Young America SSC 1400 User manual

Model Number:
SSC 1400
Your little one will sleep securely in this youngAmerica Crib. Proper assembly will
ensure every effort has been made to design this crib with your baby's safety in
mind. It is certified to meet all safety guidelines established by ASTM International
and the CPSC-Consumer Product Safety Commission.
Thank you for purchasing a youngAmerica Crib. If you find that you are missing a
part or if a part is defective in any way, contact your youngAmerica retailer for as-
sistance.
Stationary Side Crib Assembly Instructions
IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY

2
!WARNING: FAILURE TO FOLLOW THESE WARNINGS AND THE
ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.
 When child is able to pull to a standing position, set the mattress to the lowest
position and remove bumper pads, large toys and other objects that could serve
as steps for climbing out.
 When a child is able to climb out or reaches the height of 35 in. (90 cm), the crib
shall no longer be used.
 DO NOT place a crib near a window where cords from blinds or drapes may
strangle a child.
 To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on
their backs to sleep, unless otherwise advised by your physician.
 To help prevent strangulation tighten all fasteners. A child can trap parts of the
body or clothing on loose fasteners.
 Strings can cause strangulation! Do not place items with a string around a
childs neck, such as hood strings or pacifier cords. Do not suspend strings over
a crib or attach strings to toys.
 Before each usage or assembly, inspect crib for damaged hardware, loose joints,
missing parts or sharp edges. DO NOT use crib if any parts are missing or broken.
Contact your dealer or write to Young America, PO Box 30, Stanleytown, VA 24168
for replacement parts and instructional literature if needed.
 DO NOT substitute parts. Use only bolts or parts supplied by manufacturer or
parts of comparable quality and equal dimensions. Do not allow ends of bolts or
sharp edges to be exposed.
 Follow warnings on all products in a crib.
 If refinishing, use a non−toxic finish specified for children’s products.
 Infants can suffocate on soft bedding. Never add a pillow, comforter or padding.
Never place additional padding under an infant.
 Infants can suffocate in gaps between crib sides and a mattress that is too small.
 Never use plastic shipping bags or other plastic film as mattress covers because
they can cause suffocation.
 Do not allow child to crawl or play underneath crib.
 Use caution when a vaporizer is in use. Always aim the vapor steam away from
the crib as well as away from any other wood furniture item.
 The crib must be fully assembled prior to use.
 Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR
FUTURE USE.
 CAUTION: Any mattress used in this crib must be at least 27−1/4˜
by 51−5/8˜ with a thickness of no less than 4 inches and not exceeding 6 inches.
When Converting to a Toddler Bed:
 NEVER use bed with children under 15 months of age.
 The maximum weight of the intended user shall not be greater than 50 lb (22.7kg).

3
The crib illustrations in these instructions are generic in nature. The crib you have purchased
may not look like the ones illustrated; however, they all assemble in the same manner.
Identifying the Parts
2 Crib Ends Mattress Platform
2 Base Rails 2 Crib Sides

4
4 Connector Bolts
2 3/8” (1/4” x 20 thread)
16 Connector Bolts
2” (1/4 x 20 thread)
2 Allen Wrenches
Identifying the Hardware
Identify the hardware included using the illustrations below
6 Locater Pins
4 Mattress Brackets
with Bolts

5
Crib Assembly
NOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.
Attached to the mattress platform is a sleeve to store the instruction booklet.
After assembly is complete, return this instruction booklet to the sleeve for future
reference.
This crib conforms to the ASTM International and the CPSC-Consumer Product Safety
Commission guidelines for product safety. Please adhere to the guidelines in this book-
let for assembly, operation and maintenance.
Note the recommendations below:
 Power tools are not recommended for assembly.
 Give yourself plenty of room to work.
 Due to the size of this bed, it must be assembled in the space it will occupy.
 The assembly will take two people to complete.
 Layout all the hardware and make sure that the proper length bolts are used in the
designated areas.
 Do not substitute hardware. If an item is missing or damaged contact Stanley
Furniture Company immediately for replacement. Inspect all component parts and
hardware prior to beginning the assembly process.
 Make sure all fasteners are tight.
 Above all, take your time and read the instructions carefully.
Tools required for Assembly:
 Allen Wrenches (provided)
This Crib is equipped with these additional features:
Bolt Retainer Sleeve—The Retainer Sleeves are located where Connector
Bolts are used to assemble the crib. It is designed to prevent loss of the Con-
nector Bolts after crib is disassembled. The Bolt Retainer Sleeves are perma-
nently installed at the factory.

6
See
Figure 2.
Attaching the Mattress Platform Brackets
Figure 2.
Enlarged
View
Wrench
Mattress
Bracket
Figure 1. End Assemblies
Higher locationLower location
Figure 3.
 Make sure the brackets are straight and
perpendicular to the crib uprights.
 When child is able to pull to a standing
position, set the mattress platform to the
lowest position and remove bumper pads,
large toys and other objects that could
serve as steps for climbing out.
Step 1:
 Locate the (4) Mattress Platform Brackets with
attached assembly bolts as shown in Fig. 1.
Determine the high or low position of the mat-
tress foundation (Fig. 3) and attach the brack-
ets on both the left and right end section in the
same height location. (This is very important
to keep the foundation level and your child
safe).
 Attach the (4) brackets and tighten bolts using
the wrench provided. See Figure 2.

7
Attaching the Crib Base Rail
Step 2:
 As shown in Fig. 4, align the holes in (1) of the Base Rails with the holes in the Crib
Ends and insert the connector bolts from the inside of the Base Rail.
 Loosely attach the Base Rail to the Crib Ends using (4) 2” connector bolts. Make sure
the Brackets attached to the Base Rail are facing the inside of the Crib.
 Secure the connector bolts just enough to hold the Base Rail in place using the provided
wrench.
See
Figure 4.
Figure 4.
Enlarged
View
 Install (3) Locater Pins, (1) in
the Base Rail and (1) in each
Crib End.
 Locate the threaded insert in
the top edge of the Base Rail
and insert a Locater Pin.
Tighten by hand. See Fig. 5.
 Locate the upper threaded in-
sert in each of the Crib Ends
and insert a Locater Pin. See
Fig. 6. (Make sure to insert
the Locater Pins on the same
side of the Crib Ends as the
attached Base Rail.)
See
Figure 5.
See Figure 6.
Figure 5.
Enlarged
View
Base Rail
Crib End Upper
Insert
Figure 6.
Enlarged
View
Threaded
Insert
Wrench
Locater
Pin

8
Attaching the Crib Side
Step 3:
 Position (1) Crib Side, as shown in Fig-
ure 7, by aligning the Locater Pin on
the top edge of the Base Rail with the
hole in the bottom rail of the Crib Side.
 Gently spread the top of the Crib Ends
to allow the Locater Pins in the Crib
Ends to engage the holes in the ends of
the Crib Side top rail. See Figure 8.
 Insert (4) 2” Connector Bolts into the
holes that are in the end uprights of the
Crib Side. Loosely attach the Crib
Side to the Crib Ends using the pro-
vided wrench. Do not tighten the bolts
at this time. See Figure 9.
 Tighten the connector bolts that attach
the Base Rail to the Crib Ends at this
time with the provided wrench. See Fig.
4 on Page 7.
 Attach the remaining Base Rail and Lo-
cater Pins following Step 2 on page 7.
Do not completely tighten Base Rail
bolts at this time.
 Figure 10 is how your Crib should
look at this point.
Figure 7.
Align Crib Side
Base Rail
Figure 7.
Enlarged View of
Crib Side alignment
Figure 8.
Figure 8.
Enlarged View of
Crib End - Crib Side
alignment
Locater Pin
Crib Side
Crib End
See
Figure 9.
Figure 9.
Enlarged View
Wrench
2” Bolt
Figure 10.
Assembled View
Fig. 8
Fig. 9

9
Attaching the Mattress Platform
Step 4:
 Place the Mattress Platform into the sup-
port brackets. (Before inserting bolts,
make sure the instruction holder and the
warning label are facing up and readable as
shown in Fig 12.
 After the Mattress Platform is in place, use
the (4) 2 3/8” connector bolts to attach the
Mattress Platform to the support brackets.
Insert each bolt in place and start the bolt
into the bracket threads. See Figure 11.
Do not completely tighten the Mattress
Platform bolts at this time.
 Fig. 12 is how your crib should look with
Warning labels facing the front of the crib.
Figure 12.
Assembled with mattress platform
Figure 11.
Enlarged view of bolt attachment
See
Figure 11.

10
Attaching the Opposite Crib Side
And Base Rail
Step 5:
 Attach the remaining Crib Side.
See Fig. 13.
 Refer to Step 3 on pages 8.
 Tighten all Crib Side, Mattress
Platform, and Base Rail bolts at
this time.
 After the Crib is assembled re-
check all assembly bolts and
make sure that each is securely
tightened using the provided
wrench.
Figure 13.
Remaining Assembly
Figure 14.
Completed
Assembly

11
Final Step in Crib Assembly
Step 6: (The final and most important) Checklist.
 Inspect the crib once again to assure that all bolts are tight and that no hardware is missing. (if you
have missing hardware, contact Stanley Furniture immediately for replacement and do not use the
crib until the new hardware arrives).
 Do not place the crib near a window where the child may have access to window coverings, cords or
draperies as these articles pose a strangulation hazard.
 Replace the instructions in the holder provided. KEEP THE INSTRUCTIONS WITH THE CRIB.
 Install the crib mattress.
 Follow all the warnings on the use of this crib and all products in the crib.
 CAUTION: Any mattress used in this crib must be at least 27-1/4” by 51-5/8”
with a thickness of no less than 4 inches and not exceeding 6 inches.

12
Cleaning:
Mix together a mild solution of gentle dishwashing liquid and water, apply to the crib sur-
face using a soft clean cloth lightly dampened in the solution. Rinse with clear water, us-
ing a lightly dampened, soft clean cloth, then dry all surfaces thoroughly with a dry cloth.
NO ABRASIVE CLEANERS, SCOURING PADS, STEEL WOOL OR COURSE RAGS
SHOULD BE USED TO CLEAN THIS FINE FURNITURE.
Storage:
A permanent storage pouch is attached to the mattress platform for the storage of the as-
sembly instructions. After completing the assembly process, you are advised to read and
be aware of all WARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAIN-
TENANCE notices contained in these instructions. Do not place excess hardware in the
storage pouch as it could present a danger to a child if retrieved and could also damage
the mattress. When storing the crib, use CAUTION as temperature changes and hu-
midity could be harmful to the crib. It is recommended that the crib be stored in a tem-
perature controlled environment.
Periodic Maintenance:
1. Periodically check to make sure all bolts and connections are fastened securely.
2. If you are missing a part or need a replacement part, do not substitute parts. Ask your
dealer for replacement parts or contact Customer Service at [phone].
3. The crib allows for 2 mattress heights. Move to the low position when the child can
pull up to a standing position. When the child reaches a height of 35” or can climb out
of the crib you should place the child in a youth or regular bed.
4. Save these instructions, in the sleeve attached to the mattress platform, in the event you
disassemble the crib and need to reassemble it. These instructions will also be useful
in identifying replacement parts if needed at a future date.

13
Locater Pin
Crib Side
Crib End
Lowering the Mattress Platform
Steps to lower the mattress:
 Remove the mattress from the crib.
 Loosen the (4) bolts attaching the front Base Rail.
You may have to position the Crib on its side for
easier access to the Side Rail bolts. See Figure 15.
 If the Crib is on its side return it to an upright po-
sition. Loosen the (4) bolts attaching the front
Crib Side. Note: Bolts will stay with Crib Side.
See Figure 16.
 Gently spread the top of the Crib Ends to allow
the Locater Pins in the Crib Ends to disengage the
holes in the ends of the Crib Side top rail. Lift up
and remove the Crib Side. See Figure 17.
 Loosen the (4) bolts attaching the Mattress Plat-
form and remove the platform from the crib.
Note: Bolts will stay attached to Mattress Plat-
form. See Figure 18.
 Remove the platform brackets and place in the
lower position. See Figure 19.
 Refer to Step 4 on Page 9 to reassemble the crib.
 Check and securely tighten all assembly bolts
with the provided wrench.
Figure 15.
Figure 17.
Figure 16.
Figure 18.
Higher location
Lower location
Figure 19.
Mattress bracket
Wrench
Wrench

14
Converting Your Crib to a Daybed
Steps to Convert Crib to a Daybed:
 When converting to a Daybed the Mattress Platform must be in the lower position.
 Follow the instructions on page 13 for lowering the Mattress Platform. Do not reattach the Crib Side.
 Remove the (3) exposed Locater Pins from the Crib Ends and the Base Rail.
 Store the Locater Pins for future assembly of the crib. Do not place excess hardware in the storage
pouch as it could present a danger to a child if retrieved and could also damage the mattress.

15
Toddler Bed Conversion Kit item STK-3435 is
available as an option to convert the Stationary Side
Crib to a toddler bed. Contact your youngAmerica
dealer to purchase this item.
Accessories and Options

16
Stanley
PO Box 30
Stanleytown, VA 24168
For parts, contact your Stanley Furniture dealer.
For additional consumer information call our Customer Service Department at:
1-(276)-627-2100 Mon.-Fri., 8am-5pm Eastern Standard Time
Furniture
12122011

17
Número de modelo:
SSC 1400
Su pequeño dormirá a salvo en esta cuna de youngAmerica. Un ensamblaje adecuado
le asegurará que se han tomado todas las precauciones para diseñar esta cuna pensando
en la seguridad de su bebé. Está certificada y cumple con todas las pautas de seguridad
establecidas por ASTM International y por la Comisión de Seguridad de Productos para
el Consumidor (Consumer Product Safety Commission, CPSC).
Gracias por comprar una cuna de youngAmerica. Si encuentra que le falta alguna
pieza o le parece que una pieza presenta alguna clase de defecto, comuníquese con
su vendedor minorista de youngAmerica para solicitar ayuda.
Instrucciones para ensamblar la cuna Built to Grow
IMPORTANTE: CONSERVE ESTAS INSTRUCCIONES PARA
REFERENCIAS FUTURAS. LÉALAS CUIDADOSAMENTE.

18
!ADVERTENCIA: EL INCUMPLIMIENTO DE LAS ADVERTENCIAS
E INSTRUCCIONES DE ENSAMBLAJE PUEDE PROVOCAR LESIONES GRAVES O LA MUERTE.
 Cuando el niño ya puede ponerse de pie, baje el colchón a la posición más baja
y retire los protectores, los juguetes grandes y otros objetos que pudieran servir
como escalones para que el niño trepe.
 Cuando el niño pueda treparse o alcance una altura de 90 cm (35 pulg.), la cuna
no se deberá utilizar más.
 NO coloque la cuna cerca de ventanas donde las cuerdas de persianas o cortinas
puedan estrangular al niño.
 Los pediatras recomiendan que los bebés sanos se coloquen de espaldas para
dormir con el fin de reducir el riesgo de síndrome de muerte súbita del lactante,
a menos que su médico le indique lo contrario.
 Para ayudar a prevenir la estrangulación ajuste todos los sujetadores. Un sujetador
flojo puede enganchar una parte del cuerpo o de la ropa del bebé.
 ¡Las cuerdas pueden provocar estrangulación! No coloque objetos con cuerdas
alrededor del cuello del niño, como los cordones de las capuchas o las cintas del
chupete. No deje cuerdas colgando sobre la cuna ni se las ponga a los juguetes.
 Antes de ensamblar o utilizar la cuna, verifique que no tenga piezas dañadas,
flojas, faltantes o con bordes filosos. NO utilice la cuna si le faltan piezas o están
rotas. Comuníquese con su representante o escriba a Young America, PO Box 30,
Stanleytown, VA 24168, para solicitar piezas de reemplazo e instrucciones de
instalación, según sea necesario.
 NO sustituya las piezas. Utilice solamente los pernos o las piezas provistas por
el fabricante o piezas de calidad similar e iguales dimensiones. No deje expuestos
los extremos de los pernos ni los bordes filosos.
 Respete las advertencias para todos los productos de la cuna.
 Si desea volver a pintar la cuna, utilice pintura no tóxica específica para
productos infantiles.
 Los bebés pueden asfixiarse con las ropas de cama mullidas. Nunca agregue
una almohada, un edredón ni almohadillas de protección.
 Los niños pueden asfixiarse en los espacios entre los laterales de la cuna
y un colchón muy pequeño.
 Nunca utilice bolsas plásticas ni otras películas plásticas para cubrir el colchón
porque pueden provocar asfixia.
 No permita que el niño gatee ni juegue debajo de la cuna.
 Tenga cuidado al usar vaporizadores. Dirija el chorro de vapor lejos de la cuna
y de cualquier otro mueble de madera.
 Debe ensamblar toda la cuna antes de utilizarla.
 Lea todas las instrucciones antes de ensamblar la cuna. CONSERVE LAS
INSTRUCCIONES PARA USOS FUTUROS.

19
Las ilustraciones de la cuna de estas instrucciones son genéricas. Es posible que la cuna que
haya comprado no se parezca a las de las ilustraciones; sin embargo, todas las cunas se en-
samblan de la misma manera.
Identificación de las piezas
2 extremos de la cuna
Plataforma del colchón
2 barandas de base
2 laterales de la cuna
 PRECAUCIÓN: El colchón que se utilice en esta cuna debe m
edir 27−1/4" × 51−5/8" como mínimo con un espesor entre 4" y 6".
Cuando se convierte auna cama del niño:
 NUNCA usela cama conniños menores de 15meses de edad.
 El peso máximode sus destinatariosno deberá ser mayorde 50libras (22.7kg).

20
4 pernos de conexión
de 2 3/8" (1/4" × 20 vueltas
por pulgada lineal)
16 pernos de conexión
de 2” (1/4 × 20 vueltas
por pulgada lineal)
2 llaves Allen
Identificación de las piezas de tornillería
Utilice las siguientes ilustraciones para identificar las piezas de tornillería incluidas.
6 pasadores posicionadores
4 soportes del colchón
con pernos