zBoost SOHO YX560P User manual

zBoost® SOHO YX560P
User Guide
zBoost products have a 30-day money back guarantee when purchased directly from
Wi-Ex®. If product is purchased from a reseller or third party, the purchaser is subject to the
policies of the third party.
2 Year Manufacturer Warranty. Register at www.Wi-Ex.com
v.072312

zBOOST® SOHO YX560P USER GUIDE
i
About zBoost® from Wi-Ex®
Wi-Ex, the leader in cell phone signal boosters manufactures zBoost, the award-winning line
of cell phone signal boosters that enhance the performance of your cell phone, smartphone
and wireless data card.
Patented technologies protect the carrier network.
zBoost products have more awards, more sales and more locations than all other signal
boosters…COMBINED.
FCC Information
FCC ID: SO4YX545-PCS-CEL2
Warning: Changes or modications to this device not expressly approved by Wi-Ex® could void the
user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If the equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. In accordance with FCC requirements of human exposure to radiofrequency
elds, the radiating element (antenna) shall be installed such that a minimum separation distance of
20cm (8in) is maintained from all persons.
Industry Canada Regulations
IC ID: 5544A-YX545PCSCL2
This Class B digital apparatus meets all requirements of the Canadian Interference Causing
Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
The term “IC:” before the radio certication number only signies that Industry Canada technical
specications were met.
RF Exposure: The manufacturer’s rated output power of this equipment is for single carrier
operation. For situations when multiple carrier signals are present, the rating would have to be
reduced by 3.5 dB, especially where the output is re-radiated and can cause interference to
adjacent band users. This power reduction is to be by means of input power or gain reduction and
not by an attenuator at the output of the device.

zBOOST® SOHO YX560P USER GUIDE
ii
zBOOST® SOHO YX560P USER GUIDE
iii
Package Contents: zBoost SOHO YX560P
⑦
③
④
⑤
⑥
Before you begin, make sure all of the following parts came with your zBoost SOHO YX560P
Literature Contents:
① Set-up overview for zBoost SOHO YX560P
(User Guide online only)
Product Contents:
② zBoost Base Unit
③ Base Unit Antenna
④ Power Supply
⑤ RG-6 Coax Cable, 50 feet
⑥ Signal Antenna
⑦ Signal Antenna Mounting Hardware
Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence
canadienne causant des règlements d’équipement. L’opération est sujette aux deux conditions
suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter
n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.
Le fabricant nominale de la puissance de sortie de ce matériel est simple transporteur. Pour les
situations lorsque plusieurs signauxporteurs sont présents, l’évaluation devrait être réduite de
3.5 dB, en particulier lorsque le signal de sortie est ré-émise et peut provoquer des interférences
adjacentes à la bande utilisateurs. Ce pouvoir est de la réduction par le biais de la sortie
d’alimentation ou la réduction de gain et non par un atténuateur à la sortie du dispositif.
Please note: This unit has been approved for use in Canada under RSS 131, however, consent
for the use of this device to improve cellular or PCS coverage, must be obtained through your
cellular or PCS provider, prior to placing the unit in operation. Please refer to the Industry Canada
document CPC 2-1-05, Section 6.1 available or viewable at:
http://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html
Copyright Notice
This manual is copyrighted. All rights reserved. This manual, whole or in part, may not be copied,
photocopied, reproduced, translated or reduced to any electronic medium or machine readable
form for distribution. This manual whole or in part, may not be modied without prior consent, in
writing, from Wireless Extenders.
Copyright © 2012 by Wireless Extenders, Inc.
Trademarks
Wireless Extenders, Wi-Ex, the Wi-Ex logo, zBoost, the zBoost logo and Extending Cell Zones are
registered trademarks of Wireless Extenders, Inc.
Safety Guidelines
In accordance with FCC requirements of human exposure to radiofrequency elds, the radiating
element (antenna) shall be positioned such that a minimum separation distance of 8 inches (20cm)
is maintained between the radiating element and the user and/or general population.
Limited Liability
In no event shall Wireless Extenders be liable for any direct, indirect, special, punitive, incidental,
exemplary or consequential damages, or any damages, whether in an action under contract,
negligence, or any other theory, arising out of or in connection with the set up of, use of, inability
to use, or performance of the information, services, products, and materials available from this
manual. These limitations shall apply notwithstanding any failure of essential purpose of any
limited remedy. Because some jurisdictions do not allow limitations on how long an implied
warranty last, or the exclusion or limitation of liability for consequential or incidental damages, the
above limitations may not apply to you.
For full warranty guidelines, see page 13
Safety and Product Warranty Information ②
Note
Changes or modications not expressly approved by
Wi-Ex® could void the user’s authority to operate this
equipment and/or void the product warranty.
SETUP OVERVIEW
①

zBOOST® SOHO YX560P USER GUIDE
iv
zBOOST® SOHO YX560P USER GUIDE
1
Optional zBoost Accessories Table of Contents
FCC Information ............................................................................................................................i
Industry Canada Regulations ........................................................................................................i
Safety and Product Warranty Information .................................................................................... ii
Copyright Notice ..........................................................................................................................ii
Trademarks ..................................................................................................................................ii
Safety Guidelines .........................................................................................................................ii
Limited Liability ............................................................................................................................ii
Package Contents: zBoost SOHO YX560P ................................................................................. iii
Optional zBoost Accessories ...................................................................................................... iv
Table of Contents .......................................................................................................................... 1
Overview ........................................................................................................................................ 2
Why Indoor Signals Can Be Weak ............................................................................................... 2
Preparing to Set Up Your zBoost Product .................................................................................... 3
Check for Signal Strength ........................................................................................................... 3
Tools Needed .............................................................................................................................. 3
Important: Before installing, please note these important factors in determining performance ..... 4
Determine the Needed Coverage Area ........................................................................................ 4
Additional Cable Requirements ................................................................................................... 5
Grounding the Signal Antenna ..................................................................................................... 5
Securing Cable with a Drip Loop ................................................................................................. 5
Power Requirements ................................................................................................................... 5
Setting Up Your zBoost Signal Booster ....................................................................................... 6
FIRST: Mount the Signal Antenna ................................................................................................ 6
SECOND: Position the Base Unit ................................................................................................ 6
THIRD: Run the coaxial cable between the Base Unit and Signal Antenna .................................. 7
FOURTH: Connect the zBoost Base Unit to the power supply and plug into an outlet ................. 7
FIFTH: Antenna Aiming ............................................................................................................... 8
Conrm That Your zBoost is Working Properly ............................................................................ 8
Improving Your Coverage Area ..................................................................................................... 9
zBoost Base Unit Light Indicators .............................................................................................. 10
Technical Specications ..............................................................................................................11
Frequently Asked Questions ...................................................................................................... 12
Warranty Information .................................................................................................................. 13
The following accessories are available to improve signal reception and provide increased coverage
in your home or ofce. Please see our website for complete selection.
To order, call 1-800-871-1612 or visit, www.Wi-Ex.com
Part # Description
Most Popular Accessories
YX039-PCS-CEL Bi-Directional receiving Signal Antenna upgrade
(13 dBi PCS / 8 dBi CEL)
YX027-PCS-CEL Directional transmitting Base Unit Antenna upgrade
(9 dBi PCS / 6 dBi CEL)
Other Accessories:
YX012 Outside Grounding Kit
YX030-15W 15 ft coax extension cable, RG-6
YX030-35W 35 ft coax extension cable, RG-6
YX031-100W 100 ft coax extension cable, RG-11
YX030-08W 8 inch at window entry cable
YX050-PCS-CEL Omni-Directional transmitting ceiling-mount Base Unit Antenna
(2 dBi PCS / 1 dBi CEL)
CANT-0041
YX026-CEL Directional receiving Signal Antenna upgrade (11 dBi)
YX023-PCS Directional receiving Signal Antenna upgrade (13 dBi)
YX015D PCS-CEL Antenna Combiner

zBOOST® SOHO YX560P USER GUIDE
2
zBOOST® SOHO YX560P USER GUIDE
3
Preparing to Set Up Your zBoost Product
Thank you for choosing zBoost. You will now be able to use your cell phone INSIDE your home or
ofce. Gone are the days when you had to go to the window upstairs or walk outside to use your
cell phone. Like a skylight that brings sunlight into your home, zBoost transports and amplies the
outdoor cellular signals into your home or ofce.
By following the easy instructions in this user guide, you will be Extending Cell Zones™ into your
home or ofce.
Why Indoor Signals Can Be Weak
There are several obstacles that can contribute to the poor reception you receive in your home or
ofce:
1. Location of the Cell Phone Tower in Relation to Your Home/Ofce
While cell phone providers have tried to place cell phone towers to provide the best overall
coverage, local ordinances and terrain features can impose restrictions on where these
towers can be placed, thus, limiting the signal strength available at your location.
2. Obstructions Caused by Buildings, Terrain and Trees
Cell phone signals can be completely blocked or reected by buildings, walls, trees, hills
and other terrain features resulting in low signal strength.
3. Energy Efcient Windows
These new windows can also affect signal penetration into the house.
Check for Signal Strength
Before placing a zBoost in your home, make sure that you can place calls on the outside of your
home, in the attic, at roof level or wherever you plan to place the Signal Antenna. zBoost can only
bring signal into your home when signal reaches the Signal Antenna. If there is no signal, zBoost
will not work for you.
Using your cell phone, place a call from an outdoor location to conrm that enough signal is present
to complete the call. If a weak signal is available at ground level, check the signal strength in your
attic or at roof level location where the signal will likely be stronger and where the Signal Antenna
can be placed for best performance.
If you can reliably make and receive calls outside your home, then zBoost can bring the signal into
your home.
If only one signal bar is displayed on your cell phone outside, indoor coverage will be
limited to one small room. We recommend placing the Signal Antenna outside and/or purchasing
a Wi-Ex upgrade Signal Antenna for increased coverage (see page iv).
Tools Needed
The following tools are needed to set up zBoost:
• #2 Phillips screwdriver
• Cellular phone operating in the band supported by your zBoost unit
• Drill (may be required for outdoor or attic antenna placement)
Note
Cell phone signal bars are approximate and vary from
phone to phone. The number of bars can uctuate
widely, depending on the location of the phone, the
position or angle of the phone, weather, etc. Most cell
phone signal meters update every 6 to 10 seconds. An
increase of only one bar typically indicates a 4x to 10x
signal increase.
Overview

zBOOST® SOHO YX560P USER GUIDE
4
zBOOST® SOHO YX560P USER GUIDE
5
IMPORTANT: Before Installing, Please Note These Important Factors in
Determining Performance
• Atleast15verticalfeetisneededbetweentheSignalAntenna(receivestheoutsidesignal)
andtheBaseUnitAntenna(rebroadcaststhesignalindoors).Separationlessthan15vertical
feetwillresultindecreasedperformance.Seeillustrationbelow.
• KeeptheSignalAntennaatleast3feetaboveanymetal.
Determine the Needed Coverage Area
Identify the location in your home/ofce where you need signal coverage the most. The zBoost
SOHO YX560P can cover up to 3500 square feet (coverage varies based on outdoor signal level,
building construction, and placement of antennas). Walls, ceilings or oors will reduce the coverage
area.
Additional Cable Requirements
If the distance between the Signal Antenna and the Base Unit exceeds 50 feet, extension cables
are available on our website or at many home improvement and electronic stores. The included
cable is RG-6.
The total cable length should not exceed 65 feet unless upgraded cable and/or upgraded Signal
Antenna (see page iv) is used. A longer cable is helpful only if it allows you to place the Signal
Antenna in a location where you measure stronger signal.
Grounding the Signal Antenna
If the Signal Antenna is placed outdoors, it should be properly grounded. (See page iv for a
recommended grounding kit).
The setup must be in accordance with Article 810 of the National Electric Code (NEC). A listed
antenna discharge unit must be provided for the lead-in coaxial cable per NEC article 8.10.20 or the
shield of the coaxial cable must be permanently and effectively grounded in accordance with NEC
article 8.10.21. Please consult a professional installer or electrician for more information.
Securing Cable with a Drip Loop
If the Signal Antenna is placed outdoors, create a drip loop with
the coaxial cable at the point where the cable enters the building
through an outside wall. This can be done by twisting and
securing the cable into a loop (no less than 4” across) near the
entry point. This will help prevent moisture from gathering at entry
point and leaking into the building. Consult a professional installer
for more information.
Power Requirements
The Base Unit can be plugged into a standard 2 or 3 prong 110 VAC receptacle using the included
power supply. The power supply consumes less than 10W (less than 0.2A). For more information
on power consumption, see “Technical Specications” on page 11.
Warning
The zBoost YX560P base unit MUST only be used with the
provided power adaptor. Use of other power adaptors will
void the warranty and may damage the unit. Use of other
equipment is not FCC approved.
Coax Cable
Exterior Wall
Note
Avoid placing the Signal Antenna near metal such as
wiring, A/C ducts, metal siding, truss plates, etc.
When connecting the cable to the antenna, run the
cable straight down from the antenna. Avoid draping
the coax near the antenna.
15’ of vertical
separation
15’ of vertical
separation
15’ of vertical
separation

zBOOST® SOHO YX560P USER GUIDE
6
zBOOST® SOHO YX560P USER GUIDE
7
Setting Up Your zBoost Signal Booster
provided) to afx to wall - keeping the antenna vertical.
Remember, the zBoost YX560P requires at least 15 feet of vertical separation between the Base
Unit and the Signal Antenna. Generally, increasing this distance (up to 40 feet) will increase the
performance and decreasing the distance will limit zBoost performance.
THIRD: Run the coaxial cable between the Base Unit and Signal Antenna
Use the provided 50 feet of RG-6 coaxial cable to connect the Signal Antenna and the Base Unit.
Run the cable along a descending pipe or through a wall that leads closest to the location of the
Base Unit.
To run the cable from exterior to interior through a window, an 8 inch window-entry cable is
available for purchase (Part: YX030-08W). Should you need additional cable length, 15 foot
extensions (Part: YX030-15W) are available at www.Wi-Ex.com. Please note: the maximum
recommended length for RG-6 is 65. For lengths above 65 feet, upgrade to RG-11. Maximum
recommended length for RG-11 is 120 feet.
NOTE: Refrain from securing cable or drilling holes until the system has been tested.
FOURTH: Connect the zBoost Base Unit to the power supply and plug into an
outlet
Upon initial power up, a solid GREEN LED should appear indicating normal conditions. If a RED
light appears, this may be an indication that the antennas are too close together. Adjustments may
be needed to optimize performance.
FIRST: Mount the Signal Antenna
Choosing the best location for the Signal Antenna provides the best performance and the largest
area of improved signal. Choose a location for the Signal Antenna using your cell phone to
determine the area of strongest signal - typically found outside, above the rooine or in an attic. The
antenna must also remain at least 3 feet above any metal objects such as pipes, metal siding, A/C
unit etc.
Identify the best location for attachment of the mounting bracket – such as an attic cross or main
beam. Secure the mounting bracket at the highest possible point. Position the mounting bracket
and attach the Signal Antenna.
To get the maximum benet, you will want to take special care in pointing the Signal Antenna in the
direction of best signal for your wireless service provider. If you are unsure of the direction of your
provider’s closest network tower, see the Antenna Aiming section on page 8 or you may wish to use
a YX699 RF Signal Meter to help during this process. Once you have determined the optimum
location and angle, secure the antenna.
SECOND: Position the Base Unit
Connect the Base Unit Antenna to the Base Unit and place it where you need signal. For the widest
possible coverage area, position the Base Unit near the middle of a room. The Base Unit can be
placed on a at surface (e.g., a bookshelf, desk, end table, etc.). The Base Unit performs best when
located at least 4 feet above the oor or approximately the height of a cell phone when it is typically
in use (avoid placing the Base Unit on the oor).This Base Unit uses an omni-directional antenna
that delivers signal in a circular pattern around the antenna.
Keep the Base Unit at least 2 feet away from other cords, metal objects or other wireless devices
such as wireless routers or wireless access points. zBoost performs best when there are no
obstructions between the zBoost Base Unit and your mobile device.
Note: The Base Unit can be easily mounted on a wall by rst removing the Silver bracket from
the Base Unit (see “zBoost Base Unit Assembly” on page 7) and using 2 mounting screws (not
zBoost Base Unit
Power Supply
Base Unit Antenna
Coaxial Cable Base Unit Bracket
zBoost Base Unit Assembly

zBOOST® SOHO YX560P USER GUIDE
8
zBOOST® SOHO YX560P USER GUIDE
9
FIFTH: Antenna Aiming
To get the maximum benet, you will want to take special care to point the antenna in the direction
of the best signal for your wireless service provider. If you are able to put your phone in eld test
mode to view dB readings, results will be more accurate as cell phone “bars” can be misleading.
1. Place your cell phone on a non-metal surface which is 6-8 feet from the Base Unit Antenna.
2. Turn the signal booster on and wait 30 seconds. Note the number of signal bars displayed
on your cell phone. For best results, you want your phone to display in the middle of the
signal meter range or less so that it can go up as you rotate the Signal Antenna to the
optimum direction. If it is reading too high, move the phone farther from the base unit
antenna.
3. Record the number of signal bars (or range) ________(A) on your cell phone. Leave the
phone in the same place and pointing in the same direction for the following steps.
Note the direction of the antenna starting position_________________________.
4. Rotate the antenna mast 90 degrees and then record the phone signal bars _________(B).
5. Continue to rotate the antenna mast another 90 degrees in the same direction and record
the phone signal bars _________(C).
6. Again, rotate the antenna mast another 90 degrees in the same direction and again record
the phone signal bars _________(D).
7. Look for the highest reading above. Set the antenna to that position and tighten the antenna
hardware.
8. If you desire to optimize further, then look for the two highest signal bar readings above and
move the antenna between these two points to nd the highest signal bars reading.
9. Once you have determined the highest reading position tighten the antenna bracket
hardware.
Conrm That Your zBoost is Working Properly
1. Unplug the Base Unit power cord.
2. Turn off your cell phone.
3. Plug the power cord back into the Base Unit.
4. Hold your cell phone about 5 feet from the Base Unit and then turn it on. Wait up to 1 minute
for the cell phone to register the signal coming from the Base Unit.
5. If the signal meter shows improvement, your zBoost unit is working.
When your zBoost system is in place and fully connected, walk throughout the home and see that
you are able to reliably place calls. If the signal strength and cellular data speeds have improved,
your zBoost is working.
Remember, coverage varies based on outdoor signal level, building construction, and antenna
placement. Coverage in adjoining rooms may be reduced.
Should you desire to improve coverage, you may:
• Relocate the Signal Antenna in order to capture a better signal – higher is usually better.
• Increase the distance between the Base Unit and the Signal Antenna.
• Purchase an upgrade antenna available at www.Wi-Ex.com
NOTE: The zBoost YX560P requires at least 15 feet of vertical separation between the Base
Unit and the Signal Antenna. Generally, increasing this distance (up to 40 feet) will increase the
performance and decreasing the distance will limit zBoost performance.
Keep the Base Unit off the oor and at least 2 feet away from other cords, metal objects or other
wireless devices such as wireless routers or wireless access points. zBoost performs best when
there are no obstructions between the zBoost Base Unit and your mobile device.
Cell Tower
zBoost Base Unit
Power Supply
Base Antenna
Coax Cable
Signal Antenna
Note
Cell phone signal bars are approximate and vary from phone
to phone. The number of bars can uctuate widely, depending
on the location of the phone, the position or angle of the phone,
weather, etc. Most cell phone signal meters update every 6 to 10
seconds. An increase of only one bar typically indicates a 4x to
10x signal increase.
THE BEST INDICATOR OF PRODUCT PERFORMANCE IS THE
ABILITY TO RELIABLY PLACE AND RECEIVE CALLS WHERE
YOU COULD NOT BEFORE.
Improving Your Coverage Area

zBOOST® SOHO YX560P USER GUIDE
10
zBOOST® SOHO YX560P USER GUIDE
11
Solid GREEN Normal condition at power up.
Slowly Alternating RED and GREEN zBoost is working, but at reduced
performance and coverage due to
“non-ideal” setup.
Solution: Increase the distance
between antenna and amplier to
achieve maximum performance and
coverage.
Fast Flashing RED Indicates insufcient distance between
the antenna and the amplier. The
amplier is operating at signicantly
reduced coverage.
Solution: Increase space between
base unit and antenna.
Solid RED System is receiving signals from either
the mobile device or the base station
transceiver which are too strong for
proper operation.
Solutions:  Move away from
receiving antenna with your cell
phone.  Move antenna away from
other devices.
Fast Alternating RED and GREEN
followed by no light
The amplier is disabled.
Solution: Unplug your system and
re-power.
zBoost Base Unit Light Indicators
At Initial Power Up Only
Solid GREEN Normal condition.
Solid RED System is receiving signals from either
the mobile device or the base station
transceiver which are too strong for
proper operation.
Solution: Unplug your system. Re-
orient your Signal Antenna and/or
Base Unit to reduce the excessive
signal source. Plug your system
back in. If still solid red, call customer
support 1-800-871-1612.
After Initial Power Up
Technical Specications
Product Specications for zBoost SOHO YX560P
PCS Band
Frequency Uplink: 1850 - 1910 MHz
Downlink: 1930 to 1990 MHz
System Gain 65dB
Max Rx / Distribution Power 13 dBm
Networks CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT,
UMTS, HSPA, 3G
CEL Band
Frequency Uplink: 824 to 849 MHz
Downlink: 869 to 894 MHz
System Gain 65dB
Max Rx / Distribution Power 13 dBm
Networks CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT,
UMTS, HSPA, 3G
General
Power Consumption – Power Supply Current 3W standby; 7W max signal - 2.0A Max
System Certications FCC Parts 15 & 22, Industry Canada
Base Unit Size and Weight 5” x 7” x 1.25” – 9 oz.
Wall Supply Input ; Voltage 100-240VAC, 50-60 Hz; 5.0VDC
Operating Conditions Indoor Use Only (40° - 105° F)
Coverage (open areas) Up to 3500 square feet
This product uses patented technology to protect the carrier network
This product is covered by patent US 7,706,744. Other U.S. and
foreign patents pending.

zBOOST® SOHO YX560P USER GUIDE
12
zBOOST® SOHO YX560P USER GUIDE
13
Frequently Asked Questions
What can I expect my cell phone signal range and strength to be inside my home or ofce?
The closer you are to the base, the stronger the signal. This will vary with different conditions. Some
of the conditions that will affect the improved coverage area are signal strength outdoors, the type
of building materials in the home, the placement of the unit and the antenna’s proximity to cellular
towers.
You can expect that your indoor coverage will be improved. You will be able to make calls where
you couldn’t before. The degree of improvement will depend upon many factors. The intent of
zBoost® products are to bring outside coverage inside. Just as the signal bars move up and down
when outside, the boosted signal will uctuate in a similar fashion.
Is a cellular phone signal booster the same as a wireless router; will it help my WiFi signal?
The Wi-Ex® unit will not help your WiFi service. This unit is designed to work with wireless PCS
and Cellular phones and devices. The WiFi in your home or ofce operates on a different frequency.
Is your product available for international use?
Yes, we have a product that works on European UMTS/HSPA frequencies. zBoost® ONE YX400-U
for devices on the 2100MHz can be used for voice and data overseas.
Why isn’t my cell phone indicating more signal with more bars?
You may not always observe more bars on your signal meter because of the signal spreading out
from the antenna. If your phone has a dB meter, 3dB is a signicant increase of 2x, 6dB is 4x, and
10dB is 10x. On a four bar phone, one "bar" equals about 10dB.
The increase in signal you will see depends upon:
• The level of signal at the Signal Antenna (outdoor)
• The care of the antenna placement (two feet away from metal, adequate antenna
separation [15 feet of vertical separation is recommended])
• The signal already present inside (related to building losses)
• The distance of your phone/device from the Base Unit (signal spreads or diminishes rapidly
with distance).
There are usually several cell phones in use at one time in my home, will your product boost
all of our signals simultaneously?
This zBoost unit is designed to cover multiple signals simultaneously and will allow multiple users to
operate at the same time.
Does the zBoost work if you have no bars?
No, if no signal is present outdoors zBoost products will not work for you. Also, keep in mind if your
best signal is 1 bar at the Signal Antenna, your coverage will be limited to a small room. You can
improve that with an upgraded antenna (see page iv).
Limited 2 Year Warranty
Register your product at www.Wi-Ex.com
Wi-Ex® warrants every Wi-Ex® product to be free from defects in material and workmanship under
normal use for the warranty period of two years.
Who Is Covered?
You must have proof of purchase to receive warranty service. A sales receipt or other
documentation showing the product purchased and the purchase date is considered proof of
purchase. This limited warranty extends only to the original consumer purchaser or any person
receiving the product as a gift from the original consumer purchaser and to no other purchaser or
transferee. This warranty does NOT extend to commercial users.
What is Covered?
Warranty coverage begins the day you purchase the product. For two years from the original
date, the Wi-Ex® Cell Phone Signal Booster will be repaired or replaced with a new, repaired,
refurbished or comparable product (whichever is deemed necessary by Wi-Ex® ) if it becomes
defective or inoperative. The exchange will be made without charge to you for parts and labor. You
will be responsible for the cost of shipping to the location designated by Wi-Ex®.
All products, including replacement products, are covered only for the original warranty period.
When the warranty on the original product expires, the warranty on the replacement product also
expires.
What is Excluded?
Your warranty does NOT cover:
• Labor charges for set up of the unit.
• Product replacement because of misuse, accident, lightning damage, unauthorized repair or
other cause not within the control of Wi-Ex®.
• Incidental or consequential damages resulting from the product. Some states do not allow
the exclusion of incidental or consequential damages, so the above exclusion may not apply
to you.
• Any modications or other changes to the product, including but not limited to software or
hardware modications in any way other than as expressly authorized by Wi-Ex® will void
this limited warranty.
• Product that has been modied or adapted to enable it to operate in any country other than
the country for which it was designed, manufactured, approved and/or authorized, or repair
of products damaged by these modications.
Warranty Information

zBOOST® SOHO YX560P USER GUIDE
14
Make sure you keep…
Please keep your sales receipt or other document showing proof of purchase. Also, keep the
original box and packing material in case you need to return your product.
Before requesting repair service…
Make sure you have at least 15 feet of vertical separation between Signal Antenna and Base Unit
and that the Signal Antenna is at least 3 feet above metal.
If red light is on, system is receiving signals from either the mobile device or the base station
transceiver which are too strong for proper operation. Please unplug your system. Re-orient your
Signal Antenna and/or Base Unit to reduce the excessive signal source. Plug your system back in.
If still solid red, call customer support 1-800-871-1612.
To get warranty service…
Warranty service will be provided by Wi-Ex®. If you believe you need service for your unit,
contact Wi-Ex® at 1-800-871-1612 or [email protected]. A representative will go through a
diagnostic checklist with you. If it is determined that the product needs to be returned for service or
exchanged, you will receive a return merchandise authorization (RMA) number. The representative
will give you complete shipping details. Do not return products to Wi-Ex® without a Return
Authorization Number (RMA).
Reminder
Record the model and serial number found on the product below:
Model #: ___________________________________
Serial #: ___________________________________
Purchase Date: _____________________________