3Jtech DWR User manual

Ver 1.0.0.0
1
Quick Installation Guide for Dedicated Wifi Router (DWR)
1. DWR packing list :
Before you start installing DWR, please verify that the package contains the following items:
One Set of DWR
1x Power Adapter
RJ-45 Network Cable
Quick Installation Guide and User’s Guide
NOTE: Please notify your sales representative immediately if any items listed above is missing or damaged.
2. Hardware connection settings for DWR
1) Connect XDSL/Cable to the WAN port of your DWR using a RJ-45 cable.
2) Connect PC to LAN port of your DWR using a RJ-45 cable.
3) Connect the power cable to the power connector of your DWR.
4) Please refer to section 3 about WIFI settings to have DWR connect to your desired wireless
devices wirelessly.
3. Software configuration for DWR
Before the setup, please confirm that the LAN port of the DWR has been connected with the PC
via RJ-45 cable.
ySet up the DWR for ADSL / cable modem
1. Connect the WAN port on the DWR to your DSL modem, cable modem or to your
Ethernet Hub if you have the fixed IP.
2. Determine your provider’s IP scheme: fixed IP, DHCP or PPPoE. (Please ask your
Internet Service Provider for the connection details and information.)
3. Type http://192.168.8.1 into IE browser to enter the setup for the DWR.
4. Please input “cameras” as the user name and the password for the DWR.
5. PPPoE ÆSet up the PPPoE account (User Name and Password) on the DWR.

Ver 1.0.0.0
2
6. If your WAN port is using a fixed IP ÆSet up the fixed IP on the DWR.
7. For cable modem users (DHCP), please leave the Internet setup as default.
ySet up the DWR for wireless devices
With our proprietary wifiDHCP technology, the wireless IP camera series such as wifiCAMit,
wifiCAMit_Dome, wifiCAMit_CS…etc. can be plug and play with regards to its WIFI
settings if you use it in conjunction with 3JTech’s Dedicated Wifi Router (DWR). Please
follow the procedures below to set up your wifiCAMit IP camera or other wireless devices
with the DWR. For more details on WIFI settings, please also refer to the DWR user’s
manual.
－ Connecting the wifiCAMit IP camera to the DWR
(Please skip this section if you would like to use other wireless devices.)
1) Connect the power cable to the power jack of DWR.
2) Connect the wifiCAMit to a LAN port of DWR via the RJ-45 cable.
3) Connect the power cable to RJ-22 jack of the wifiCAMit.
4) The LED on the back of the wifiCAMit will flash when the SSID and WEP Key of the
DWR are passed to the wifiCAMit successfully.
5) Remove the power cable of the camera and RJ-45 cable.
6) Switch the button located at the left side of the camera into “Wireless” position.
7) Plug in the power cable of the wifiCAMit.
NOTE: The new SSID and WEP key will be generated after resetting the DWR.
WIRELESS
WIRED

Ver 1.0.0.0
3
－ Connecting other wireless devices to the DWR
(Please skip this section if you would like to use our wireless IP camera series.)
1) Connect the power cable to the power jack of DWR.
2) Connect the wireless device to a LAN port of DWR via the RJ-45 cable.
3) Power on the wireless device.
4) Initiate your Internet Explorer and type http://192.168.8.1 into IE browser. Click OK
button to enter the setup page of DWR after inputting the following username and
password. Username: cameras
Password: cameras
5) Please go to Wireless / Basic Settings by pulling down the function list located at the
left side.
6) In Wireless Basic Settings page, please use the values of WEP Key and SSID fields to
set up your wireless devices. (Note: The wireless devices will get the SSID belonging
to the DWR automatically if the function of broadcast is enabled.).
4. Restore Factory Default Settings
DWR provides the Def. button that will be easy for users to
reset the router to its factory defaults. The button locates in
the bottom of the DWR (See Def. button of the figure at the
right side). Resetting steps are as follows:
(1) Move the cover in the bottom of the router.
(2) Plug in the power cable and wait around 20~30 seconds.
(3) Press the Def. button and keep it pressed around 7
seconds.
(4) The DWR will restart after releasing the Def. button.
Def. BUTTON