Zetti Coast User manual

`
USER GUIDE: Coast
Welcome to the Zetti Team!
We want to ensure you get the most of our incredible products so please read
the directions carefully. If you have any specific concerns or questions please
reach out to our customer support.
● Website: www.zettibrand.com
● Email: [email protected]
● Facebook: www.facebook.com/thezettibrand/
● Instagram: @zettibrand
Also be sure to share your awesome experiences with our products! Tag us on
your favorite social platforms or simply email us directly with any of your favorite
images, videos, and stories.
1

`
INCLUDED COMPONENTS (Full Hydrofoil)
● Carrying Bag
● Mast
● Fuselage
● Front wing(s)
● Rear wing
● Stainless Steel T-nut
● Torx L-Key driver
2

`
INSTRUCTIONS
Assemble Hydrofoil
1. Remove foil components from bag
2. Remove torx keys and mounting hardware
Reference table below for correct combinations
Front wing
3x
M8x25mm
Rear wing
2x
M6x25mm
Mast
4x
M8x35mm
T-Nut
4x
M8x22mm
3. Assemble front and rear wing to fuselage
● Add foil covers to protect carbon wings from
accidental damage
4. Add Top plate to Mast
5. Add mast assembly to fuselage assembly
6. Mount to board
● See instructions for pairing with Airship inflatables
● Don’t forget to remove covers before use!
3

`
Attach Hydrofoil (Zetti Coast) to Board (Airship)
1. Assemble Hydrofoil mast, base, fuselage and
wings according to manufacturer spec
2. Turn inflated board over on clean
flat surface
3. Add included M8x22mm screws into each
t-nut and rotate 1 full turn
4. Insert T-nut assembly into US Box
(2 each) and move to all 4
corners of track
5. Place hydrofoil on top of the carbon plate
● Make sure to stabilize the mast with one hand to
keep foil upright during this process.
6. Move screws through the slots and into
the countersunk recession on the mast
base
7. Move to desired location and tighten screws
8. Check tightness of all screws
● Go ride!
● Adjust mast location as necessary
for your weight, riding style, and foil
4

`
ASSEMBLY NOTES:
Zetti Airship uses industry standard 9cm track, and is compatible with most brands on the market.
Please ensure the mast plate screw lengths and T-nut threads are the correct size. Failure to do so can
cause damage to the board upon installation.
* Some hydrofoils do not have slots and must be attached by these following steps - beginning after step
3 on the previous page:
1. Carefully place the mast base over the T-nuts
2. Insert M8 screw through the hole on the mast base and then screw into the t-nut
3. Repeat for all 4 screws
4. Move foil base into desired location
5. Tighten screws
RECOMMENDATIONS
HYDROFOIL CARE:
● To ensure longevity of components it is recommended to use anti-seize thread grease on the
screws during assembly
● During each session occasionally check to ensure screws have remained tight
● After each session disassemble the hydrofoil for storage in included carrying case
○ Remove Stainless screws from the aluminum mast and fuselage
■ Failure to do so may cause the screws to corrode and seize
■ This is especially important in salt water environments
■ Note: using titanium screws considerably eliminates any possible
corrosion
● These can be purchased separately
○ Rinse all parts in fresh water and allow to dry before long term storage
5

`
SAFETY AND RELEASE OF LIABILITY
Zetti hydrofoil boards, hydrofoils, wings and other products are used in sports that are considered
inherently dangerous. Any use of Zetti Brand products releases Zetti Brand, LLC from liability from
damage or injury caused by improper use, pre-existing damage, extreme wear and tear, or adverse
weather conditions. Please follow directions and safety recommendations carefully!
Inflate board to recommended pressure of 15-20psi and be sure to check that the valve is in proper
working order. Make sure the valve is closed properly before use.
Do not go further from shore than you are willing to swim back. If the board deflates there is no extra
flotation compartment.
Use included board leash at all times. It is very easy to become separated from your board without a
leash. Under extreme circumstances it may be necessary to disconnect from your board to prevent
injury, for example, in large breaking swell. Please do so carefully, and have a plan to return to shore
before release.
It is recommended to always wear a wetsuit and Personal Flotation Device (PFD) or lifejacket while
using our products. Please follow local laws and practice in safe locations away from marine traffic.
Minors must have adult supervision at all times while using the product.
6

`
WARRANTY
Please review the package upon receipt and inspect for damage or manufacturing defects prior to first
use.
If defects are found please reach out to Zetti support immediately and we will work out a warranty
replacement. This warranty replacement does not apply if the product was purchased with prior
knowledge of defect or is due to materials added or mishandling of product.
We will happily accept returns within 30 days from the date of delivery if the product is in an unused and
undamaged condition.
All of our products are guaranteed for 90 days from the date of delivery from manufacturing defects.
Limitations of Warranty
We manufacture our products with the highest quality of components and control. While we take care to
make sure the highest quality product is shipped to our customers we cannot cover all damage incurred
to the Product, and we must exclude:
● Normal wear and tear
● Damage caused by overpressure
● Impacts, scratches, or damage caused by foreign objects
● Damage caused by collisions
● Overexposure to UV, sun, salt, or humidity
● Improper storage
● Damage caused by waves, shorebreak, or extreme weather
● Damage caused by non-approved repair; professional or otherwise
● Damage caused by unintended use of the Product; ie: rafting or towing behind boat
● Damage caused by improper mounting outside of recommendations
● Damage or personal injury to the user while using the Product
● Damage or personal injury caused by the user to others when using the Product
Warranty is only valid if product is used for its intended purpose; Wingfoil, Surfoil, Supfoil, Wakefoil, or
Kitefoil in leisure and does not cover products used for hire or in competition.
Note:
During a crash the board may flip upside down exposing the hydrofoil. As the board rolls back, the
hydrofoil may contact the user or puncture the wing canopy or bladder. Do your best to prevent high
speed or extreme crashes that can result in these conditions. This is a common occurrence during
foiling and is not covered by warranty.
7

`
8