Young America Kudos SSC 1600 User manual

2

x 9JGPEJKNFKUCDNGVQRWNNVQCUVCPFKPIRQUKVKQPUGVVJGOCVVTGUUVQVJGNQYGUV
RQUKVKQPCPFTGOQXGDWORGTRCFUNCTIGVQ[UCPFQVJGTQDLGEVUVJCVEQWNFUGTXG
CUUVGRUHQTENKODKPIQWV
x 9JGPCEJKNFKUCDNGVQENKODQWVQTTGCEJGUVJGJGKIJVQHKPEOVJGETKD
UJCNNPQNQPIGTDGWUGF
x &1016RNCEGCETKDPGCTCYKPFQYYJGTGEQTFUHTQODNKPFUQTFTCRGUOC[
UVTCPINGCEJKNF
x 6QTGFWEGVJGTKUMQH5+&5RGFKCVTKEKCPUTGEQOOGPFJGCNVJ[KPHCPVUDGRNCEGFQP
VJGKTDCEMUVQUNGGRWPNGUUQVJGTYKUGCFXKUGFD[[QWTRJ[UKEKCP
x 6QJGNRRTGXGPVUVTCPIWNCVKQPVKIJVGPCNNHCUVGPGTU#EJKNFECPVTCRRCTVUQHVJG
DQF[QTENQVJKPIQPNQQUGHCUVGPGTU
x 5VTKPIUECPECWUGUVTCPIWNCVKQP&QPQVRNCEGKVGOUYKVJCUVTKPICTQWPFC
EJKNFUPGEMUWEJCUJQQFUVTKPIUQTRCEKHKGTEQTFU&QPQVUWURGPFUVTKPIUQXGT
CETKDQTCVVCEJUVTKPIUVQVQ[U
x $GHQTGGCEJWUCIGQTCUUGODN[KPURGEVETKDHQTFCOCIGFJCTFYCTGNQQUGLQKPVU
OKUUKPIRCTVUQTUJCTRGFIGU&1016WUGETKDKHCP[RCTVUCTGOKUUKPIQTDTQMGP
%QPVCEV[QWTFGCNGTQTYTKVGVQ;QWPI#OGTKEC21$QZ5VCPNG[VQYP8#
HQTTGRNCEGOGPVRCTVUCPFKPUVTWEVKQPCNNKVGTCVWTGKHPGGFGF
x &1016UWDUVKVWVGRCTVU7UGQPN[DQNVUQTRCTVUUWRRNKGFD[OCPWHCEVWTGTQT
RCTVUQHEQORCTCDNGSWCNKV[CPFGSWCNFKOGPUKQPU&QPQVCNNQYGPFUQHDQNVUQT
UJCTRGFIGUVQDGGZRQUGF
x (QNNQYYCTPKPIUQPCNNRTQFWEVUKPCETKD
x +HTGHKPKUJKPIWUGCPQPÄVQZKEHKPKUJURGEKHKGFHQTEJKNFTGPURTQFWEVU
x +PHCPVUECPUWHHQECVGQPUQHVDGFFKPI0GXGTCFFCRKNNQYEQOHQTVGTQTRCFFKPI
0GXGTRNCEGCFFKVKQPCNRCFFKPIWPFGTCPKPHCPV
x +PHCPVUECPUWHHQECVGKPICRUDGVYGGPETKDUKFGUCPFCOCVVTGUUVJCVKUVQQUOCNN
x 0GXGTWUGRNCUVKEUJKRRKPIDCIUQTQVJGTRNCUVKEHKNOCUOCVVTGUUEQXGTUDGECWUG
VJG[ECPECWUGUWHHQECVKQP
x &QPQVCNNQYEJKNFVQETCYNQTRNC[WPFGTPGCVJETKD
x 7UGECWVKQPYJGPCXCRQTK\GTKUKPWUG#NYC[UCKOVJGXCRQTUVGCOCYC[HTQO
VJGETKDCUYGNNCUCYC[HTQOCP[QVJGTYQQFHWTPKVWTGKVGO
x 6JGETKDOWUVDGHWNN[CUUGODNGFRTKQTVQWUG
x 4GCFCNNKPUVTWEVKQPUDGHQTGCUUGODNKPIETKD-''2+05647%6+105(14
(7674'75'
x %#76+10#P[OCVVTGUUWUGFKPVJKUETKDOWUVDGCVNGCUVÄ´ 
D[Ä´ YKVJCVJKEMPGUUQHPQNGUUVJCPKPEJGUCPFPQVGZEGGFKPIKPEJGU
9JGP%QPXGTVKPIVQC6QFFNGT$GF

x 0'8'4WUGDGFYKVJEJKNFTGPWPFGTOQPVJUQHCIG
x 6JGOCZKOWOYGKIJVQHVJGKPVGPFGFWUGTUJCNNPQVDGITGCVGTVJCPNDMI
!9#40+0): (#+.74'61(1..196*'5'9#40+0)5#0&6*'
#55'/$.;+05647%6+105%17.&4'57.6+05'4+175+0,74;14&'#6*

3
The crib illustrations in these instructions are generic in nature. The crib you have purchased
may not look like the ones illustrated; however, they all assemble in the same manner.
Identifying the Parts
2 Crib Ends Mattress Platform
2 Base Rails
2 Crib Sides
Base

4
4 Connector Bolts
2 3/8” (1/4” x 20 thread)
18 Connector Bolts
2” (1/4 x 20 thread)
Identifying the Hardware
Identify the hardware included using the illustrations below
8 Connector Bolts
3 1/2” (1/4” x 20 thread)
6 Locater Pins
4 Mattress Brackets
with Bolts
2 Allen Wrenches

5
Crib Assembly
NOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
Attached to the mattress platform is a sleeve to store the instruction booklet.
After assembly is complete, return this instruction booklet to the sleeve for future
reference.
This crib conforms to the ASTM International and the CPSC-Consumer Product Safety
Commission guidelines for product safety. Please adhere to the guidelines in this book-
let for assembly, operation and maintenance.
Note the recommendations below:
x Power tools are not recommended for assembly.
x Give yourself plenty of room to work.
x Due to the size of this bed, it must be assembled in the space it will occupy.
x The assembly will take two people to complete.
x Layout all the hardware and make sure that the proper length bolts are used in the
designated areas.
x Do not substitute hardware. If an item is missing or damaged contact Stanley
Furniture Company immediately for replacement. Inspect all component parts and
hardware prior to beginning the assembly process.
x Make sure all fasteners are tight.
x Above all, take your time and read the instructions carefully.
Tools required for Assembly:
x Flathead Screwdriver
x Allen Wrenches (provided)
This Crib is equipped with these additional features:
Barrel Nut Retainer Bracket— The Bracket is located on each end of the Base Rails.
It is designed to prevent loss of Barrel Nuts during assembly and disassembly of
crib.
Bolt Retainer Sleeve—The Retainer Sleeves are located where Connector
Bolts are used to assemble the crib. It is designed to prevent loss of the Con-
nector Bolts after crib is disassembled. The Bolt Retainer Sleeves are perma-
nently installed at the factory.

6
Attaching the Crib Base Rails
Step 1:
x Using a Flathead Screwdriver, align the slots in the Barrel Nuts with the holes for
the connector bolts located in the Base Rail . See Figure 1a.
x Align the holes in the Base Rail with the holes in the Crib Ends and insert (4) 3 1/2”
connector bolts from the outside of the Crib Ends. Make sure the Brackets attached
to the Base Rail are facing the inside of the Crib. See Figure 1b.
x Repeat Steps for opposite Side Rail.
x Do not completely tighten the connector bolts at this time.
Figure 1a.
Figure 1b.
Figure 1a.
Barrel Nuts
Figure 1b. Figure 1b.
Step 2:
x Install (6) Locater Pins.
x Locate the threaded insert in the top edge of each
Base Rail and insert a Locater Pin. Tighten by
hand. See Figure 2a.
x Locate the top inserts in each of the Crib Ends and
insert a Locater Pin. See Figure 2b.
Figure 2b.
Figure 2b. Figure 2a.
Figure 2a.

7
Attaching the Crib Base
Step 3:
x Gently lay the assembled Crib Ends and Side Rails on its side on a padded surface.
x Align the Base with the bottom of the assembled components. The connector holes located in the
Base will align with the inserts located in the Crib Ends and Rails. See Figure 3a.
x Locate (10) 2” Connector Bolts. Insert the Connector Bolts into the aligned holes. See Figure 3b.
x Gently tighten the Connector Bolts in a Clockwise motion with the Allen Wrench provided. Do
not completely tighten at this time. See Figure 3c.
x Return partially assembled Crib to the upright position. See Figure 3d.
Figure 3a.
Crib Base
Crib Ends and Rails
Figure 3b.
Figure 3c.
Figure 3d.

8
Attaching the Crib Side
Step 4:
x Position (1) Crib Side, as shown in Figure
4a, by aligning the Locater Pin on the top
edge of the Base Rail with the hole in the
bottom rail of the Crib Side.
x Gently spread the top of the Crib Ends to
allow the Locater Pins in the Crib Ends to
engage the holes in the ends of the Crib
Side top rail. See Figure 4b.
x Insert (4) 2” Connector Bolts into the holes
that are in the end uprights of the Crib Side.
Loosely attach the Crib Side to the Crib
Ends using the provided wrench. Do not
tighten the bolts at this time. See Figure 4c.
x Figure 4d is how your Crib should look at
this point.
Figure 4a.
Figure 4b.
Figure 4a. Figure 4b.
Figure 4c.
Figure 4c.
Figure 4d.

9
Attaching the Mattress Platform Brackets
Step 5:
x Locate the (4) Mattress Platform Brackets with attached assembly bolts as shown in Figure 5a. Deter-
mine the high or low position of the mattress foundation (Figure 5a.). Attach the brackets on both the
left and right end section in the same height location. (This is very important to keep the foundation
level and your child safe).
x Attach the (4) brackets and tighten bolts using the wrench provided. See Figure 5b.
x Make sure the brackets are straight and perpendicular to the crib uprights.
High Position
Low Position
Figure 5a. Figure 5a.
Figure 5b.

10
Attaching the Mattress Platform
Step 6:
x Place the Mattress Platform into the support brackets. (Before inserting bolts, make sure the instruc-
tion holder and the warning label are facing up and readable as shown in Figure 6a.
x After the Mattress Platform is in place, use the (4) 2 3/8” connector bolts to attach the Mattress Plat-
form to the support brackets. Insert each bolt in place and start the bolt into the bracket threads. See
Figure 6a. Do not completely tighten the Mattress Platform bolts at this time.
x Figure 6b is how your crib should look with Warning labels facing the front of the crib.
x When child is able to pull to a standing position, set the mattress platform to the lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out.
Figure 6a. Figure 6a.
Figure 6b.

11
Attaching the Opposite Crib Side
Step 7:
x Attach the remaining Crib Side. See Figure 7a.
x Refer to Page 8 and follow Step 4.
x Tighten all Crib Side, Mattress Platform, Base Rail, and Crib Ends bolts at this time.
x After the crib is assembled recheck all assembly bolts and make sure that each is securely tightened
using the provided wrench.
Figure 7a.
Figure 7b.
Completed Crib Assembly

12
Final Step in Crib Assembly
Step 8: (The final and most important) Checklist.
x Inspect the crib once again to assure that all bolts are tight and that no hardware is missing. (if you
have missing hardware, contact Stanley Furniture immediately for replacement and do not use the
crib until the new hardware arrives).
x Do not place the crib near a window where the child may have access to window coverings, cords or
draperies as these articles pose a strangulation hazard.
x Replace the instructions in the holder provided. KEEP THE INSTRUCTIONS WITH THE CRIB.
x Install the crib mattress.
x Follow all the warnings on the use of this crib and all products in the crib.
x CAUTION: Any mattress used in this crib must be at least 27-1/4” by 51-5/8”
with a thickness of no less than 4 inches and not exceeding 6 inches.

13
Cleaning:
Mix together a mild solution of gentle dishwashing liquid and water, apply to the crib sur-
face using a soft clean cloth lightly dampened in the solution. Rinse with clear water, us-
ing a lightly dampened, soft clean cloth, then dry all surfaces thoroughly with a dry cloth.
NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COURSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
Storage:
A permanent storage pouch is attached to the mattress platform for the storage of the as-
sembly instructions. After completing the assembly process, you are advised to read and
be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAIN-
TENANCE notices contained in these instructions. Do not place excess hardware in the
storage pouch as it could present a danger to a child if retrieved and could also damage
the mattress. When storing the crib, use CAUTION as temperature changes and hu-
midity could be harmful to the crib. It is recommended that the crib be stored in a tem-
perature controlled environment.
Periodic Maintenance:
1. Periodically check to make sure all bolts and connections are fastened securely.
2. If you are missing a part or need a replacement part, do not substitute parts. Ask your
dealer for replacement parts or contact Customer Service at [phone].
3. The crib allows for 2 mattress heights. Move to the low position when the child can
pull up to a standing position. When the child reaches a height of 35” or can climb out
of the crib you should place the child in a youth or regular bed.
4. Save these instructions, in sleeve attached to the mattress platform, in the event you
disassemble the crib and need to reassemble it. These instructions will also be useful
in identifying replacement parts if needed at a future date.

14
Lowering the Mattress Platform
Steps to lower the mattress:
x Remove the mattress from the crib.
x Loosen the (4) bolts attaching the front Crib Side from the End Assembly. Note: Bolts will stay at-
tached to Crib Side. See Figure 9a.
x Gently spread the top of the Crib Ends to allow the Locater Pins in the Crib Ends to disengage the
holes in the ends of the Crib Side top rail. Lift up and remove the Crib Side. See Figure 9b.
x Loosen the (4) bolts attaching the Mattress Platform and remove the platform from the crib. Note:
Bolts will stay with Mattress Platform. See Figure 9c.
x Remove the platform brackets and place in the lower position. See Figure 9d.
x Refer to Step 6 on Page 10 for instruction to reassemble the crib.
x Check and securely tighten all assembly bolts with the provided wrench.
Higher location
Lower location
Figure 9a.
Figure 9b. Figure 9b.
Figure 9a.
Figure 9c. Figure 9d.

15
Converting Your Crib to a Daybed
Steps to Convert Crib to a Daybed:
x When converting to a Daybed the Mattress Platform must be in the lower position.
x Follow the instructions on page 14 for lowering the Mattress Platform. Do not reattach the Crib Side.
x Remove the (3) exposed Locater Pins from the Crib Ends and the Base Rail.
x Store the Locater Pins for future assembly of the crib. Do not place excess hardware in the storage
pouch as it could present a danger to a child if retrieved and could also damage the mattress.

16
Toddler Bed Conversion Kit item STK-3435 is
available as an option to convert the Stationary Side
Crib to a toddler bed. Contact your youngAmerica
dealer to purchase this item.
Accessories and Options