Zanussi ZDTS300 User manual

User manual
Dishwasher
ZDTS 300

Thank you for selecting our
appliance
We wish you lots of enjoyment with your new
appliance and we hope that you will consider
our brand again when purchasing household
appliances.
Please read this user manual carefully and
keep it throughout the product life cycle as a
reference document. The user manual should
be passed on to any future owner of the
appliance.
Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Control panel _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4
Audible signals _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5
Select and start a washing
programme _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Washing programmes _ _ _ _ _ _ _ _ _ _ _ 8
First use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Set the water softener _ _ _ _ _ _ _ _ _ _ _ 9
Use of dishwasher salt _ _ _ _ _ _ _ _ _ _ 11
Use of rinse aid_ _ _ _ _ _ _ _ _ _ _ _ _ _ 12
Loading cutlery and dishes_ _ _ _ _ _ _ _ 13
Use of detergent _ _ _ _ _ _ _ _ _ _ _ _ _ 16
Unloading the dishwasher _ _ _ _ _ _ _ _ 17
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ 17
Environment concerns _ _ _ _ _ _ _ _ _ _ 19
What to do if ... _ _ _ _ _ _ _ _ _ _ _ _ _ _ 20
Technical data _ _ _ _ _ _ _ _ _ _ _ _ _ _ 22
Consumption values _ _ _ _ _ _ _ _ _ _ _ 22
Hints for test institutes _ _ _ _ _ _ _ _ _ _ 22
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 23
2

Safety information
In the interest of your safety and to ensure the
correctuse,beforeinstallingandfirstusingthe
appliance, read this user manual carefully, in-
cluding its hints and warnings. To avoid
unnecessary mistakes and accidents, it is im-
portant to ensure that all people using the
appliancearethoroughlyfamiliarwithitsopera-
tion and safety features. Save these instruc-
tions and make sure that they remain with the
applianceifitismovedorsold,sothateveryone
usingitthroughitslifewillbeproperlyinformed
on appliance use and safety.
Correct use
• Thisdishwasherisonlyintendedforwashing
household utensils suitable for machine
washing.
• Do not put any solvents in the dishwasher.
This could cause an explosion.
• Knives and other items with sharp points
must be loaded in the cutlery basket with
their points down or placed in a horizontal
position in the upper basket.
• Onlyuseproducts (detergent,salt andrinse
aid) suitable for dishwashers.
• Avoid opening the door whilstthe appliance
is in operation, hot steam may escape.
• Donottakeanydishesoutofthedishwasher
before the end of the dishwashing cycle.
• After use, isolate the appliance from the
power supply and turn off the water supply.
• This product should be serviced only by an
authorisedserviceengineer,andonlygenu-
ine spare parts should be used.
• Undernocircumstancesshouldyouattempt
to repair the machine yourself. Repairs car-
riedoutbyinexperiencedpersonswillcause
injury or serious malfunctioning. Contact
your local Service Force Centre. Always in-
sist on genuine spare parts.
General safety
• Dishwasherdetergentscan causechemical
burns to eyes, mouth and throat. Could en-
danger life! Comply with the safety instruc-
tions of the dishwasher detergent
manufacturer.
• Thewaterinyourdishwasherisnotfordrink-
ing. Detergent residues may still be present
in your machine.
• Ensure that the door of the dishwasher is
alwaysclosedwhenitisnotbeingloadedor
unloaded.Inthiswayyouwillavoidanybody
tripping over the open door and hurting
themselves.
• Do not sit or stand on the open door.
Child safety
• This appliance is designed to be operated
by adults. Don’t allow children to use the
dishwasher unsupervised.
• Keepallpackagingwellawayfromchildren.
There is risk of suffocation.
• Keep all detergents in a safe place out of
children’s reach.
• Keep children well away from the
dishwasher when the door is open.
3

Installation
• Check your dishwasher for any transport
damage. Never connect a damaged ma-
chine. If your dishwasher is damaged con-
tact your supplier.
• All packaging must be removed beforeuse.
• Anyelectricalandplumbingworkrequiredto
install this appliance must be carried out by
a qualified and competent person.
• For safety reasons it is dangerous to alter
the specifications or attempt to modify this
product in any way.
• Never use the dishwasher if the electrical
supplycableandwaterhosesaredamaged;
orifthecontrolpanel,worktoporplintharea
are damaged such that the inside of the ap-
pliance is freely accessible. Contact your
local Service Force centre, in order to avoid
hazard.
• All sides of the dishwashermust never be
drilled to prevent damage to hydraulic and
electric components.
CAUTION!
For electrical and water connection carefully
follow the instructions given in specific para-
graphs.
Control panel
4

1On/Off button
2Programme selection buttons
3Delay start button
4Indicator lights
5Function buttons
Functions buttons
In addition to the dishwashing programme se-
lection, the following functions can also be set
with the help of these buttons:
• the setting of the water softener,
• deactivation/activation of the audible sig-
nals.
Setting mode
IMPORTANT!
Always remember that when:
– setting the water softener,
– deactivation/activation of the audible sig-
nals,
the appliance MUST be in setting mode:
• PressOn/Offbutton,Allprogrammelightare
illuminated = the appliance is in setting
mode.
• Press On/Off button, ONLY a programme
button is illuminated = last performed or se-
lected programme still set.
In this case, to return to setting mode, the
programme has to be cancelled.
Tocancelasetprogrammeoraprogramme
in progress
Simultaneously press function buttons Band
C, until ALL programme button lights are illu-
minated. The programme has been cancelled
and the machine is now in setting mode.
Indicator lights
Salt Illuminates when the special salt has run out.
Is never illuminated while a washing programme is
running.
Rinse aid Illuminates when the rinse aid has run out.
Is never illuminated while a washing programme is
running.
End of programme Illuminateswhen thewashingprogrammehasended.
It also has added functions of visual signalling as:
– the setting of the water softener,
– deactivation/activation of the audible signals,
– intervention of an alarm due to the malfunction of
the machine.
5

Audible signals
Audible signals have been introduced to help
indicate which operations the dishwasher is
performing:
• setting the water softener,
• end of the programme,
• intervention of an alarm due to malfunction.
IMPORTANT!
Factory setting: audible signals activated.
Deactivation/activation of the audible sig-
nals
1. PressOn/Offbutton.Thedishwashermust
be in setting mode.
2. Simultaneously press and hold function
buttons Band Cuntil the lights of function
buttons A, Band Cstart flashing.
3. Press function button C, the lights of func-
tionbuttonsAand Bturn offwhile thelight
of function button Cgoes on flashing. At
the same time the end of programme in-
dicator light illuminates indicating that the
audible signals are active.
4. To deactivate the audible signals press
again function button C, the end of pro-
gramme indicatorlightturns off,indicating
that the audible signals have been deacti-
vated.
5. To memorise the operation switch off the
dishwasherbypressingtheOn/Off button.
To activate again the audible signals simply
follow the above operations until the end of
programme indicator light illuminates.
Select and start a washing programme
IMPORTANT!
Selectthewashingprogrammeanddelaystart
with the door slightly opened. The start of the
programmeorthecountdownofthedelaystart
willoccuronlyaftertheclosureofthedoor.Until
then it is possible to modify the set made.
1. Check that the baskets have been loaded
correctly and that the spray arms are free
to rotate
2. Check that the water tap is opened
3. Press the On/Off button. The dishwasher
must be in setting mode.
6

4. Press the button corresponding to the re-
quired programme (see "Washing pro-
grammes" chart).
Whenaprogrammehasbeenselectedthe
corresponding light will illuminate.
5. Close the dishwasher door, the pro-
gramme starts automatically.
Setting and starting the
programme with "delay start"
1. After having selected the washing pro-
gramme, press the delay start button until
thelightcorrespondingtothechosenhours
flashes (3h, 6h, 9h).
2. Closethedishwasherdoor,thecountdown
starts automatically.
3. The countdownwilldecreasewithstepsof
3 hours.
4. The opening of the door will interrupt the
countdown.Closethedoor;thecountdown
will continue from the point at which it was
interrupted.
5. Once the delay start has elapsed the pro-
gramme will start automatically.
Cancelling the delay start
Tocancel adelay startinprogressyouhave to
reset the dishwasher.
Press simultaneously and keep pressed func-
tionbuttonsBandC untilallprogrammebutton
light are illuminated.
Cancelling a delay start involves also the can-
celling of the washing programme set. In this
case you have to set the washing programme
again.
CAUTION!
Interrupt or cancel a washing programme in
progress ONLY if it’s absolutely necessary.
Attention! Hot steam may escape when the
door is opened. Open the door carefully.
Interrupt a washing programme in pro-
gress:
• Open the dishwasher door; the programme
willstop.Closethedoor;theprogrammewill
start from the point at which it was interrup-
ted.
Cancel a washing programme in progress
• Open the dishwasher door; press
simultaneously and keep pressed function
buttons Band C until all programme button
is illuminated. The washing programme has
been cancelled. .
• If a new washing programme is to be selec-
ted, check that there is detergent in the
detergent dispenser.
Cancelling the "delay start"
• Tocanceladelaystartinprogress,openthe
door and press the delay start button, the
corresponding light turns off.
• close the door, the set washing programme
will start automatically.
End of the washing programme
• The dishwasher will automatically stop and
an audible signal informs you of the end of
the washing programme.
• Open the dishwasher door.
•The end of programme indicator light is il-
luminated.
• The indicator light of the programme just
ended will remain on.
• Switch off the dishwasher by pressing the
On/Off button.
7

IMPORTANT!
When the washing programme has finished, it
is recommended that the dishwasher is un-
plugged and the water tap turned off.
Washing programmes
Programme Degree of soil Type of load Programmedescription
Intensive 70° Heavy soil Crockery, cutlery, pots
and pans Prewash Main wash
2 intermediate rinses
Final rinse
Drying
Normal 65° Normal soil Crockery, cutlery, pots
and pans Prewash Main wash
1 intermediate rinse
Final rinse
Drying
Quick 65° A 30'
1)
Light soil Crockery and cutlery Main wash
Final rinse
Bio 50°
2)
Normal soil Crockery and cutlery Prewash
Main wash
1 intermediate rinse
Final rinse
Drying
Rinse and Hold Any.
Partial load (to be completed later in the day). 1coldrinse(toavoidfood scraps from sticking
together).
Thisprogrammedoesnot
require the use of deter-
gent.
1) Ideal for washing a partially loaded dishwasher. This is perfect daily programme, made to meet the needs of a family of 4
persons who only wish to load breakfast and dinnercrockery and cutlery.
2) Test programme for test institutes.
8

First use
Beforeusingyourdishwasher forthe firsttime:
• Ensurethattheelectricalandwaterconnec-
tionscomplywiththeinstallationinstructions
• Removeallpackagingfrominsidethe appli-
ance
• Set the water softener
• Pour1litreofwater insidethe saltcontainer
and then fill with dishwasher salt
• Fill the rinse aid dispenser
When using tablets that integrate rinse aid
and detergent:
there is no need to fill up with rinse aid
– set the water softener
– add special (dishwasher) salt
When using tablets that integrate rinse aid,
detergent,saltfunctionandotheradditives:
there is no need to fill up with special salt or
rinse aid.
Check whether these detergents are suitable
for your water hardness. Follow the manufac-
turers instructions.
– Set the water hardness to level 1.
IMPORTANT!
Ifthedryingresultsarenotsatisfactorywerec-
ommend that you:
1. Filluptherinseaiddispenserwithrinseaid.
2. Set the rinse aid dosage to position 2.
If you decide in future to use separated deter-
gents, we advise that you:
– Fill up the salt and rinse aid container.
– Adjust the water hardness setting to the
highestleveland perform 1normalwashing
programme without loading any dishes.
– Adjustthewaterhardnesssettingaccording
to the hardness of the water in your area.
– Adjust the rinse aid dosage
Set the water softener
The dishwasher is equipped with a water
softenerdesignedtoremovemineralsandsalts
fromthewatersupply,whichwouldhaveadet-
rimental or adverse effect on the operation of
the appliance.
The higher the content of these minerals and
salts,theharderyourwateris.Waterhardness
is measured in equivalent scales, German de-
grees (°dH), French degrees (°TH) and mmol/
l (millimol per litre - international unit for the
hardness of water).
The softener should be adjusted according to
the hardness of the water in your area. Your
local Water Authority can advise you on the
hardness of the water in your area.
9

Water hardness Adjusting the water hardness
setting Use of salt
°dH °TH mmol/l manually electronically
51 - 70 91 - 125 9,1 - 12,5 2level 10 yes
43 - 50 76 - 90 7,6 - 8,9 2level 9 yes
37 - 42 65 - 75 6,5 - 7,5 2level 8 yes
29 - 36 51 - 64 5,1 - 6,4 2level 7 yes
23 - 28 40 - 50 4,0 - 5,0 2level 6 yes
19 - 22 33 - 39 3,3 - 3,9 2level 5 yes
15 - 18 26 - 32 2,6 - 3,2 1level 4 yes
11 - 14 19 - 25 1,9 - 2,5 1level 3 yes
4 - 10 7 - 18 0,7 - 1,8 1level 2 yes
< 4 < 7 < 0,7 1level 1 no
The water softener must be set in both ways:
manually, using the water hardness dial and
electronically.
Setting the water softener manually (see table)
Set switch to position 1 or
2
The water softener is factory set at position 2.
Setting the water softener
electronically (see table)
The dishwasher is factory set at level 5.
10

1. Press the On/Off button. The dishwasher
must be in setting mode.
2. Simultaneously press and hold function
buttonsB andC untilthelightsofthefunc-
tion buttons A, Band C start flashing.
3. Pressfunctionbutton A, thelightsfunction
buttons B and C turn off while the light of
function button Agoes flashing, at the
same time the end of programme indica-
tor light starts to flash, along with a se-
quenceofintermittentaudiblesignals.The
current level is indicated by the number of
flashesoftheendofprogrammeindicator
lightwithasequenceofintermittentaudible
signals and a pause of a few seconds.
Examples:
5 flashes / 5 intermittent audible signals,
pause,
5 flashes / 5 intermittent audible signals,
pause, etc...= level 5
6 flashes / 6 intermittent audible signals,
pause,
6 flashes / 6 intermittent audible signals,
pause, etc...= level 6
4. Tochangethelevelpressthefunctionbut-
tonA.Eachtimebuttonispressedthelevel
changes (For the selection of a new level
see the chart).
Examples:
Ifthecurrentlevelis5,bypressingfunction
button Aonce, level 6 is selected. If the
current level is 10, by pressing button A
once, level 1 is selected.
5. To memorise the operation, switch off the
dishwasherbypressingtheOn/Off button.
Use of dishwasher salt
CAUTION!
Use only special salt suitable for dishwashers.
11

Unscrew the cap. Only before filling with
salt for the first time, fill
thesaltcontainerwithwa-
ter.
Usingthefunnelprovided,
pour in the salt until the
containerisfilledwithsalt.
Remove any trace of salt. Replace the cap tightly
turningit clockwise until it
stops with a click.
IMPORTANT!
Immediately start a complete programme.
IMPORTANT!
Waterwilloverflowfromthecontainerassaltisadded.
IMPORTANT!
Top up the special salt when the light on the
control panel illuminates.
12

Use of rinse aid
Open the lid. Fill up with rinse aid. The
maximumlevelforfillingis
indicated by "max"
Clean up any rinse aid
which overflows. Close
the lid and press until it
locks.
CAUTION!
Never fill the rinse aid dispenser with any other sub-
stances (e.g. dishwasher cleaning agent, liquid deter-
gent). This would damage the appliance.
IMPORTANT!
Topuptherinseaidwhenthelightonthecontrolpanel
illuminates.
Adjusting the dosage of rinse aid
Increase the dose if there are drops of water or lime
spots on the dishes after washing. Reduce the dose if there are whitish streaks on the dishes or a bluish film on glassware or knife blades.
Open the lid. Setthedosagelevel.(The
dose is factory set in po-
sition 4).
Closethelidandpressun-
til it locks.
Loading cutlery and dishes
Sponges,householdclothsandanyobjectthat
can absorb water may not be washed in the
dishwasher.
13

• Before loading the dishes, you should:
– Remove all left over food and debris.
– Soften remnants of burnt food in pans
• Whenloadingthedishesandcutlery,please
note:
– Dishes and cutlery must not impede the
rotation of the spray arms.
– Loadhollowitemssuchascups,glasses,
pans,etc.withtheopeningdownwardsso
that water cannot collect in the container
or a deep base.
– Dishes and items of cutlery must not lie
inside one another, or cover each other.
– To avoid damage to glasses, they must
not touch.
– Lay small objects in the cutlery basket.
• Plastic items and pans with non stick coat-
ings have a tendency to retain water drops;
these items will not dry as well as porcelain
and steel items.
• Light items (plastic bowls etc.) must be loa-
ded in the upper basket and arranged so
they do not move.
For washing in the dishwasher the following cutlery and dishes
are not suitable: are of limited suitability:
• Cutlery with wooden, horn, china or mother-of-
pearls handles.
• Plastic items that are not heat resistant.
• Oldercutlery with gluedpartsthat are nottempera-
ture resistant.
• Bonded cutlery items or dishes.
• Pewter or copper items.
• Lead crystal glass.
• Steel items prone to rusting.
• Wooden platters.
• Items made from synthetics fibres.
• Only wash stoneware in the dishwasher if it is
specially marked as being dishwasher-safe by the
manufacturer.
• Glazed patterns may fade if machine washed
frequently.
• Silver and aluminium parts have a tendency to dis-
colour during washing: Residues, e.g. egg white,
eggyolkandmustardoftencausediscolouringand
stainingonsilver.Thereforealwayscleanleft-overs
from silver immediately, if it is not to be washed
straight after use.
14

Load cutlery. For best re-
sults we recommend you
tousethecutlerygridpro-
vided (if the size and di-
mensions of the cutlery
allow it)
Place knives and other
itemsofcutlerywithsharp
points or edges with their
handles facing upwards.
Risk of injury!
Loadthelowerbasket.Ar-
range serving dishes and
largelidsaroundtheedge
of the basket.
Load upper basket. Light
items (plastic bowls etc.)
must be loaded in the up-
per basket and arranged
so they do not move.
For taller items, the cup
racks can be folded up-
wards.
Adjusting the height of the
upper basket
Ifwashingverylargeplates you can load them
inthelowerbasketaftermovingtheupperbas-
ket to the higher position.
Maximum height of the dishes in :
upper basket lower basket
With upper basket raised 20 cm 31 cm
With upper basket lowered 24 cm 27 cm
15

Tomovetothehigherpositionproceedasfollows:
1. Pull out the basket until it stops.
2. Carefully lift both sides upwards until the mecha-
nism is engaged and the basket is stable.
Tolowerthebaskettotheoriginalpositionproceed
as follows:
1. Pull out the basket until it stops.
2. Carefullyliftbothsidesupwardsandthenallowthe
mechanism to drop back down slowly, keeping
hold of it.
IMPORTANT!
Never lift or lower the basket on one side only IMPORTANT! When the basket is in the higher position you
will not be able to use the cup racks.
Use of detergent
IMPORTANT!
Only use detergents suitable for dishwashers. Observe the manufacturer’s dosing and stor-
age recommendations.
Open the lid. Fill in the detergent in
compartment A.Observe the dosing lev-
els.
16

Forprogrammeswithpre-
wash add an additional
detergent dose in com-
partmentB.
When using detergent
tablets: place detergent
tabletsincompartmentA.
Close the lid.
Detergent tablets
Detergent tablets from different manufacturers
dissolve at different rates. For this reason,
some detergent tablets do not attain their full
cleaning power during short washing pro-
grammes.Therefore,pleaseuselongwashing
programmes when using detergent tablets, to
ensure the complete removal of detergent
residuals.
Unloading the dishwasher
• Hot dishes are sensitive to knocks.
The dishes should therefore be allowed to
cool down before removing from the appli-
ance.
• Empty the lower basket first and then the
upperone;thiswillavoidwaterdrippingfrom
theupperbasketontothedishesinthelower
one.
• Watermayappearonthesidesandthedoor
of the dishwasher as the stainless steel will
eventually become cooler than the dishes.
CAUTION!
When the washing programme has finished, it
is recommended that the dishwasher is un-
plugged and the water tap turned off.
Care and cleaning
Cleaning the filters
IMPORTANT!
NEVER use the dishwasher without filters. In-
correctrepositioningandfittingofthefilterswill
produce poor washing results.
17

Clean filters A, Band C
thoroughly under running
water.
Turn the handle about 1/4
turn anticlockwise and re-
move filters Band C.
Remove filter Afrom the
baseofthewashingcom-
partment.
Replace the filters and
lock by turning thehandle
clockwise to the stop.
Cleaning the spray arms
NEVER try to remove the spray arms.
Ifresiduesofsoilhavecloggedtheholesinthe
spray arms, remove them with a cocktailstick.
External cleaning
Cleantheexternalsurfacesofthemachineand
control panel with a damp soft cloth. If
necessary use only neutral detergents. Never
use abrasive products, scouring pads or sol-
vent (acetone, trichloroethylene etc....).
Internal cleaning
Ensure that the seals around the door, the de-
tergent and rinse aid dispensers are cleaned
regularly with a damp cloth.
Werecommendevery3monthstorunthewash
programme for heavy soiled dishes using de-
tergent but without dishes.
Prolonged periods of non-
operation
If you are not using the machine for any pro-
longed period of time you are advised to:
1. Unplug the appliance and then turn off the
water.
18

2. Leave the door ajar to prevent the forma-
tion of any unpleasant smells.
3. Leave the inside of the machine clean.
Frost precautions
Avoid placing the machine in a location where
the temperature is below 0°C. If this is
unavoidable,emptythemachine,closetheap-
pliance door, disconnect the water inlet pipe
and empty it.
Moving the machine
Ifyouhavetomovethemachine(movinghouse
etc....):
1. Unplug it.
2. Turn the water tap off.
3. Remove the water inlet and discharge ho-
ses.
4. Pull the machine out together with the ho-
ses.
Avoid over tilting the machine during transpor-
tation.
Environment concerns
The symbol on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. Byensuringthisproduct
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic com-
ponents are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at the
community waste disposal facilities.
CAUTION!
When a unit is no longer being used:
• Pull the plug out of the socket.
• Cut off the cable and plug and dispose of
them.
• Dispose of the door catch. This prevents
children from trapping themselves inside
and endangering their lives.
19

What to do if ...
The dishwasher will not start or stops during
operation.
Certain problems are due to the lack of simple
maintenance or oversights, which can be
solvedwiththehelpoftheindicationsdescribed
in the chart, without calling out an engineer.
Switchoffthedishwasherandcarryoutthefol-
lowing suggested corrective actions.
Fault code and malfunction Possible cause and solution
•1 intermittent audible signal
•continuous flashing of the light of the running
programme
•1flashofthe"endofprogramme"indicatorlight
The dishwasher does not fill with water.
• The water tap is blocked or furred with limescale.
Clean the water tap.
• The water tap is turned off.
Turn the water tap on.
• Thefilter(wherepresent)inthethreadedhosefitting
at the water inlet valve is blocked.
Clean the filter in the threaded hose fitting.
• The water inlet hose has not been correctly laid or
it is bent or squashed.
Check the water inlet hose connection.
•2 intermittent audible signals
•continuous flashing of the light of the running
programme
•2 flashes of the "end of programme " indicator
light
The dishwasher will not drain.
• The sink spigot is blocked.
Clean outthe sink spigot.
• The water drain hose has not been correctly laid or
it is bent or squashed.
Check the water drain hose connection.
•3 intermittent audible signals
•continuous flashing of the light of the running
programme
•3 flashes of the "end of programme" indicator
light
Anti-flood device is activated
Close the water tap and contact your local Service
Force Centre.
The programme does not start. • Thedishwasherdoorhasnotbeenproperlyclosed.
Close the door.
• The main plug is not plugged in.
Insert the mains plug.
• The fuse has blown in the household fuse box.
Replace the fuse.
20