Zerhyr AK7000AS Installation guide
-81
$.$6DQG$.$6
SUHLQVWDOOHG
SUHLQVWDOOHG
IRUVLQJOHEORZHUKRUL]RQWDOGXFWLQJ
IRUVLQJOHEORZHUKRUL]RQWDOGXFWLQJ
IRUVLQJOHEORZHUKRUL]RQWDOGXFWLQJ
IRUVLQJOHEORZHUKRUL]RQWDOGXFWLQJ
LIUH XLUHGE\ORFDOFRGHV
3%'$
Suction Cup (1)
M4 x 1” (4)
M4 x 1-1/2” (4)
M4 x 2” (4)
M4 x 8 (8)
10 x 3/16” (4)
M3.5 x 8 (7)
Wire Caps (3)
Duct pieces To t a l
Equivalent number
length x used =
3-1/ 4” x 10”
Rect.,
straight
1 Ft. x ( ) = Ft.
7”-10” Round,
straight
1 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.900
elbow
15 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.450
elbow
9 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.900
flat elbow
24 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.
wall cap
with damper
30 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.to
6” round
transition
5 Ft. x ( ) = Ft.
3-1/ 4” x 10”
Rect.to
6” round
transition
900elbow
20 Ft. x ( ) = Ft.
6” Round,
900elbow
15 Ft. x ( ) = Ft.
6” Round,
450elbow
9 Ft. x ( ) = Ft.
Ft.
6” Round,
straight
1 Ft. x ( ) = Ft.
Subtotal column 1 =
Duct pieces To t a l
Equivalent number
length x used =
6” Round
wall cap
with damper
30 Ft. x ( ) = Ft.
Round
wall cap
with damper
30 Ft. x ( ) = Ft.
7” - 10”
Round,
900elbow
15 Ft. x ( ) = Ft.
7” - 10”
7” - 10”
Round,
450elbow
9 Ft. x ( ) = Ft.
Ft.
Ft.
Ft.
6” Round,
roof cap
30 Ft. x ( ) = Ft.
7” - 10”
Round,
roof cap
30 Ft. x ( ) = Ft.
Subtotal column 2 =
Subtotal column 1 =
Total ductwork =
6” round to
3-1/ 4” x 10”
rect.
transition
1 Ft. x ( ) = Ft.
6” round to
3-1/ 4” x 10”
rect.
transition
900elbow
16 Ft. x ( ) = Ft.
7” round to
3 1/ 4” x 10”
rect.
transition
8 Ft. x ( ) = Ft.
7” round to
3-1/ 4” x 10”
rect.
transition
900elbow
23 Ft. x ( ) = Ft.
11"
36"
96"
Min 26” - Max 36"
Side wall cap
w/ gravity damper
Ductless
Recirculating
Roof Pitch w/
Flashing & Cap
Rear Ducting
1 3/16”
8 9/16”
1 3/16”
2 3/16”
2 3/4”
3”
27 7/8” (30”)
33 7/8” (36”)
39 13/16” (42”)
29 15/16” (30”)
35 15/16” (36”)
41 15/16” (42”)
9 15/16”
1 1/8”
8 9/16”
13 3/16”
6 7/16”
3”
2”
12”
11”
3”
22 1/2”
29 15/16” (30”)
35 15/16” (36”)
41 15/16” (42”)
CL
ø5
7/8”
5 9/16”
elec
k/o
top side
back with 10” dual blower transition
27 7/8” (30”)
33 7/8” (36”)
39 13/16” (42”)
CL
15
5/16
”
ø 9
15/16”
14
3/16”
10
3/8
”
Cable Lock
duct/silver
tape
5. Duct
opening
cutout
3. Add 1x2
wood strips
2. Baffle
filters
2. Baffle
filters
F
Blower On/Off
Adjust 3 Speed Levels
5 Min Delay Off
Lights On/Dim/Off
Display (Speed level, Delay Off Indicator)
1
2
3
45
Blower On/Off
By pressing , the blower is switched On and Off. When switched on, the blower turns on at the same
speed it was switched off at. When switched off the entire hood powers off, including the lights.
Speed Selection
The 3 speed levels are selected by pressing to decrease and to increase speed level. The
display indicates speed level selected. Pressing when the hood is off will also turn it on.
Delay Off
This is used for programmed shut down of blower and lights 5 minutes after the function is
activated. Press once, a dot displays in the lower right hand side of display indicating
the function is on. The hood will change to speed 1 and shut down after 5 minutes.
Lights On/Dim/Off
Switch lights On by pressing once, again to dim and again to switch Off.
Baffle Filter Clean Reminder
After every 30 hours of use the display will start flashing an reminding you to clean the baffle filters
from residue and possible clogs.
1
2
3
4
Display
Displays blower speed level, delay off status and filter clean/replace notification.
5
Heat Lamps On/Off
Located on the right and left side light panel are manual power on/off toggle switches. These
switches are used to turn the heat lamps on/off. Toggle between I (on) or 0 (off).
Charcoal Filter Change Reminder (charcoal filter, if installed)
When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust
and fumes from cooking, then re-circulates the air within the home. These charcoal filters are required to
be replaced after every 120 hours of use. The charcoal filters should never be cleaned or placed in a dish
washer.
The filter change reminder function in the microprocessor needs to be switched on. When switched on, the
microprocessor will elapse and count usage time and indicate by a flashing when charcoal filter
replacements are needed.
&
Setting the Filter Change Reminder
When off, hold for approximately 5 seconds.
The display will change from (exhaust mode) to
(recirculating mode) this indicates that the
elapse timer function is switched on and charcoal
filters are used.
Filter Replace Indicator
When the display starts flashing, the charcoal
filters need to be replaced.
Re-setting Function
Once filters are replaced, with hood off, press and
hold the display will appear; hold for apprimately
5 seconds until on displays disappears .
The filter change reminder is now re-set and a new
120 hour elapse cycle is initiated.
&
&
&
&
hold 5 sec. display from < - > to < C >
Set Mode
Set Mode
display < C > flashes
Change FIlters
&
hold 5 sec. display from < C > to < >
To Reset
&
Baffle Filter Clean Reminder
Whether your hood is installed as an exhaust or purifying unit, a set if baffle filters are fitted by the fact
o
These baffle filters are intended to filter out residue from cooking. They need not be replaced on a reg
u
basis but are required to be kept clean. The filter clean reminder function in the microprocessor will
automatically indicate by a flashing when the baffle filters need to be cleaned after every 30 hour
s
use. Filters can be cleaned by hand with non-abrasive soap or in a dishwasher. Heavily soiled filters
should also be soaked in grease cutting detergent prior to cleaning.
Baffle Filter Clean Indicator
When flashes on display, the baffle filters
installed are required to be cleaned. This will occur
after every 30 hours of use.
Re-setting Function
Reset the filter clean reminder timer when filters are
cleaned and re-installed (with hood off). Press and
hold for approximately 5 seconds, the display will
appear; hold for approximately 5 seconds until on
display disappears . The filter clean reminder
function is now reset and a new 30 hours elapse
cycle is initiated.
FClean Filters
display < F > flashes
F
hold 5 sec. display from < F > to
<
To Reset
F
F
F
This manual suits for next models
2
Table of contents
Other Zerhyr Ventilation Hood manuals
Popular Ventilation Hood manuals by other brands
Eizo
Eizo Monitor Hood CH4 user manual
Franke
Franke FDF H60 9156 I XS LED0 Instructions for use and installation
Universal Metal Industries
Universal Metal Industries Trade-Wind S7236CD Installation instructions & use & care guide
Fulgor Milano
Fulgor Milano F4 UC30 S1 Instructions for installation and use
Wolf
Wolf Pro Wall Series installation guide
Garwoods
Garwoods HT-50900S Installation & operation manual
