are used. These
serve a variety of purposes as described below:
Convention Description
boldface Commands and keywords are in
boldface.
Bold Arial User input (anything you are expected to
type in) is set in bold Arial.
italic Arguments for which you supply values.
[ ] Elements in square brackets are optional.
{ x | y | z } Alternative but required elements are
grouped in braces ({ }) and separated by
vertical bars ( | ).
[ x | y | z ] Optional alternative keywords are
grouped in brackets ([ ]) and separated by
vertical bars ( | ).
2

“string” A non-quoted set of characters. Do not
use quotation marks around the string or
the string will include the quotation marks.
<key> A key on the VT-100 terminal or terminal
emulator. For example <Enter> denotes
the Enter key.
3

2.START UP PREPARATION
This chapter shows you how to prepare for the VG-400R set
up for your network and/or Internet. We will focus on the web
browser usage.
Since the VG-400R comes with two default IP addresses, one
is for LAN side that is “192.168.0.1” and the other is for WAN
side that is “172.16.0.1”. You may use any PC to connect to
the LAN port of VG-400R, and then follow the steps below:
1) Set up the PC with an IP address in the “192.168.0.x” IP
domain, say, “192.168.0.2” with subnet mask address
“255.255.255.0” or choose “Obtain an IP address
automatically”
2) Start up the browser. In the address field, key in the
address http://192.168.0.1. The pop-up screen should
appear and prompt for user name and password. The
default values are:
User name: eitg (all lower case)
Password: 123
Now you are ready to perform the Network configuration set
up described in the next chapter.
4

3.WAN CONFIGURATION
We will show you the basic steps for a typical VG-400R
connection in various environments. It includes static IP
address environment and dynamic IP address environment.
3.1 Static IP Address Environment
There are several typical static IP address environment where
the following procedure may apply, such as popular
broadband application with ADSL or Cable network.
Run Web Browser such as Netscape or Internet Explorer.
Set
the address field to 192.168.0.1, type in the enter key, then
VG-400R will respond with the following page.
5

Enter eitg in “User Name” field and 123 in “Password” field
Then select “OK”, VG-400R will show the “Main Menu” as
follows:
6