Franklin DELUXE User manual

Return Trainer
Pitch Target
DELUXE 2 in 1
Throwing & Pitching
Combo Set
Item #2719
Step 6:
Before putting the net on the frame, secure part (2), “Infinite Adjustment” system by
screwing onto pole counter clockwise. To attach net part (11) to frame, spread out net
and find red tabs attached to net. The red tabs indicate the corners of the net. To attach
net, start with one corner and attach with one bungee, then attach the other three
corners. Next, start at the top of the frame and attach the bungees across the top
spreading them evenly. Attach the bungees on one side spreading them evenly. Repeat
on bottom and then on final side.
Step 8:
Attach target ribbon part
(12) by weaving through
net and tying off at
ends.
Step 7:
To attach bungees to net
hold plastic ball in place
and wrap free end around
net and side tube. Loop
free bungee around plastic
ball.
For Replacement Parts Call 1-800-225-8649
MA Residents Call 1-781-341-5178
FRANKLIN SPORTS INC. Stoughton, MA 02072 www.franklinsports.com
Note: Do not extend
“Infinite Angle” adjustment
system beyond red
indicator mark on tube.
TOOLS REQUIRED:
FLAT OR PHILLIPS SCREWDRIVER
Step 9:
Attach catcher target, part
(13), to bunees on other side
of return. Place bungee
hooks into metal holes
around the outside of target
screen.
Step 10:
Attach collection bag, part
(14), to clips on front of
catcher target.
Step 11:
To draw back target,
attach back straps to the
back brace pole.
ISO 4/08
Use extreme caution when assembling
the net to the frame. The bungees will
be under extreme tension and must be
attached carefully. Adult assembly is
strongly recommended.
Note: To fold flat for easy storage, depress push
pins on part (6) and release support arm. Unit
will now fold flat.

Step 2:
To make the frame for the net, use one of the “U” shaped tubes, part (1), and slide four
of part (9) onto part (1). Then place a side pole from step 1 into the open end of part (1).
Take the second side pole and place into the other open end. Next, use the second “U”
shaped tube, part (1), and attach two ends of the side poles. You should now have a
rectangle shape.
Step 3:
First place 4 hooks part (9) on part (1) as indicated in photo. To make the base, use the
third “U” shaped tube, part (1), and place part (5) into one of the open ends. Slide 4
ground stakes, part (10), onto assembly. Position ground stakes as shown. Repeat on
other side. Next, attach side supports part (6) to base on outside of the “U” shaped
tubing where the pre-drilled holes are. Make sure the pre-drilled holes are lined up on
the “U” shaped tubing and part (5) before attaching part (6). Attach by using bolt and
wing nut part (7). Repeat on other side.
Step 4:
To attach net frame to base assembly, take the net frame and place between the open
end of base. Line up the pre-drilled holes on the net frame to part (5) on the base assem-
bly and attach by using bolt and wing nut part (8) on both sides. Next, use part (2) and
attach to the top outside of the net frame where pre-drilled holes are. Make sure the
pre-drilled holes are lined up on the “U” shaped tubing and you attach the narrower end
of part (2) to the top of the net frame using part (7).
Step 1:
Make net frame side by placing part (3) into part (4) and snapping push pins into place.
14
15
13
Step 5:
Attach the bottom of part (2) to the back of
the base by inserting part (6) into part (2) by
lining the pushpin up with the pre-drilled hole.
Replacement Parts
Part Amount Description Replacement Part #
1 3 pcs 44” U-Shaped Tubes 2770Z9
2 2 pcs Adjustable Tube 2770Z11
3 2 pcs 26” Straight Tubes 2770Z3
4 2 pcs 26” Straight Tubes 2770Z4
5 2 pcs 34” L Shaped Tube 2770Z5
6 2 pcs 3.5” Straight Tubes 2770Z6
7 4 pcs 2” Butterfly Screws 2770Z7
8 2 pcs 2 3/8” Butterfly Screws 2770Z8
9 8 pcs Hooks 2770Z1
10 4 pcs Ground Stakes
11 1 pc Net 2770Z2
12 1 pc Target Ribbon
13 1 pc Pitch Target
14 1 pc Collection Bag
15 22 pcs Bungees 2770Z13
DIAGRAM #1
DIAGRAM #2
DIAGRAM #3
DIAGRAM #4
DIAGRAM #5

Step 2:
To make the frame for the net, use one of the “U” shaped tubes, part (1), and slide four
of part (9) onto part (1). Then place a side pole from step 1 into the open end of part (1).
Take the second side pole and place into the other open end. Next, use the second “U”
shaped tube, part (1), and attach two ends of the side poles. You should now have a
rectangle shape.
Step 3:
First place 4 hooks part (9) on part (1) as indicated in photo. To make the base, use the
third “U” shaped tube, part (1), and place part (5) into one of the open ends. Slide 4
ground stakes, part (10), onto assembly. Position ground stakes as shown. Repeat on
other side. Next, attach side supports part (6) to base on outside of the “U” shaped
tubing where the pre-drilled holes are. Make sure the pre-drilled holes are lined up on
the “U” shaped tubing and part (5) before attaching part (6). Attach by using bolt and
wing nut part (7). Repeat on other side.
Step 4:
To attach net frame to base assembly, take the net frame and place between the open
end of base. Line up the pre-drilled holes on the net frame to part (5) on the base assem-
bly and attach by using bolt and wing nut part (8) on both sides. Next, use part (2) and
attach to the top outside of the net frame where pre-drilled holes are. Make sure the
pre-drilled holes are lined up on the “U” shaped tubing and you attach the narrower end
of part (2) to the top of the net frame using part (7).
Step 1:
Make net frame side by placing part (3) into part (4) and snapping push pins into place.
14
15
13
Step 5:
Attach the bottom of part (2) to the back of
the base by inserting part (6) into part (2) by
lining the pushpin up with the pre-drilled hole.
Replacement Parts
Part Amount Description Replacement Part #
1 3 pcs 44” U-Shaped Tubes 2770Z9
2 2 pcs Adjustable Tube 2770Z11
3 2 pcs 26” Straight Tubes 2770Z3
4 2 pcs 26” Straight Tubes 2770Z4
5 2 pcs 34” L Shaped Tube 2770Z5
6 2 pcs 3.5” Straight Tubes 2770Z6
7 4 pcs 2” Butterfly Screws 2770Z7
8 2 pcs 2 3/8” Butterfly Screws 2770Z8
9 8 pcs Hooks 2770Z1
10 4 pcs Ground Stakes
11 1 pc Net 2770Z2
12 1 pc Target Ribbon
13 1 pc Pitch Target
14 1 pc Collection Bag
15 22 pcs Bungees 2770Z13
DIAGRAM #1
DIAGRAM #2
DIAGRAM #3
DIAGRAM #4
DIAGRAM #5

Return Trainer
Pitch Target
DELUXE 2 in 1
Throwing & Pitching
Combo Set
Item #2719
Step 6:
Before putting the net on the frame, secure part (2), “Infinite Adjustment” system by
screwing onto pole counter clockwise. To attach net part (11) to frame, spread out net
and find red tabs attached to net. The red tabs indicate the corners of the net. To attach
net, start with one corner and attach with one bungee, then attach the other three
corners. Next, start at the top of the frame and attach the bungees across the top
spreading them evenly. Attach the bungees on one side spreading them evenly. Repeat
on bottom and then on final side.
Step 8:
Attach target ribbon part
(12) by weaving through
net and tying off at
ends.
Step 7:
To attach bungees to net
hold plastic ball in place
and wrap free end around
net and side tube. Loop
free bungee around plastic
ball.
For Replacement Parts Call 1-800-225-8649
MA Residents Call 1-781-341-5178
FRANKLIN SPORTS INC. Stoughton, MA 02072 www.franklinsports.com
Note: Do not extend
“Infinite Angle” adjustment
system beyond red
indicator mark on tube.
TOOLS REQUIRED:
FLAT OR PHILLIPS SCREWDRIVER
Step 9:
Attach catcher target, part
(13), to bunees on other side
of return. Place bungee
hooks into metal holes
around the outside of target
screen.
Step 10:
Attach collection bag, part
(14), to clips on front of
catcher target.
Step 11:
To draw back target,
attach back straps to the
back brace pole.
ISO 4/08
Use extreme caution when assembling
the net to the frame. The bungees will
be under extreme tension and must be
attached carefully. Adult assembly is
strongly recommended.
Note: To fold flat for easy storage, depress push
pins on part (6) and release support arm. Unit
will now fold flat.