Zxtech GF-L300PRO User manual
Package Contents ..................................................... 1
At a Glance................................................................ 2
Setting Up Your Floodlight Camera ........................... 4
Using Your Floodlight Camera.................................. 14
Specifications ........................................................... 23
FAQs ........................................................................ 25
Safety and Warranty ................................................ 26
Contents
①Floodlight Camera x 1
②Wire Nuts x 3
③Mounting Bracket x 1
④Waterproof Rubber Gasket x 1
⑤ Screws x 4
⑥Plastic Wall Anchors x 4 ⑦Waterproof Rubber Cap x 6
⑧Hook x 1
⑨Power Cable x 1
⑩User Manual x 1
Package Contents
Please note:
The power cable included in the package is for you to test
the product and get familiar with the functions of the
product before installation.
1
1 2 3 4
5 6
9 10
7 8
GF-L300PRO
Floodlight Camera
User Manual
Thankyou for purchasing our products. This manual addresses
thesafety guidelines, warranty and operating instructions.
Pleasereview this manual thoroughly before operating your
device.
At a Glance
2
Floodlight
PIR Sensor
Infrared Light
Light Sensor (Night Vision Mode)
Lens
Camera
3
Reset Button
Micro SD Card Slot
Micro SD Card Slot Cover
Camera Lock Collar
Base
Floodlight Adjustment
Knob
Setting Up Your Floodlight Camera
Before installation, please check the location where
you want to install the floodlight. The installation
height will influence the motion sensor’s performance
and the viewing angle of the camera.
When the motion detector is installed at a distance of 3
meters (9 feet) from the ground, and an angle of 30
degrees to the ground, it can detect human-sized objects at
up to 8 meters (26 feet).
9 feet
(3 Meters)
4
Parallel to groud
30°
26 feet (8 Meters)
Installation Guide
Please note:
● If you are not sure about how to correctly assemble this
device, consult with a licensed electrician. The wiring
transition shall be strictly in compliance with the local
regulations, rules and national electrical codes.
● Do not connect it to a dimmer switch or timer.
● Do not install it near combustible or flammable surfaces.
● Connect it to a power source (AC 110V to 240V).
● Install it in a place where it can be protected from heavy
rain, heat, and humidity for long service life.
Step 1: Turn off the power to the floodlight at the fuse box
OFF
OFF
Please note:
If you don’t know where your breaker is or how to turn off
the power of the floodlight circuit, consult with a licensed
electrician. For added safety we recommend an AC / DC
Voltage Tester (not included) to ensure the power is off at
the floodlight circuit.
6
Step 2: Remove the mounting bracket
1) Undo the screws with a screwdriver by turning
counterclockwise.
2) Remove the mounting bracket.
Step 3: Install the waterproof rubber gasket on the
mounting bracket
Align the four corners of the gasket with the four corners of
the mounting bracket and press these four corners to fix the
gasket on the bracket.
7
1
2
Step 4: Mark the mounting location
Use a pen to mark the screw holes after determining the
mounting location. We recommend you use a level to make
sure alignment to ground is correct.
Step 5: Select a proper place for drilling
1) Drill a hole in the mounting place that does not influence
plumbing, electrical cables or other building services.
2) Secure the plastic wall anchors into the hole with a
hammer.
8
1 2
Step 6: Fix the mounting bracket on the mounting area
1) Push all the wires through the large opening of the
bracket carefully.
2) Tighten the screws to fix the bracket on the mounting
area. Pay attention to the horizontal position on the top.
White (Neutral) Black (Hot)
White (Neutral)
Black (Hot)
9
Green (Ground)
Green (Ground)
Step 7: Connect the power wire
1) Connect the ground wire coming out of your junction box
to the yellow wire (ground) with tag.
2) Use a wire nut (included) to connect the white wire
(neutral) to the neutral wire coming out of your junction
box.
3) Connect the black wire (hot) to the hot wire coming out of
your junction box using another wire nut.
Please note:
If you are not clear about the neutral or hot wires coming
out of the junction box, consult with a licensed electrician.
10
White (Neutral)
Black (Hot)
Green (Ground)
Step 8: Install the floodlight camera onto the bracket
3) Align the mounting posts with the holes on the floodlight
camera and press them together.
11
4) Secure the floodlight by screwing the screws clockwise.
Step 9: Put the waterproof rubber cap on the screw hole
12
Step 10: Adjust the angle of the floodlight and camera
Loosen or tighten the screw to further adjust the angle of
the floodlight and the camera. After adjusting the angle of
the camera and floodlight, put the waterproof rubber cap on
the screw hole.
Please note:
Do not remove the floodlight part or the camera part from
the ball socket on the base. Failure to do this may result in
product being damaged.
13
Step 11: Turn on the power to the floodlight at the fuse box
OFF
ON
ON
Using Your Floodlight Camera
Please prepare the following stuff before using this
floodlight camera.
A smartphone or tablet using IOS 12.0 / Android 6.0 or
higher (A Mac or Windows PC will not work with this
product).
Preparation
iPad iPhoneAndroid phone
14
A Wi-Fi router (2.4GHz)
2.4G Wi-Fi
The Green LED Indicator Status
Wi-Fi is disconnected
Power On
System State
The Green LED indicator turns on, and
you can hear a voice prompt three times
after about 40 seconds.
The Green LED indicator flashes slowly.
The Green LED indicator flashes fast.
The Green LED indicator goes out.Power off / Wi-Fi is connected
Wi-Fi is connecting
Indicator Activity
15
Installing and Taking Out the Micro SD Card
Please note:
● To ensure the stable video recording of the Micro SD
card, we recommend that you use a Micro SD card (not
included) that is Class 10 or above.
● To make sure the device works normally, please format
the Micro SD card before using it.
Installing the Micro SD Card:
Insert the Micro SD card properly into the slot as below.Wrong
Correct
Taking out the Micro SD card:
Push in the card gently and it will pop outward. The card is
then released from the slot and ready to be removed when
you hear a clicking sound.
Download the iObsurv app from Apple Store / Google Play.
Install iObsurv app on your phone
16
Before adding a camera to the app, please check the
following points:
● Turn on the DHCP of the router. Your MAC address
should be off. DHCP allows the floodlight to automatically
connect to the internet.
● Distance between the router and the camera should be
within 3 meters (9 feet) during configuration.
● Do not use Chinese or special symbols such as %, $, #,
@, *, etc to name the Wi-Fi or set its password. The
name and password of the Wi-Fi can not be blank.
● Make sure your smartphone is connected to the Wi-Fi
router before configuration.
Add a camera to the app
1) Open the app. Tap the " + " icon in the upper right corner,
and select " First Add ".
AT&T 11:57 AM
My Device
AT&T 11:57 AM
My Device
First Add
Manual Add
17
2) Name the camera and scan the camera’s UID (the QR
code on the bottom of the camera, or the tag in the
package).
Side
Customize...
AT&T 11:57 AM
Device Name
Front Door
BackYard
What would you like to name
the device?
Side
How to find the camera ID?
Cannot scan QR code?
AT&T 11:57 AM
Scan the QR code on the back housing.
Scan QR Code Light
Floodlight Cam
User: admin Password:admin
7LWKUK5V3B9H7GU3XXXX
18
Table of contents
