YOKOGAWA SL1000 User manual

User’s
Manual SL1000
Input Module
IM 720120-51E
7th Edition

1
IM 720120-51E
Thank you for purchasing the SL1000 High-Speed Data Acquisition Unit. This user’s manual explains
the functions and operating procedures of the SL1000 Acquisition Software. To ensure correct use,
please read this manual thoroughly before beginning operation.
Keep this manual in a safe place for quick reference in the event a question arises. This manual will
come in handy when you are unsure of how to operate the product.
List of Manuals
The following manuals, including this one, are provided as manuals for the SL1000. Please read all of
them.
Manual Title Manual No. Description
SL1000
High-Speed Data Acquisition Unit
User’s Manual
IM 720120-01E Explains all functions and procedures of the SL1000
excluding the communication functions.
SL1000 Acquisition Software
User’s Manual
IM 720120-61E Explains all functions and procedures of the
Acquisition Software used to configure and control
the SL1000.
SL1000 Input Module
User’s Manual
IM 720120-51E This manual. Explains the specifications of the input
modules that can be installed in the SL1000.
Precautions Concerning the Modules IM 701250-04E The manual explains the precautions concerning the
modules.
701992 Xviewer Install Manual IM 701992-02E This manual explains how to install the Xviewer*
setup software.
SL1000
High-Speed Data Acquisition Unit
IM 720120-92 Document for China
The “E” in the manual numbers are the language codes.
* The Xviewer user’s manual is included in the Xviewer help.
Contact information of Yokogawa offices worldwide is provided on the following sheet.
Document No. Description
PIM 113-01Z2 List of worldwide contacts
Notes
• The contents of this manual are subject to change without prior notice as a result of continuing
improvements to the instrument’s performance and functions. The figures given in this manual may
differ from those that actually appear on your screen.
• Every effort has been made in the preparation of this manual to ensure the accuracy of its
contents. However, should you have any questions or find any errors, please contact your nearest
YOKOGAWA dealer.
• Copying or reproducing all or any part of the contents of this manual without YOKOGAWA’s
permission is strictly prohibited.
• The TCP/IP software of this product and the document concerning the TCP/IP software have been
developed/created by YOKOGAWA based on the BSD Networking Software, Release 1 that has
been licensed from University of California.
7th Edition: October 2017 (YMI)
All Rights Reserved, Copyright © 2007 Yokogawa Electric Corporation
All Rights Reserved, Copyright © 2012 Yokogawa Test & Measurement Corporation

2IM 720120-51E
Trademarks
• Microsoft, Windows, Windows XP, Windows Vista, Windows 7, and Windows 8 are either registered
trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
• Adobe and Acrobat are trademarks of Adobe Systems Incorporated.
• GIGAZoom ENGINE are pending trademark of Yokogawa Electric Corporation.
• For purposes of this manual, the ® and TM symbols do not accompany their respective registered
trademark names or trademark names.
• Other company and product names are registered trademarks or trademarks of their respective
holders.
Revisions
• 1st Edition: December 2007
• 2nd Edition: September 2013
• 3rd Edition: June 2014
• 4th Edition: October 2015
• 5th Edition: March 2016
• 6th Edition: July 2017
• 7th Edition: October 2017

3
IM 720120-51E
Conventions Used in This Manual
Unit
k: Denotes 1000. Example: 100 kS/s (sample rate)
K: Denotes 1024. Example: 720 KB (file size)
Notes and Cautions
The notes and cautions in this manual are categorized using the following symbols.
Improper handling or use can lead to injury to the user or damage to the
instrument. This symbol appears on the instrument to indicate that the user must
refer to the user’s manual for special instructions. The same symbol appears
in the corresponding place in the user’s manual to identify those instructions.
In the manual, the symbol is used in conjunction with the word “WARNING” or
“CAUTION.”
WARNING Calls attention to actions or conditions that could cause serious or fatal injury to
the user, and precautions that can be taken to prevent such occurrences.
CAUTION Calls attentions to actions or conditions that could cause light injury to the user
or damage to the instrument or user’s data, and precautions that can be taken to
prevent such occurrences.
French
AVERTISSEMENT Attire l’attention sur des gestes ou des conditions susceptibles
de provoquer des blessures graves (voire mortelles), et sur les
précautions de sécurité pouvant prévenir de tels accidents.
ATTENTION Attire l’attention sur des gestes ou des conditions susceptibles de
provoquer des blessures légères ou d’endommager l’instrument ou les
données de l’utilisateur, et sur les précautions de sécurité susceptibles
de prévenir de tels accidents.
Note
Calls attention to information that is important for proper operation of the
instrument.

4IM 720120-51E
Contents
List of Manuals .....................................................................................................................................1
Conventions Used in This Manual........................................................................................................3
1 High-Speed10MS/s,12-BitIsolationModule(701250)Specications ..........................5
2 High-Speed10MS/s,12-BitIsolationModule(720250)Specications ..........................7
3 High-Speed High-Resolution 1 MS/s, 16-Bit Isolation Module (701251) Specications..9
4 High-Speed10MS/s,12-BitNon-IsolationModule(701255)Specications.................11
5 High-Voltage 100 kS/s, 16-Bit Isolation Module (with RMS) (701267)Specications ...12
6 High-Voltage 1 MS/s, 16-Bit Isolation Module (with AAF, RMS) (720268)
Specications.................................................................................................................14
7 Universal (Voltage/Temp.) Module (701261) /Universal (Voltage/Temp.) Module (with
AAF)(701262)Specications ........................................................................................16
8 Temperature,HighPrecisionVoltageIsolationModule(701265)Specications...........18
9 Temperature, High Precision Voltage Isolation Module (low noise) (720266)
Specications.................................................................................................................20
10 StrainModule(NDIS)(701270)Specications ..............................................................22
11 StrainModule(DSUB,Shunt-Cal)(701271)Specications...........................................24
12 Acceleration/VoltageModule(withAAF)(701275)Specications .................................26
13 FrequencyModule(701281)Specications...................................................................28
14 FrequencyModule(720281)Specications...................................................................32
15 High-Speed100MS/s,12-BitIsolationModule(720210and720211)Specications...36
16 BasicDeningEquationofStrain ..................................................................................38
17 Shunt Calibration of the Strain Module ..........................................................................39
18 Measurement Principles (Measurement Method and Update Rate) of the Frequency
Module ...........................................................................................................................43
Appendix1 High-Voltage100kS/s,16-BitIsolationModule(withRMS)(701260)Specications ...45
Appendix2 FrequencyModule(701280)Specications...................................................................47

5
IM 720120-51E
1 High-Speed 10 MS/s, 12-Bit Isolation Module
(701250) Specifications
Item Specifications
Standard operating conditions Temperature: 23 ±5°C
Humidity: 20 to 80% RH
After a 30-minute warm-up and after calibration
Number of input channels 2
Input coupling AC, DC, and GND
Maximum sample rate 10 MS/s
Input format Isolated unbalanced
Frequency characteristics1
(−3dBpointwhensinewaveof
amplitude 60 % of range is input)
DC to 3 MHz
Voltage-axis range setting 50 mV range to 200 V range (1-2-5 steps) (when using 1:1 probe attenuation)
Maximum input voltage
(at a frequency of 1 kHz or less)
Combined with the 700929(10:1), 702902(10:1), or 701947(100:1):2
600 V (DC+ACpeak)
Combined with the 701901+701954 (1:1):4
200 V (DC+ACpeak) (as a value that meets the safety standard)
250 V (DC+ACpeak) (maximum allowable voltage, as a value that does not damage the
instrument when applied)
Direct input (cable that does not comply with the safety standards):6
42 V (DC+ACpeak)
Maximum rated voltage to earth
Between input and case
Between each input
(at a frequency of 1 kHz or less)
Working voltage of safety standard
In combination with 700929 (10:1)/702902 (10:1)/701947 (100:1),3or in combination with
701901+701954 (1:1):5
400 Vrms (measurement category Other (O)), 300 Vrms (CAT II)
Direct input (cable that does not comply with the safety standards):7
42 V (DC+ACpeak) (CAT II, 30 Vrms)
Vertical (voltage) axis accuracy
DC accuracy1
50 mV range to 200 V range: ±(0.5% of range)
Input connector BNC connector (isolated type)
Input impedance 1MΩ±1%,approx.35pF
−3dBpointwhenACcoupled
low frequency attenuation point
10 Hz or less (1 Hz or less when using the 700929 or 702902, 0.1 Hz or less when using the
701947)
Common mode rejection ratio 80 dB (50/60 Hz) or more (typical value8)
Residual noise level
(Input section shorted)
±400 µV or ±0.6% of range whichever is greater (typical value8)
Withstand voltage 2300 Vrms for 2 seconds (across each terminal and earth) (60 Hz)
Insulation resistance 500VDC,10MΩormore(acrosseachinputterminalandearth)
A/D conversion resolution 12 bit (1500 LSB/range)
Temperature coefficient Zero point: 50 mV range to 200 V range: ±(0.05% of range)/°C (typical value8)
Gain: ±(0.02% of range)/°C (typical value8)
Bandwidth limit Select from Full, 500 kHz, 50 kHz, 5 kHz, and 500 Hz
Cut-off characteristics: −18dB/OCT(typicalvalue8)
Probe attenuation setting Voltage probe: 1:1, 10:1, 100:1, 1000:1
Current probe: 1 A:1 V, 10 A:1 V (for the 701932/701933), 100 A: 1 V (for the 701930/701931)
Clamp-on probe: 1 A:10 mV (for the 720930), 1 A: 2.5 mV (for the 720931)

6IM 720120-51E
Item Specifications
Compatible probes/cables Voltage probe: Recommended
700929 (10:1 safety probe), 20 to 45 pF: For measuring 600 V (DC+ACpeak) or less
702902 (10:1 safety probe), 25 to 40 pF: For measuring 600 V (DC+ACpeak) or less
701947 (100:1 safety probe), 15 to 45 pF: For measuring 600 V (DC+ACpeak) or less
Current probe (power can be supplied from the SL1000 Unit, Option)
701930 (150 A), 701931 (500 A), 701932 (30 A), 701933 (30 A)
Clamp-on probe
720930 (50 A), 720931 (200 A)
High voltage differential probe (connect the GND cable provided with the probe to the SL1000
Unit case)
700924 (1000:1, 100:1/1400 V (DC+ACpeak)): For measuring 1400 V (DC+ACpeak) or less
Connection cable (for high voltage 1:1)
701901 (isolated type BNC-safety alligator clip adapter ×2: For measuring 200 V
(DC+ACpeak) or less), 701954 (alligator clip (dolphin type) red/black 2-piece set) is required
separately
Connection cable (for low voltage 1:1)
366926 (non-isolated type BNC-alligator clip ×2: For measuring low voltage less than or
equal to 42 V (DC+ACpeak))
1 Value measured under standard operating conditions.
Combined with the 700929, 702902, or 701947
2
3
Combined with the 701901+701954
Direct input (cable that does not comply with the safety standards)
6
7
4
5
H
L
700929
702902
701947
H
L
BNC
H
L
701901 701954
8 The typical value is a representative or standard value. It is not strictly warranted.
1 High-Speed 10 MS/s, 12-Bit Isolation Module (701250) Specifications

7
IM 720120-51E
2 High-Speed 10 MS/s, 12-Bit Isolation Module
(720250) Specifications
Item Specifications
Standard operating conditions Temperature: 23 ±5°C
Humidity: 20 to 80% RH
After a 30-minute warm-up and after calibration
Number of input channels 2
Input coupling AC, DC, and GND
Maximum sample rate 10 MS/s
Input format Isolated unbalanced
Frequency characteristics1
(−3dBpointwhensinewave
of amplitude 60 % of range is
applied)
DC to 3 MHz
Voltage-axis range setting 50 mV range to 200 V range (1-2-5 steps) (when using 1:1 probe attenuation)
Maximum input voltage
(at a frequency of 1 kHz or less)
Combined with the 700929(10:1), 702902(10:1), or 701947(100:1):2
800 V (DC+ACpeak)
Combined with the 701901+701954 (1:1):4
200 V (DC+ACpeak) (as a value that meets the safety standard)
250 V (DC+ACpeak) (maximum allowable voltage, as a value that does not damage the
instrument when applied)
Direct input (cable that does not comply with the safety standards):6
42 V (DC+ACpeak)
Maximum rated voltage to earth
Between input and case
Between each input(at a
frequency of 1 kHz or less)
Working voltage of safety standard
In combination with 700929 (10:1)/702902 (10:1)/701947 (100:1),3or in combination with
701901+701954 (1:1):5
400 Vrms (CAT II)
Direct input (cable that does not comply with the safety standards):7
42 V (DC+ACpeak) (CAT II, 30 Vrms)
Vertical (voltage) axis accuracy
DC accuracy1
±0.5 % of range
Input connector BNC connector (isolated type)
Input impedance 1MΩ±1%,approx.35pF
−3dBpointwhenACcoupled
low frequency attenuation point
10 Hz or less (1 Hz or less when using the 700929 or 702902, 0.1 Hz or less when using the
701947)
Common mode rejection ratio 80 dB (50/60 Hz) or more (typical value8)
Residual noise level
(Input section shorted)
±400 µV or ±0.06 div whichever is greater (typical value8)
Withstand voltage 2300 Vrms for 2 seconds (across each terminal and earth)
Insulation resistance 500VDC,10MΩormore(acrosseachinputterminalandearth)
A/D conversion resolution 12 bit (150 LSB/div)
Temperature coefficient Zero point: ±(0.05% of range)/°C (typical value8)
Gain: ±(0.02% of range)/°C (typical value8)
Bandwidth limit Select from Full, 500 kHz, 50 kHz, 5 kHz, and 500 Hz
Cut-off characteristics: −18dB/OCT(typicalvalue8)
Probe attenuation setting Voltage probe: 1:1, 10:1, 100:1, 1000:1
Current probe: 1 A:1 V, 10 A:1 V (for the 701932/701933), 100 A: 1 V (for the 701930/701931)
Clamp-on probe: 1 A:10 mV (for the 720930), 1 A: 2.5 mV (for the 720931)

8IM 720120-51E
Item Specifications
Compatible probes/cables Voltage probe: Recommended
700929 (10:1 safety probe), 20 to 45 pF: For measuring 600 V (DC+ACpeak) or less
702902 (10:1 safety probe), 25 to 40 pF: For measuring 600 V (DC+ACpeak) or less
701947 (100:1 safety probe), 15 to 45 pF: For measuring 600 V (DC+ACpeak) or less
Current probe (power can be supplied from the SL1000 unit, Option)
701930 (150 A), 701931 (500 A), 701932 (30 A), 701933 (30 A), 701917(5A), 701918(5A)
Clamp-on probe
720930 (50 A), 720931 (200 A)
High voltage differential probe (connect the GND cable provided with the probe to the SL1000
unit case)
700924 (1000:1, 100:1/1400 V (DC+ACpeak)): For measuring 1400 V (DC+ACpeak) or less
Connection cable (for high voltage 1:1)
701901 (isolated type BNC-safety alligator clip adapter ×2: For measuring 200 V
(DC+ACpeak) or less), 701954 (alligator clip (dolphin type) red/black 2-piece set) is required
separately
Connection cable (for low voltage 1:1)
366926 (non-isolated type BNC-alligator clip ×2: For measuring low voltage less than or
equal to 42 V (DC+ACpeak))
1 Value measured under standard operating conditions.
Combined with the 700929, 702902, or 701947
2
3
Combined with the 701901+701954
Direct input (cable that does not comply with the safety standards)
6
7
4
5
H
L
700929
702902
701947
H
L
BNC
H
L
701901 701954
8 The typical value is a representative or standard value. It is not strictly warranted.
2 High-Speed 10 MS/s, 12-Bit Isolation Module (720250) Specifications

9
IM 720120-51E
3 High-Speed High-Resolution 1 MS/s, 16-Bit
Isolation Module (701251) Specifications
Item Specifications
Standard operating conditions Temperature: 23 ±5°C
Humidity: 20 to 80% RH
After a 30-minute warm-up and after calibration
Number of input channels 2
Input coupling AC, DC, and GND
Maximum sample rate 1 MS/s
Input format Isolated unbalanced
Frequency characteristics1
(−3dBpointwhenasinewaveof
amplitude 60 % of range is input)
50 mV range to 200 V range: DC to 300 kHz
20 mV range and 10mV range: DC to 200 kHz
Voltage-axis range setting 1 mV range to 20 V range (1-2-5 steps) (when using 1:1 probe attenuation)
Maximum input voltage
(at a frequency of 1 kHz or less)
Combined with the 700929 (10:1), 702902 (10:1), or 701947 (100:1):2
600 V (DC+ACpeak)
Combined with the 701901+701954 (1:1):4
140 V (DC+ACpeak)
Direct input (cable that does not comply with the safety standards):6
42 V (DC+ACpeak)
Maximum rated voltage to earth
Between input and case
Between each input(at a
frequency of 1 kHz or less)
Working voltage of safety standard
In combination with 700929 (10:1)/702902 (10:1)/701947 (100:1),3or in combination with
701901+701954 (1:1):5
400 Vrms (measurement category Other (O)), 300 Vrms (CAT II)
Direct input (cable that does not comply with the safety standards):7
42 V (DC+ACpeak) (CAT II, 30 Vrms)
Vertical (voltage) axis accuracy
DC accuracy1
50 mV range to 200 V range: ±(0.25% of range)
20 mV range: ±(0.3% of range)
10 mV range: ±(0.5% of range)
Input connector BNC connector (isolated type)
Input impedance 1MΩ±1%,approx.35pF
−3dBpointwhenACcoupled
low frequency attenuation point
1 Hz or less (0.1 Hz or less when using the 700929 or 702902, 0.01 Hz or less when using
the 701947)
Common mode rejection ratio 80 dB (50/60 Hz) or more (typical value8)
Residual noise level
(Input section shorted)
±100 µV or ±0.1% of range whichever is greater (typical value8)
Withstand voltage 2300 Vrms for 2 seconds (across each terminal and earth) (60 Hz)
Insulation resistance 500VDC,10MΩormore(acrosseachinputterminalandearth)
A/D conversion resolution 16 bit (24000 LSB/range)
Temperature coefficient Zero point: 50 mV range to 200 V range: ±(0.02% of range)/°C (typical value8)
20 mV range: ±(0.05% of range)/°C (typical value8)
10 mV range: ±(0.10% of range)/°C (typical value8)
Gain: 10 mV range to 200 V range: ±(0.02% of range)/°C (typical value8)
Bandwidth limit Select from Full, 40 kHz, 4 kHz, and 400 Hz
Cut-off characteristics: −12dB/OCT(typicalvalue8)
Probe attenuation setting Voltage probe: 1:1, 10:1, 100:1, 1000:1
Current probe: 1 A:1 V, 10 A:1 V (for the 701932/701933), 100 A: 1 V (for the 701930/701931)
Clamp-on probe: 1 A:10 mV (for the 720930), 1 A: 2.5 mV (for the 720931)