ZyXEL Communications AG-225H User manual

AG-225H
802.11a/b/g/pre-n Wi-Fi Finder & USB Adapter
Quick Start Guide
(For Windows XP/2000, Vista, Mac OS X*)
Version 1.3
December 2006

ZyXEL AG-225H Quick Start Guide
Important Note
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
1

ZyXEL AG-225H Quick Start Guide
Wi-Fi Finder Mode
1. User Interface
NEXT Button
Scroll down to the
next network entry.
SEEK Button
Search network
(Site Survey).
Power OFF Switch
Switch left to power
off the Wi-Fi Finder.
LCM Description
(See next page) Power ON Switch
Switch right to power
on the Wi-Fi Finder.
2

ZyXEL AG-225H Quick Start Guide
2. LCM Description
Security Information
Displays when WEP security is
enabled.
Displays when WPA or WPA2
security is enabled.
Displays when Wireless security is
disabled (no security).
Displays when n-mode WEP,
WPA, or WPA2 security is enable.
Entr
y
Display the current
entry of the detected
Access Points. Users
can detect up to 15
networks at one time.
Channel
Display the radio
channel of the
detected network.
Detect Mode
Display up to 15 detected networks
in the order of the signal strength.
Display the detected networks
without any security setting (free
hot spot).
Display the dedicated network you
choose to use.
SSID
The SSID identifies the Service Set
to the network users detect. When
the length of SSID is longer than 12
characters, it will be scrolled
horizontally.
Battery Status
Display Low Battery
Display Full Battery
Display Battery is charging
Signal
This displays the wireless standard
and signal strength of the selected
network.
802.11a mode at 5 GHz band
802.11b mode at 2.4 GHz band
802.11g mode at 2.4 GHz band
802.11n (pre-n) mode at 2.4 GHz
band
3

ZyXEL AG-225H Quick Start Guide
3. Basic Operation
1. Power on ZyXEL AG-225H.
2. The ZyXEL AG-225H will automatically detect the available wireless
networks in 6~7 seconds.
3. The site survey information will be
displayed on the LCM including the SSID,
channel, signal strength, wireless network
protocol (IEEE802.11a/b/g/pre-n), and the
type of wireless security/encryption (WEP
or WPA)
4. Push NEXT button to see more Access Points you have detected.
For Advanced Features of the AG-225H, there are totally 3 modes to choose:
Mode mode is set by default for most users to detect the Wi-Fi
networks.
Mode
(Free Mode) Hold SEEK button for 1 second to switch to mode.
In mode, push SEEK button to detect the free hot spots or
available WLAN that you can connect to the Access Point
without any security setting.
4

ZyXEL AG-225H Quick Start Guide
Mode When you need to connect the specific Aceess Point and lock
on it, push NEXT button to select the desired Aceess Point.
To dedicate tracking a certain AP, hold “SEEK” button to swith
to mode.
Then push SEEK button once again to periodically do the site
survey automatically in mode. By doing so, the modes can
be changed from mode to mode.
When ZyXEL AG-225H Wi-Fi Finder is not used for 1~2 minutes, the device will
enter into the power saving mode untill you push the SEEK button again for
searching the Access Points.
Charging
When low power icon appears , recharge the AG-225H
with your USB port on your laptop or desktop PC.
The LCM will display when the device is charging and
display when the device finishs charging.
)To save power, switch off the AG-225H when not using Wi-Fi
Finder function.
5

ZyXEL AG-225H Quick Start Guide
4. Button Display
The following table describes the Buttons on the ZyXEL AG-225H when using the Wi-
Fi Finder function.
BUTTON DESCRIPTION
SEEK
Push SEEK button to detect wireless networks in the area.
NEXT
Push NEXT button to see the detected wireless networks.
Switch right to power ON the ZyXEL AG-225H Wi-Fi Finder mode.
OFF/ON
Switch left to power OFF the ZyXEL AG-225H Wi-Fi Finder mode.
6

ZyXEL AG-225H Quick Start Guide
5. LED Display
The following table describes the LEDs on the AG-225H when using Wi-Fi Finder
Mode.
LED COLOR STATUS DESCRIPTION
On The AG-225H is powered on.
Green Off The AG-225H is either powered off or entering into
Power Saving Mode.
On The AG-225H is detecting available wireless networks
Green Off The AG-225H is not actively detecting wireless
networks.
The following table describes the LEDs on the AG-225H when using Adapter Mode.
LED COLOR STATUS DESCRIPTION
On The AG-225H is powered.
Green Off The AG-225H is powered off.
On The AG-225H is connected with an AP/Router.
Blinking The AG-225H is receiving or sending data.
Green
Off The AG-225H is not receiving or sending data.
7

ZyXEL AG-225H Quick Start Guide
Windows XP/2000 Installation
1. Installation Requirements
Before installation, make sure you have the following requirements.
•Pentium II 300MHz or above
•A minimum of 20 MB available hard disk space
•A minimum of 64 MB RAM
•A CD-ROM drive
•An available USB port (for best performance USB2.0 is required)
•Windows XP or Windows 2000 Operating Systems
2. Install the Software
The installation procedures are similar for all supported Windows versions. Windows
XP screen shots are shown unless otherwise specified.
)Install the ZyXEL Utility before you insert ZyXEL AG-225H.
1. Insert the support CD into the CD-ROM drive on your computer.
8

ZyXEL AG-225H Quick Start Guide
2. Click Setup to install the ZyXEL
Utility and driver.
If this screen does not display,
locate and double-click
autorun.exe on the support CD.
3. When the Welcome screen
displays, click Next.
9