zobelle Z-GR User manual
GR
ZO... WHAT ARE YOU
WAITING FOR?
GET ZAPPING!
GR
Contents.
3 PRODUCT OVERVIEW.
3 DISPLAY SCREEN.
4 HOW TO USE.
5 TREATMENT MODES.
6 AFTERCARE.
6 CLEANING, MAINTENANCE AND STORAGE.
7 INTENDED USE OF ZOBELLE™ COOLING IPL HAIR REMOVER.
8 SKIN TONE & BODY HAIR TYPE CHART.
10 IMPORTANT SAFETY INFORMATION.
Product Overview.
1. Zobelle™ Cooling IPL
Hair Remover device
2. Intensity level button
3. Display screen
4. Contact Surface
5. Cooling feature button
6. Trigger button
Display Screen.
1. Number display
2. Intensity level
3. IPL mode
4. Cooling feature
PLEASE READ CAREFULLY BEFORE USE
IPL targets melanin which is suitable for mo skin colours except for very dark skin.
It is mo suitable for those who have darker hair and fairer skin. It is safe to use for
people with tattoos and freckles/moles, however, going over tattoos/freckles/
moles is not recommended.
1
2
1
2
6
5
3
4
4
3
How To Use.
PREPARATION
1. If the hair in the treatment area is more than 2mm long, you should remove it for optimal
results. To do so, shave the area with the razor provided a minimum of
24 hours before treatment.
2. Shave as you would normally and try not to use any new products that you have not yet
teed. We do not recommend dry shaving the area this is to avoid any irritation to the
skin. You do not need to shave the hair in the area if it is not longer than 2mm.
3. Before treatment, you mu ensure the skin is hair-free, clean, dry and free from
all lotions, oils, moiurisers, fake tan and other products.
CONDUCT A PATCH TEST
1. Before your fir treatment on each new body area, we recommend you te
your skin (in that area) for reactions.
2. The patch te area should be approximately 3 cm x 2 cm in size (equivalent to
2 flashes applied to the skin side by side).
3. Wait 24 hours following the patch te, to ensure your skin is suitable for treatment and
there is no adverse reaction to the light energy. If there is no reaction after 24 hours,
you may treat the area around the te patch. The ‘patch teed area’ should not be re-
treated for at lea one week.
HOW TO USE ZOBELLE™ COOLING IPL HAIR REMOVER DEVICE
1. Plug the mains cord into an electrical outlet. Plug the power supply into the power socket.
You will see the device flash 3 times before the screen displays ‘OFF’.
2. To turn the device ‘ON’, press the trigger button (see diagram) and hold for
1.5 seconds. Keep the power cord plugged in throughout your treatment. The device can
be used plugged in and does not need to be charged in advance. The device is not
rechargeable.
3. The default intensity setting on the device is ‘1’ which is the lowe level.
To increase this, short-press the intensity level button (see diagram) to cycle through the
settings and op on the intensity level you would like to choose.
4. The cooling feature is not on by default. To activate it (optional), short-press the cooling
feature button (see diagram) and you will see the fan icon appear on the screen. To turn
off, press the same button and the icon will disappear.
5. The IPL feature is not on by default. If you would like to activate it, press and
hold the trigger button (see diagram) for 1.5 seconds and you will see the IPL mode icon
appear on the screen. To turn off, press the same button and the
icon will disappear.
6. “Energy orage” indicates how many flashes are left in the device.
7. When the device has not been used in 5 minutes, it will automatically turn off for your
safety.
WHAT INTENSITY LEVEL SHOULD YOU USE?
We recommend patch teing this device 24 hours before use on level 1 (the lowe intensity
level) then waiting 24 hours to ensure your skin does not have any adverse reactions.
For fir time use, we recommend not exceeding intensity level 4.
Treatment Modes.
The device has two treatment modes ‘Press and Flash’ and ‘Slide and Flash’, which you can
change depending on which area you are treating.
1. Press and Flash mode is recommended for treating sensitive or small, hard-to-reach
areas such as knees, shins, ankles, bikini line or underarm. Simply press the trigger button
to activate.
2. Slide and Flash mode is ideal for larger areas such as legs. Simply press the trigger
button and hold whil gliding the device across the treatment area. The device will
deliver multiple continuous flashes so you can treat larger areas with ease. Ensure you
keep moving the device and do not ay in the same spot.
IM PORTANT
1. In both modes, the area to be treated has to be hair-free, clean and dry. Before pressing
the treatment button, look away from the device to avoid the bright light.
2. Make sure to avoid missed areas by placing the treatment window directly next to the
previously treated spot without leaving any space between treated areas.
3. If you feel intense pain, op treatment immediately and consult your physician before
using the device again.
4. Ensure that the entire area receives treatment, but DO NOT treat an area twice
(overlapping flashes).
HOW OFTEN CAN YOU USE THE ZOBELLE™ COOLING IPL HAIR REMOVER?
The recommended usage is:
1. Once per week for 12 weeks
2. Once per month every 3 months after that
3. Once every 2-3 months as required after that
Table of contents
