Zorg 3202 Installation instructions

Page 2
Features & Specification
3202
Image device:
1/3" CMOS BSI 1280H x 960V pixels
Scanning system
PAL & NTSC Automatic
Video frame rate
25fps / 30fps
Operating voltage
DC 9V-36V
Consumption (IR LED on)
< 2.5W
Lens angle
130 degree diagonal
Microphone
Yes
Infrared LEDs
6 (10m visibility)
IR LED switch control
Photo sensor automatic control
Housing
Aluminum alloy
Mechanical vibration
10G
Mounting
Permanent tilt bracket
Weight
430g
Operating temperature
-40℃to +85℃
Ingress protection
IP68
Required Tool List Supplied Parts list
Screwdrivers Wireless camera with power cable
Marker pencil Installation screws/clips
Drill Antenna rubber stoppers
Plyers
Voltmeter
Safety Glasses

Page 3
Attach Antenna & Rubber Stopper
1. Screw antenna on the base
2. Align the antenna to allow it to point straight up.
3. Adjust antenna as desired. It is recommended that the antenna be aligned
straight up for the best reception.
Camera Installation
The 3202 Wireless Camera installation is simply a matter of bolting the
camera onto the vehicle and supplying reverse power (DC 9V-36V). The only
issue to take into account is the mounting location. There are three main
factors to consider:
1.Wireless Performance –The wireless communication cannot pass through
metal, so it is always better to install the camera near the top of the vehicle or
as low as possible so that the signal can effectively travel over the top or
under the vehicle.
2.Viewing Angle –The installation's primary goal is to ensure the driver has a
complete view of the area behind the vehicle.
3.Protection –In harsh environments, please ensure the hardware is
adequately protected from exposed harsh elements.
Wiring
1. Connect the RED wire to Positive ACC power 9-36vdc
2. Connect the BLACK wire to Ground ( Negative).
See the 3201 Monitor Instructions for pairing and other
setup details. Available at www.zorg-na.com

Page 4
FCC Declaration of Conformity
Test Standards and Results
The EUT has been tested according to AS/NZS 4268:2010(Refer to ETSI EN
300 328 v1.7.1. (2006-10))
ETSI EN 300
328
V1.1.1 (2006-10)
Electromagnetic compatibility and Radio spectrum Matters (ERM);
Wideband Transmission system; Data transmission equipment in
the 2.4GHz ISM band ad using spread spectrum modulation
techniques: Part2: Harmonized E covering essential requirements
under article 3.2 if the R& TTE Directive
This product has been tested to ensure open area radio transmission
up 200 meters.
This device complies with Part 15 of the FCC rules. Operation is
subject to the following conditions, (1) this device may not cause
harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the instructions,
the product may cause disruptive interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or other equipment reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to a different power source from the receiver.
Consult the dealer or an experienced radio technician for help.
Changes or modifications not expressly approved by the party
responsible for compliance could avoid the user's authority to operate
the equipment

Page 5
Warranty
The Company (Zorg North America) warrants that if this product or any part thereof, under regular use, be
proven defective in material or workmanship within 36 months from the date of original purchase, such defect(s)
will be repaired or replaced with a new or reconditioned product (at the Company's option) without charge for
parts and repair labor. The Company will not be responsible for more than the original product cost. Shipping is
not covered. Contact your Vehicle Upfitter, Body or Chassis Builder, or Vehicle converter for warranty coverage
or information.
This product is NOT covered under the OEM vehicle warranty. Zorg North America will not be
responsible for 3rd party (Car Dealer) diagnostic or labor charges.
What is not covered? This warranty does not cover the following:
•Damage incurred during shipping or transporting the product to the Company or a service center.
•Elimination of car static or motor noise
•Defects in cosmetic, decorative or non-operative structural parts.
•Costs incurred for installation, removal, or re-installation of the product or consequential damage to
accessories or vehicle electrical systems.
•Damage caused by improper installation, mishandling, misuse, neglect, accident, blown fuses,
battery leakage, theft, or improper storage.
•Products whose factory serial number/bar code label(s) or markings have been removed or defaced.
•Damage resulting from moisture, humidity, excessive temperature, extreme environmental
conditions, or external natural causes.
•Shipping to Zorg North America for Service or replacement.
Any return must be pre-authorized by Zorg North America, or it will be returned freight-collect without
repair.
Limitations
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AND IN NO EVENT SHALL THE COMPANY'S LIABILITY EXCEED THE
PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This warranty is in place of all other express
warranties or liabilities. ANY IMPLIED WARRANTIES INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY
ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY, MUST BE BROUGHT WITHIN 36 MONTHS FROM DATE OF ORIGINAL PURCHASE.
IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED, WHATSOEVER. No person
or representative is authorized to assume for the Company any liability other than expressed herein in
connection with the sale of this product. Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential damage, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
The information in this manual was accurate at the time of printing. Changes in features, function, appearance,
or other attributes may occur at any time. Zorg North America is not responsible for errors or omissions in this
manual and makes every attempt to stay current.
10/2020 REV 1 All Rights Reserved Zorg North America LLC.