3D-Inc TPD-HD330NRW Installation instructions

IR Speed PTZ Camera
INSTALLATION / OPERATING MANUAL
- Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
- The design and specifications are subject to be changed without prior notice to improve
product’s quality.

02
TABLE OF CONTENTS
3p.
4p.
4p.
5p.
6p.
7p.
9p.
28p.
37p.
37p.
37p.
38p.
39p.
42p.
1. PRECAUTIONS
1. 1 Important Safety Instruction ...................................................................................
2. GETTING STARTED
2. 1 Unpacking ..............................................................................................................
2. 2 Part name ...............................................................................................................
2. 3 DIP Switch Setting .................................................................................................
2. 4 Cable Connection ...................................................................................................
3. INSTALLATION
3. 1 Installation .............................................................................................................
4. ON-SCREEN DISPLAY PROGRAM MENU
4. 1 Motion Setting .......................................................................................................
4. 2 Dome Setting .........................................................................................................
4. 3 Clear Setting ..........................................................................................................
4. 4 PTZ Reset ..............................................................................................................
4. 5 Other Quick Opercating Guide .................................................................................
5. SPECIFICATION
5. 1 Mechanism Specification .......................................................................................
6. DIMENSION
6. 1 DIMENSION ..........................................................................................................
7. CONFIGURATION
7. 1 Connecting to Keyboard with DVR ..........................................................................

03
1. 1 Important Safety Instruction
• Read these instructions.
• Pay attention on all the warnings.
• Follow all instructions.
• Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
• Do not dissemble or insert foreign objects.
• Do not install near any heat sources such as radiation, beat registers, stoves, or other apparatus.
(Including amplifiers) that produce heat.
• Do not aim the camera at the sun or any other strong light source.
• Do not install the camera in intermittent lighting environments.
• Only use attachments/accessories specified by the manufacturer.
• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
• Installation should be done only by qualified personnel and conform to all local codes.
• Installation should be done in a place strong enough to hold it.
• Use only installation methods and materials capable of supporting four times the maximum specified load.
• It is designed for indoor use only and it must not be installed where exposed to rain and moisture
without additional outdoor housing and bracket.
• To prevent damage from water leakage when installing a mount outdoors on a roof or wall,
apply sealant around the bolt holes between the mount and mounting surface.
• These instructions are for use by qualified service personnel only. To reduce the risk of electric shock
do not perform any servicing other that contained in the operating instructions unless you are qualified
to do so.
• Only use replacement parts recommended by manufacturer. ad these instructions.
1. PRECAUTIONS

04
2. 1 Unpacking
The following parts are supplied with the outdoor speed PTZ system.
2. GETTING STARTED
<Figure 1. package Components>
2. 2 Part name
Front Back Bottom
Safety loop
ID setting
Commnucation
setting
2
3
1
Analogue video cable
Manual
Ceiling bracket
Wall bracket
SCREW(M4*8 SUS)
Screw
Tape seal
Body
Mount joint
Mount
Ceiling bracket
Pipe socket
SCREW
(SET ANCHOR 1/4")
Screw Power adaptor(Option)
<Wall type> <Ceiling type>
Mount Bolt
Wall bracket
Plate rubber

05
2. 3 DIP Switch Setting
Before start up the camera, set the protocol and camera address and termination set with dip-switches
and click-switches as shown in the below diagram.
1.Set the camera address (ID)
2. Protocol, Baudrate, Camera setting
3.Set the termination On/Off
Address switch
Open the top cover of the product to set camera address.
* ID setting is 1~255 available
S1 S3 S4
S1 : 1-digit number of address
S3 : 10-digit number of address
S4 : 100-digit number of address
Ex) S4 = 1
S3 = 2
S1 = 8
The ID number is 128.
12345678 9101112
ON DIP
123
OFF OFF OFF
OFF OFF ON
OFF ON OFF
OFF ON ON
ON OFF OFF
ON OFF ON
ON ON OFF
ON ON ON
PELCO-D
PELCO-P
WTX
EZP
NC
NC
NC
NC
PROTOCOL 456
OFF OFF OFF
OFF OFF ON
OFF ON OFF
OFF ON ON
ON OFF OFF
ON OFF ON
ON ON OFF
ON ON ON
2400
4800
9600
19200
38400
57600
115200
NC
BAUDRATE
7
OFF
ON RS-422 RS-485
RSMODE 9
OFF
ON OFF ON
RS LOOP 11
OFF
ON IP OFF IP ON
IP SELECT
8
OFF
ON NTSC PAL
NTSC/PAL 10
OFF
ON NC NC
NC 12
OFF
ON OFF
PROGRAM MODE
BOOTO
The device which is connected at the end of the line must have the
cable communication terminated. Without proper termination,
there is potential for control signal errors.
The product have the cable communication terminated by setting
the appropriate dip switch.
9
ON : Terminated
OFF : Not terminated

06
2. 4 Cable connection
2. 4. 2 RS-485/RS-422 Connection
2. 4. 1 Power/Data communication cable connection
RS-422/485 connection
The PTZ can be remotely controlled by an external device or control system, such as a control
keyboard or DVR, using RS-485 half-duplex, RS-422 duplex or simplex serial communication signals.
Connect marked TRx+, TRx- to Tx+ and Tx- of the RS-485 control system.
If control system is RS-422, connect Tx+,Tx- of controller to Rx+ and Rx- of the PTZ Camera series.
And also connect the Tx+, Tx- to Rx+, Rx- of the control device respectively. Total length
of the cable for communication should not exceed 1.2Km.
2. 4. 3 HD-SDI Output connection
Connect the HD-SDI out (BNC) connector to the monitor or video input of DVR. Video cable and
RS-485/422 communication cable are not provided in this product's package.
Do not connect the AC24V power terminal to
the communication terminal.
- Power Terminal: 2PIN
- Com Terminal: 4PIN
Caution
TRx-
TRx+
Tx-
Tx+
HD-SDI POWER AC 24V
Tx + / Tx -
CVBS
FG
AC24
AC24
NETWORK
Coaxial cable
AUX
ALARM INPUT(I/O 1)
ALARM INPUT(I/O 2)
21
43
65
87
10 9
GND SPK
GND MIC
GND DIN
DOB DOA
GND N.C
1
2
3
ALM5
ALM6
GND
4
5
6
ALM7
ALM8
R2-NC
7
8
R2-NO
R2-COM
1
2
3
ALM1
ALM2
GND
4
5
6
ALM3
ALM4
7
8
R1-NC
R1-NO
R1-COM
1
1
2
2
3
3

07
3.Installation
- The following steps of installation and connection work should be done by qualified service personnel
or system installers and should conform to all local codes.
- Be sure to switch the camera off before installation is completed.
- Do not install the camera near the air outlet of an air conditioner.
- Before installation, set the system with Dip switch on the back side of the mechanism part, and
assemble the mechanism and housing according to the below instruction
3. 1 Installation
Set the mount to the wall bracket
by trun it to clockwise.
Push the knob of mount and pull down.
Connect the cable. (See the page6)
To insert or remove the SD card, open the protective cap
and put up the slot cover of SD card.
Cover the protective cap after insert the SD card to prevent
foreign substance damage.
Set the mount to the ceiling bracket by trun it to clockwise.
Knob
Knob
Pipe Socket
Ceiling Pipe
* Fix the socket into the ceiling pipe when install the ceiling
bracket. The socket is included in the accessory package.
Attach
Attach the provided wall bracket rubber
to a wall bracket as shown in the below picture.

08
After connecting the cable, set the mount in the proper position and fix the 2 screws (M4*8)
1. Connect the safety loop on the body and mount back side.
2. Align the arrow mark in the body and mount.
3. Fix the body by turn it to clockwise.
* Please check the direction of connector in the camera body and mount.
CLOSE
(Turn the body to clockwise)
OPEN
safety loop
Front
Front
Fix the provided mount screws
to the PTZ camera tightly.
※Fix the bolt tighten not to make a room
between combinatorial parts to avoid
any water-leakage from outside.

09
4. ON-SCREEN DISPLAY PROGRAM MENU
4. 1 Motion Setting
The initialize screen is shown up to check address, version,
protocol and video when the power on.
MAIN MENU
< NEAR / RIGHT ▷ MOTION >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
EXIT
The preset function is that the camera memorizes
positions of the pan/tilt and zoom. This function is
a representative function of the PTZ camera which
can find memorized preset positions just by selecting
the preset No. A Maximum of 255 Preset positions
are toured in order.
4. 1. 1 Preset
Preset Quick Operating Guide
Set Preset : 1~255 +
Go to Preset : 1~255 +
PRESET
PRESET
INITIALIZE
PTZID
FIRMWARE
V-FORMAT
CVBS
PROTOCOL
BUADRATE
CAMERA
>>PAN OFFSET. . . . . PASS
>>TILT OFFSET. . . . . PASS
NORMAL SETTING . . . . . . WAIT
: 001
: X.XX
: 1080p30
: NTSC
: PELCO D V1.0
: 2400 ,N.1
: MMC
MOTION MENU
< NEAR / RIGHT
ઔ
PRESET >
PRESET
ઔ
GROUP
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
3sec.
୔You can not go into the menu in the IP mode.
୔After label setting, set the motion function.

10
(1) Select the Preset number
P01 : Defined Preset number / 01 : Undefined Preset number
Move : Select : NEAR
PRESET MENU
< NEAR / RIGHT
ઔ
PRESET NO >
PRESET NO : 01 UNDEFINE
LABEL :
POSITION : XXX . X, XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
<<FIRST LABEL SELECT>>
PRESET MENU
PRESET SELECT : 001
<EXIT
ઔ
FOCUS NEAR >
<SEL
ઔ
NEAR /MOVE
ઔ
JOYSTICK>
P001
006
011
016
021
026
031
036
041
P003
008
013
018
023
028
033
038
043
P002
007
012
017
022
027
032
037
042
P005
010
015
020
025
030
035
040
045
P004
009
014
019
024
029
034
039
044
PRESET MENU
< NEAR / RIGHT
ઔ
LABEL >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX . X, XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET MENU
< NEAR / RIGHT
ઔ
POSITION >
PRESET NO : 01 DEFINE
LABEL :
POSITION : XXX .X , XXX. X
FOCUS : AUTO
SAVE CLR BACK EXIT
PRESET POSITION
(3) Define the Preset position
£Select the Position menu
or
NEAR
¤Move and set the position ¥Set & Back
NEAR
PRESET LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : PRESET 01
(2) Set the Preset Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Preset.
After the label is set, push the NEAR button to exit.
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
POSITION : 000. 0 , 000. 0
<EXIT FOCUS NEAR >

11
PRESET MENU
<< NEAR / RIGHT
ઔ
FOCUS >
PRESET NO : 01 DEFINE
LABEL :
POSITION : 000. 0 ,000. 0
FOCUS : AUTO
SAVE CLR BACK EXIT
(4) Select the focus mode for Preset
On focus menu, there are 3 modes : Auto, Manual, Onepush.
Focus will be adjusted once after preset moving.
£Select the Focus menu
or
NEAR
¤Move and set the Focus Menu
PRESET MENU
< NEAR
ઔ
DATA SAVE >
PRESET NO : 01 DEFINE
LABEL :
POSITION : 000. 0 ,000. 0
FOCUS : AUTO
SAVE CLR BACK EXIT
(5) “Save” above setting Pattern data to the memory.
(6) “CLR” means above setting Pattern data will not be
saved and be cleared.
(7) “BACK” means it goes back to the previous
menu :Motion.
(8) “EXIT” means it goes out of MENU.

12
MAIN MENU
< NEAR / RIGHT ▷ PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
BACK EXIT
The Tour function consists of several presets run by turn. It is also adjusts the moving speed
(0~63 step) and dwell time (1~99secs). Maximum of 8 Tour functions are toured in order.
4. 1. 2 Tour
Tour Quick Operating Guide
( 1 Tour can be set for 15 presets. )
୔
MOTION MENU
< NEAR / RIGHT
ઔ
GROUP >
PRESET
ઔ
GROUP ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
Set Tour : 71~78 + 3sec.
Go to Tour : 71~78 +
PRESET
Set Tour : 1~8 + 3sec.
TOUR
PRESET
Go to Tour : 1~8 + TOUR
TOUR SELECT
< SEL
ઔ
NEAR / MOVE
ઔ
JOYSTICK >
01 02 03 04 05 06
07 08
(1) Select the Tour number
T01 : Defined Tour number / 01 : Undefined Tour number
Move : Select : NEAR
TOUR MENU
< NEAR / RIGHT
ઔ
TOUR NO >
TOUR NO : 01 UNDEFINE
LABEL :
TOUR EDIT :
SAVE CLR BACK EXIT
<<FIRST LABEL SELECT>>

13
TOUR MENU
NEAR / RIGHT ▷ TOUR EDIT >
TOUR NO : 01 DEFINE
LABEL : TOUR 01
TOUR EDIT :
SAVE CLR BACK EXIT
(3) Define the Preset position
£Move to the set-up window
or
NEAR
②Move and Delete ③Set & Back
NEAR
(2) Set the Tour Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Tour.
After the label is set, push the NEAR button to exit.
TOUR SELECT 1
001 002 003 004 005 006
007 008 009 010 011 012
013 014 015 016 017 018
019 020 021 022 023 024
025 026 027 028 029 030
031 032 033 034 035 036
037 038 039 040 041 042
043 044 045 046 047 048
049 050 051 052 053 054
<SEL
ઔ
NEAR /MOVE & JOYSTICK>
TOUR MENU
< NEAR / RIGHT
ઔ
LABEL >
TOUR NO : 01 DEFINE
LABEL :
TOUR EDIT :
SAVE CLR BACK EXIT
TOUR MENU
< NEAR
ઔ
DATA SAVE >
TOUR NO : 01 DEFINE
LABEL : TOUR 01
TOUR EDIT :
SAVE CLR BACK EXIT
(4) “Save” above setting Pattern data to the memory.
(5) “CLR” means above setting Pattern data will not be
saved and be cleared.
(6) “BACK” means it goes back to the previous
menu :Motion.
(7) “EXIT” means it goes out of MENU.
TOUR EDIT (02)
NO PRESET SPEED DWELL
01 <XXX> XX XX
02 ඓGXXX XX XX
03 ඓGXXX XX XX
04 ඓGXXX XX XX
05 ඓGXXX XX XX
06 ඓGXXX XX XX
07 ඓGXXX XX XX
08 ඓGXXX XX XX
< SEL & NEAR PRESET & LEFT >
< SEL & NEAR DELETE & WIDE >
TOUR LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : TOUR 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
,WIDE

14
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
GROUP >
PRESET
ઔ
GROUP ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
Set Group : 101~106+
Go to Group : 101~106+
PRESET
PRESET
Group Quick Operating Guide
3sec.
(1) Select the Group number
G01 : Defined Group number / 01 : Undefined Group number
Set from 1to 6 groups.
Move : Select : NEAR
4. 2. 3 Group
GROUP : You can make Max. 6 groups and call the saved tour by turn.
GROUP SELECT
< SEL ▷ NEAR / MOVE
ઔ
JOYSTICK >
G01 02 03 04 05 06
GROUP NO : 01 UNDEFINE
LABEL :
GROUP EDIT
ઔ
GROUP MENU
< NEAR / RIGHT
ઔ
GROUP NO >
SAVE CLR BACK EXIT
<<FIRST LABEL SELECT>>

15
(2) Set the Group Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Group.
After the label is set, push the NEAR button to exit.
(3) GROUP EDIT
£Move to the set-up window
or
NEAR
(4) “Save” above setting Pattern data to the memory.
(5) “CLR” means above setting Pattern data will not be
saved and be cleared.
(6) “BACK” means it goes back to the previous
menu :Motion.
(7) “EXIT” means it goes out of MENU.
- GROUP EDIT : Set the tour from 1 to 6 of group.
②Move and Delete ③Set & Back
NEAR
,WIDE
GROUP LABEL EDIT
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL :
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
GROUP MENU
< NEAR / RIGHT
ઔ
LABEL>
GROUP NO : 01
LABEL :
GROUP EDIT
ઔ
SAVE CLR BACK EXIT
GROUP EDIT (01)
NO TOUR
01 <001>
02 002
03 XXX
04 XXX
05 XXX
06 XXX
< SEL & NEAR PRESET & LEFT >
< SEL & NEAR DELETE & WIDE >
GROUP MENU
< NEAR
ઔ
DATA SAVE >
GROUP NO : 01
LABEL :
GROUP EDIT
ઔ
SAVE CLR BACK EXIT
GROUP MENU
< NEAR / RIGHT
ઔ
GROUP EDIT>
GROUP NO : 01
LABEL :
GROUP EDIT ඖ
SAVE CLR BACK EXIT

16
SCAN SELECT
< SEL
ઔ
NEAR / MOVE

JOYSTICK >
01 02 03 04 05 06
07 08
(1) Select the Scan number
S01 : Defined Scan number / 01 : Undefined Scan number
Move : Select : NEAR
The Scan function means that the camera keeps panning between two programmed pan positions.
It is also adjusts the moving speed(1~63 step). Maximum 8 Scan functions are toured in order.
4. 1. 4 Scan
Scan Quick Operating Guide
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
SCAN >
PRESET
ઔ
GROUP
ઔ
TOUR
ઔ
SCAN ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
Set Scan : 81~88 +
Go to Scan : 81~88 +
PRESET
Set Scan : 1~8 + Scan
PRESET
Go to Scan : 1~8 + Scan
3sec.
3sec.
SCAN MENU
< NEAR / RIGHT
ઔ
SCAN NO >
SCAN NO : 01 UNDEFINE
LABEL :
START POS : XXX . X, XXX . X
END POS : XXX . X, ---
SPEED : XX
DWELL : XX
FOCUS : NONE
SAVE CLR BACK EXIT
<<FIRST LABEL SELECT>>

17
SCAN MENU
< NEAR / RIGHT
ઔ
LABEL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : XXX . X, XXX . X
END POS : XXX . X, ---
SPEED : XX
DWELL : XX
FOCUS : NONE
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
START POS >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
END POS >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN STRAT POSITION
< EXIT
ઔ
FOCUS NEAR >
POSITION : 000.0, 000.0
(3) Define the Start pan position
£Select Start Pos menu
or
NEAR
¤Move and set the position ¥Go back
NEAR
(2) Set the Scan Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
(4) Define the End pan position
£Select End Pos menu
or
NEAR
¤Move and set the position ¥Go back
NEAR
POSITION : 000.0, 000.0
SCAN END POSITION
< EXIT
ઔ
FOCUS NEAR >
It’s available to set the desired label, displayed on the executing screen of Scan.
After the label is set, push NEAR button to go out.
SCAN LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : SCAN 01
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >
୔Save the zoom, Tilt and position.

18
(8) Save above Scan data setting to the memory.
(9) “CLR” means above setting Scan data will not be
saved and be cleared.
(10) “BACK” means it goes back to the previous
menu :Motion.
(11) “EXIT” means it goes out to MENU
(7) Set the Focus
(5) Set the Scan speed
Increase : or
Decrease : or
TELE
JOYSTICK
WIDE
JOYSTICK
SCAN MENU
< NEAR / RIGHT
ઔ
MOVE SPEED >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
DWELL >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR / RIGHT
ઔ
FOCUS MODE >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
SCAN MENU
< NEAR
ઔ
DATA SAVE >
SCAN NO : 01 DEFINE
LABEL : SCAN 01
START POS : 000 . 0 , 000 . 0
END POS : 000 . 0 , ---
SPEED : 60
DWELL : 02
FOCUS : AUTO
SAVE CLR BACK EXIT
It adjusts the moving speed from 1~63 steps.
Focus can be set Auto or Manual.
(6) Set the Dwell Time
Increase : or
Decrease : or
TELE
JOYSTICK
WIDE
JOYSTICK
Dwell time means the time that the camera stay at
the start & end pan positions.
It’s adjustable from 00~59seconds.

19
PATTERN SELECT
< SEL
ઔ
NEAR / MOVE & JOYSTICK >
01 02 03 04
(1) Select the Pattern number
PAT01 : Defined Pattern number / 01 : Undefined Pattern number
Move : Select : NEAR
The Pattern function memorizes User’s random moving path and zoom ratio. Total recording time
limit is 90secs and maximum 4 Pattern functions are toured in order.
4. 1. 5 Pattern
MAIN MENU
< NEAR / RIGHT
ઔ
PRESET >
MOTION
ઔ
DOME
ઔ
CAMERA
ઔ
CLEAR
ઔ
PTZ RESET
BACK EXIT
MOTION MENU
< NEAR / RIGHT
ઔ
PATTERN >
PRESET
ઔ
GROUP
ઔ
TOUR
ઔ
SCAN
ઔ
PATTERN
ઔ
ALARM
ઔ
AREA
ઔ
PRIVACY
ઔ
BACK EXIT
Set Pattern : 91~94 +
Go to Pattern : 91~94 +
PRESET
Set Pattern : 1~4 + Pattern
PRESET
Go to Pattern : 1~4 + Pattern
Pattern Quick Operating Guide
3sec.
3sec.
PATTERN MENU
< NEAR / RIGHT
ઔ
PATTERN NO >
PATTERN NO : 01 UNDEFINE
LABEL :
RECORD :
PLAY :
SAVE CLR EXIT
<<FIRST LABEL SELECT>>

20
PATTERN MENU
< NEAR / RIGHT
ઔ
LABEL >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
ઔ
PLAY
ઔ
SAVE CLR EXIT
PATTERN MENU
< NEAR / RIGHT
ઔ
RECORD >
PATTERN NO : 01 DEFINE
LABEL :
RECORD ඖ
PLAY
ઔ
SAVE CLR EXIT
PATTERN MENU
< NEAR / RIGHT
ઔ
PLAY >
PATTERN NO : 01 DEFINE
LABEL :
RECORD
ઔ
<08SEC>
PLAY
ઔ
SAVE CLR EXIT
(4) Play back the recorded Pattern data
(3) Record and Save the User’s random Pattern data
£Select the “Record” Menu
or
NEAR
¤Move and record the pattern ¥Set & Back
NEAR
000.0, 000.0
EXIT
ઔ
NEAR 06/60
PATTERN RECORD
(2) Set the Pattern Label
Move : Select : or or Delete : or
TELE
JOYSTICK
WIDE
JOYSTICK
It’s available to set the desired label, displayed on the executing screen of Pattern.
After the label set, push NEAR button to go out.
PATTERN LABEL EDIT ( 01 )
< DELETE
ઔ
WIDE
< STORE
ઔ
TELE
BACK
ઔ
NEAR >
MOVE
ઔ
JOYSTICK >
LABEL : PATTERN
0 1 2 3 4 5 6 7 8 9 (
) A B C D E F G H I J K
L M N O P Q R S T U V W
X Y Z . / , + - = < >