manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Zico
  6. •
  7. Rack & Stand
  8. •
  9. Zico Quic-Release QR-SOFD-2 Quick setup guide

Zico Quic-Release QR-SOFD-2 Quick setup guide

ZICO®
3030PM26
®


 
  

Important: Bearing Blocks (39) must be installed to meet SAE compliance.
Page 2
ITEM
   
1 3030-160-101 Stationary Housing 1
2 3030-160-103 Slider, Main 1
3 3030-160-105 Slider, Extension 1
4 3030-160-107 Stop Bar 1
5 3030-160-109 Spacer Block 1
6 9014-183100 5/16 Flatwasher, GR8 34
9 3030-160-117 Hinge, Ref: MMC 15665A336 1
11 3030-160-125 Wear Strip, Main 2
12 3030-160-123 Handle, SS (MMC 11665A31) 1
13 9015-102510 Screw, 1/4-20 x 5/8, Hex Hd. 6
14 9013-172501 Hex Nut, 1/4-20 Nylon Low-Pro 6
19 9010-103124 Screw, 5/16-18 x 1-1/2 Hex Hd. 2
20 9015-173100 Hex Nut, 5/16-18 Self Lock, GR5 20
24 9015-183100 Hex Nut, 5/16-18 2
26 9015-103116 Screw, 5/16-18 x 1 Hex Hd, GR5 16
27 9010-162010 Screw, 10-32 x 5/8 82° FH 26
28 9013-172000 Nut, 10-32 Hex, Nylon Loc 26
30 3030-160-127 Wear Strip, Short 2
34 3030-160-131 Pin Bracket 1
35 3030-160-133 Pin, Lock 1
36 3030-160-135 Spring, Pin, Lock 1
37 9040-111212 Roll Pin, ø1/8 x 3/4, SS 1
38 0000-000-123 Key Ring, .142 Thk x 1.48 OD ZP 1
39 3030-160-139 Bearing Block 2
40 9010-462510 Screw, Torx, 1/4-20 x 5/8 100° FH 6
42 9014-112500 Washer, 1/4 Flat 6
43 3030-163-101 Lock Pin Shield 1
Unit Weight: 46 lbs

ITEM
      
6 9014-183100 5/16 FLATWASHER, GR8 32
20 9015-173100 HEX NUT, 5/16-18 SELF LOCK-GR5 16
26 9015-103116 SCREW, 5/16-18 x 1" HEX.-GR5 16
27 9010-162010 SCREW, 10-32x5/8 100 FH 4
28 9013-172000 NUT, 10-32 HEX, NYLON LOC 4
39 3030-160-139 BEARING BLOCK 2
40 9010-462510 SCREW, TORX, 1/4-20x5/8 100 FH 6


ITEM
   
34 3030-160-131 PIN BRACKET 1
35 3030-160-133 PIN, LOCK 1
36 3030-160-135 SPRING, PIN, LOCK 1
37 9040-111212 ROLL PIN, ø1/8 x 3/4, SS 1
38 0000-000-123 KEY RING, .142 THKx1.48OD ZP 1
NOTE: ALL "PACKED SEPARATELY" ITEMS SHOWN
ABOVE HAV BEEN ACCOUNTED FOR IN THE MAIN BILL
OF MATERIALS.

Page 3

Page 4

Page 5
Note: Numbers in parentheses correspond to numbers in Parts List for ease of assembly.

1. Roughly position the QR-SOFD-2 in the apparatus. See Figure 3 (with QR-MV) or Figure 4 (with
QR-GH) for overall height dimensions. Note that these dimensions do not include the Gas Cylinder.
2. Decide which side, LH or RH, is best position for the pre-assembled Lock Assembly (34) (35) (36) (37) (38).
See Figure 1, Detail “A”.
3. Attach the Lock Assembly to the Stationary Housing (1). See Figure 1, Detail “A”.
Important: The Bearing Blocks (39) and Screws (40) attached in in the following step must be on the same side
of the Latch Assembly.
4. Attach the Bearing Blocks (39) using Screws (40) supplied to the Main Slide (2). See Figure 1,
Detail “B”.

 1.PositiontheQR-SOFD-2intheapparatus.CheckfortandfunctionbyusingtheHandle(12)topull 
the Main Slider (2) out. Allow for the Slider to fold down. Check for any interference with the
apparatus.
2. Keeping the unit in the extended and folded down position, mark and drill the hole mounting
locations shown in Figure 2.
3. Mount the Stationary Housing (1) to the Apparatus using 8 sets of GR5 5/16 bolts, washers and nuts
(not supplied).

Note: See Figure 3 for the following steps and refer to the QR-MV manual.
1. The positions of the brackets in Figure 3 are spaced for G and H Gas Cylinders.
2. Mount the four brackets as shown using 16x GR5 5/16-18 Hex Head Screws (26), washers (44) and
Nuts (20).
3. Attach the four Strap and Buckle Assemblies. Refer to the manual that is supplied with the bracket.
 
Note: See Figure 3 for the following steps and refer to the QR-MV manual.
1. Position and fasten the QR-MV’s Base Plate Assembly to the QR-SOFD-2 Main Slider (2) using 6x
GR5 5/16-18 Hex Head Screws (26), washers (44) and Nuts (20).
2. Position QR-MV’s Retainer Assembly to the approximate height of the Gas Cylinder on the
QR-SOFD.
3. Place an empty gas cylinder into the bracket.
 4.LocatetheRetainerAssemblysothattheStopisattheneckofGasCylinder.Checkfortand 
function of the Gas Cylinder in the bracket.
5. Fasten the Retainer Assembly using 6x GR5 5/16-18 Hex Head Screws (26), washers (44) and Nuts
(20). Drill Ø11/32 holes if necessary to make sure that the Retainer Assembly has 6 fasteners securing it
to the Main Slider (2).
6. See Figure 3 for the locations of the two Support Straps.
7. Fasten a Support Strap using 2x GR5 5/16-18 Hex Head Screws (26), washers (44) and Nuts (20).
Repeat for the other Support Strap.
8. Attach the four Strap and Buckle Assemblies. Refer to the manual that is supplied with you bracket.
Page 6
 
Note: See Figure 4 for the following steps and refer to the QR-GH manual.
1. Position the bracket as shown.
2. Mount the bracket using 6x GR5 5/16-18 Hex Head Screws (26), washers (44) and Nuts (20).
3. Attach the 3 Straps. Refer to the manual that is supplied with the bracket.
 Gas Cylinders are heavy and bulky. Personal injury can occur during Gas Cylinder change over.
Use caution during the changeover and when lowering the Main Slider (2) to the ground.
 
1. Pull out the Key Ring (38) to unlock the lock. Use the Handle (12) to pull out the Main Slider (2) and
allow for the Slider to fold down and rest on the ground.
2. Place the Gas Cylinder into the bracket.
3. Secure the straps around the Gas Cylinder.
4. Connect the supply line to the Gas Cylinder valve.
5. Turn the supply line valve on.
6. Turn the Gas Cylinder valve on.
Important:
 
7. Use the Handle (12) to lift up the Main Slider (2) into a horizontal position. Push the Main Slider into the
stowed position of the apparatus.
Important: Make sure that the Pin (35) of the Lock Assembly is engaged into the opening of the Main Slider
(2). See Figure 1, Detail “B” for location of the opening. Test the engagement by pulling on the Handle (12) and
making sure that the Main Slider does not pull out.
 
1. Pull out the Key Ring (38) to unlock the lock. Use the Handle (12) to pull out the Main Slider (2) and
allow for the Slider to fold down and rest on the ground.
 2.ShuttheGasCylindervalveo.
 3.Shutthesupplylinevalveo.
4. Disconnect the supply line at the top of the Gas Cylinder.
5. Remove Stop at the neck of the Gas Cylinder.
6. Undo the straps.
7. Remove the Gas Cylinder from the bracket.
Important: Before replacing the Gas Cylinder, inspect the straps and the bracket components for any damage.
Replace parts if needed.
Page 7
Ziamatic Corp.
    
.

  
Page 8

Other Zico Rack & Stand manuals

Zico Quic-Mount VM-3RS-D Parts list manual

Zico

Zico Quic-Mount VM-3RS-D Parts list manual

Zico SURE-GRIP SG-VM-1 Parts list manual

Zico

Zico SURE-GRIP SG-VM-1 Parts list manual

Zico QUIC-MOUNT QM-SBH Parts list manual

Zico

Zico QUIC-MOUNT QM-SBH Parts list manual

Zico QUIC-MOUNT QM-ETD-1 Parts list manual

Zico

Zico QUIC-MOUNT QM-ETD-1 Parts list manual

Zico SURE-GRIP XL SG-VM-XL Parts list manual

Zico

Zico SURE-GRIP XL SG-VM-XL Parts list manual

Popular Rack & Stand manuals by other brands

LD DAVE G4X T-BAR S Assembly instructions

LD

LD DAVE G4X T-BAR S Assembly instructions

Kreg Metric quick start guide

Kreg

Kreg Metric quick start guide

ENDORFY EY0A006 quick start guide

ENDORFY

ENDORFY EY0A006 quick start guide

Kendall Howard 8U - 1915-3-001-08 installation instructions

Kendall Howard

Kendall Howard 8U - 1915-3-001-08 installation instructions

Novopro SMS80R instruction manual

Novopro

Novopro SMS80R instruction manual

BIN WAREHOUSE JAN21 Assembly instructions

BIN WAREHOUSE

BIN WAREHOUSE JAN21 Assembly instructions

LG T8 installation guide

LG

LG T8 installation guide

Miele PFD 101i quick start guide

Miele

Miele PFD 101i quick start guide

BRKT FLT3260FULL-LVL instruction manual

BRKT

BRKT FLT3260FULL-LVL instruction manual

American International LXSK1315 quick start guide

American International

American International LXSK1315 quick start guide

Atdec 8060 installation guide

Atdec

Atdec 8060 installation guide

JARDINICO JCP.4 Series Assembly and user's manual

JARDINICO

JARDINICO JCP.4 Series Assembly and user's manual

Loxit 8996 manual

Loxit

Loxit 8996 manual

Unior 1693EL user manual

Unior

Unior 1693EL user manual

Arctic W1B Welcome guide

Arctic

Arctic W1B Welcome guide

Richelieu Classic CID32 Assembly and Instruction Guide

Richelieu

Richelieu Classic CID32 Assembly and Instruction Guide

Atdec AWM-P G installation guide

Atdec

Atdec AWM-P G installation guide

CHIEF FCA613 installation instructions

CHIEF

CHIEF FCA613 installation instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.