3t-components 3t-motors 3t45-20 Manual

www.3t-components.de |WEEE-Reg.-Nr.: DE 77028333

Solar panel SP50

with integrated battery &

Radio receiver

3T-MOTORS Shutter / Awning motors 12V

with mechanical limit switches

Motor type 3T45-20/12V

(Für Wellen ab 60 mm)

Motor type 3T35-13/12V

(Für Wellen ab 40 mm)

Motor type 3T45-50/12V

(Für Rundwellen ab 63 mm)

INTELLIGENT

DRIVES &

CONTROLS

FOR SHUTTERS

AND AWNINGS

INSTALLATION &

OPERATING INSTRUCTIONS

Instructions and notes for installation and operation

Attention:

It is important for the safety of persons

to follow these instructions.

Keep these instructions for future reference.

TABLE OF CONTENTS

3T-MOTORS Shutter motors / Awning motors 12V + Solar Panel SP50

Safety instructions Page 3

Function overview

Function overview 3T45/12V / 3T35/12V Page 4

Function overview Solar panel SP50 Page 5

Programming

Connecting shutter motor to SP50 solar panel Page 6

Pairing transmitter to SP50 solar panel Page 6

Change the direction of rotation of the motor Page 7

Pairing another transmitter Page 7

Delete transmitter Page 7 – 8

Reset to factory settings Page 8

Installation notes Page 9

Installation instructions

Installation roller shutter motor 12V + SP50 Page 10 – 15

•Installation situation Page 10

•1) Prepare power connection Page 10

•2) Select motor bearing Page 10 – 11

•3) Remove shutter shaft Page 12

•4) Prepare motor for installation Page 12

•5) Mount bearings Page 12

•6) Mount motor with shaft unit Page 12 – 13

•7) Mount solar panel SP50 Page 13

•8) Shutter motor wiring Page 13

•9) Setting the end positions Page 14 – 15

•Mounting instructions for motor type 3T35/12V Page 16

Installation awning motor 12V + SP50 Page 17 – 12

•1) Preparation Page 17

•2) Prepare motor for installation Page 17

•3) Mount awning motor Page 17 – 18

•4) Mount solar panel SP50 Page 18

•5) Wiring awningmotor + solar panel Page 18

•6) Setting the end positions Page 19 – 20

Troubleshooting

What to do when ... Page 21

EU Declaration of Conformity Page 22

Hotline

06732 600 0369

CONTACT

3T-Components GmbH & Co. KG

Bahnhofstr. 34

55578 Wallertheim

Email: info@3t-components.de

Tel: +49 (0) 6732-600 03 69

Fax: +49 (0) 6732-600 54 30

Opening hours:

Monday – Friday

8:00 – 17:00

www.3t-components.de

Learn more about us:

All contents of these instructions, in particular texts, photographs and graphics, are protected by

Co. KG. Please ask us if you wish to use the contents of this document. 3T-MOTORS Tubular motors 12V | Table of contents

GENERAL SAFETY INSTRUCTIONS

IMPROPER USE

PROPER USE

•WARNING: Important safety instructions.

Follow all instructions as incorrect installation may result in serious injury.

•WARNING: The drive must be disconnected from the power source during cleaning, maintenance and replacement of parts.

•Danger to life from electric shock when working on electrical equipment.

• The electrical connection, installation and commissioning of the receiver may only be carried out by qualied personnel.

•Before installing the drive, remove all unnecessary cables and disable all devices,

that are not required for operation with power.

•The relevant regulations and guidelines must be followed without fail, to avoid damage to persons and objects.

•Observe safety instructions according to EN 60 335-2-97: The power supply cable of the drives must be laid internally.

•Installation according to DIN 18073: The roller shutter box cover must be easily accessible and removable.

•Installation according to EN 60335: Only switches / pushbuttons / switching devices with a minimum contact opening

of 3 mm may be used, furthermore the up and down direction must be interlocked against each other.

•When installing in damp rooms, observe regulations (VDE 0100, part 701 and 702).

•Please never operate several motors via one switch / pushbutton, unless you are using

cut-off relays or other controls that allow parallel operation.

•Do not use defective devices: Never use defective equipment.

Periodically inspect the equipment for imbalance and signs of wear or damage to cables and suspension springs.

Do not use equipment if repair or touch-up is necessary.

There is a risk of personal injury and property damage due to electric shock or short circuit.

•Retain the instructions for future reference.

•Use tubular motors only for automating shutters.

•Only use original components and original accessories from the manufacturer.

•The mains connection cable of the drives must be laid internally in the empty conduit up to the junction box.

The local electrical regulations must be observed.

•For the electrical connection of the tubular motors, a 230 V / 50 Hz

power connection with fuse must be available at the installation site.

•Inspect the installation frequently for imbalance and signs of wear or damage to cables and springs.

Do not use if repairs or adjustments are required.

3T-MOTORS Tubular motors 12V | Safety instructions

Please read these important safety instructions before commissioning!

Incorrect installation can cause serious personal injury and damage to property.

The warranty claim expires in case of non-observance of this user information with all contained notes and regulations.

In case of non-observance of these instructions, the manufacturer or supplier shall not be liable for any personal injury or property damage incurred.

SAFETY INSTRUCTIONS

This symbol indicates danger due to electrical energy.

Danger to persons and objects may arise if the

associated information is not observed!

This symbol indicates information about general danger.

Non-observance can mean danger to

persons and objects!

This symbol indicates important information that can

ensure safe and proper use of the device.

•Persons are to be instructed with the correct operation of the tubular motor.

•The roller shutter movement must be monitored in order not to endanger persons.

•Do not allow children to play with motor controls.

•Store the handheld transmitter in such a way that unintentional operation is prevented (e.g. by children playing).

•The device can be used by children aged 8 years and above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge, if they have been given supervision and instruction concerning use

of the appliance in a safe way and are aware of the hazards involved.

•Children are not allowed to play with the equipment.

•If the power supply cord of this device is damaged, it must be replaced by the manufacturer or its customer service

or a similarly qualied person to prevent hazards.

APPLICATION

Motorized radio shutters & awnings

SCOPE OF DELIVERY – MOTOR TYPE 3T45/12V

1Motor

2Limit switch adapter

3Shaft adapter

4Connection cable 3 meters

5Adjustment pin

6Universal bearing & cotter pin

7Cover cap bearing (3T45-20/12V)

8Securing bracket

9Manual

FUNCTION OVERVIEW 3T45/12V / 3T35/12V

Motor type

Torque (Nm)

Traction power (kg)

Max. PVC shutter area (m²)

Max. ALU shutter area (m²)

Power (W)

Turn Speed (U/min)

Limit switch capacity (min)

Operating voltage (V AC)

L1 Total motor length (mm)

L2 Installation length (mm)

Connection line (m)

Max. Runtime (min)

Protection class

EAN

3T45-20/12V

4,7

565

541

2,5

IP44

+ SP50: 4260601762394

3T35-13/12V

5,5

595

575

2,5

IP44

+ SP50: 4260601760550

Technical Data

2 31

6 7 8 9

SCOPE OF DELIVERY – MOTOR TYPE 3T35/12V

1Motor

2Limit switch adapter

3Shaft adapter

4Connection cable 3 meters

5Adjustment pin

6Universal bearing & cotter pin

7Clip bearing

8Securing bracket

9Manual

2 31

6 7 8 9

SUITABLE FOR

8-sided Shafts from 60 mm

Ø60 mm

APPLICATION

Motorized radio shutters

SUITABLE FOR

8-sided Shafts from 40 mm

Ø40 mm

Limit switch Limit switch

Optional adapter sets + accessories >Optional accessories tubular motors (Page 22 – 23)

3T45-50/12V

100

Suitable for folding awnings with up to

8 m projection (with 2 folding arms)

142

661

637

2,5

IP44

+ SP50: 4260601760536

3T-MOTORS Tubular motors 12V | Function overview

FUNCTION OVERVIEW SOLAR PANEL SP50

•Solar module with integrated battery and

Radio receiver

•Suitable for 12 V - tubular motors

up to 50 Nm torque

•Up to 20 transmitters of the 3T radio series

can be stored

•Sleep mode with low power consumption

•If the operating voltage drops below 9.5 V

the LED display ashes 5x

Technical Data

Operating voltage / DC

Switching capacity

Operating temperature range

Frequency

Radio receiver range

Dimensions (LxWxH)

Channels

Compatibility

EAN

9,5 V ~ 12,6 V

for 12 V - tubular motors up to 50 Nm torque

-15 °C to +55 °C

433,92 MHz ± 100 KHz

approx. 30 meters indoors / 100 meters outdoors

595x92x32 mm

can store max. 20 transmitter channels

compatible with all 3T radio transmitters

SP50 + 3T45-20/12V: 4260601762394 / SP50 + 3T35-13/12V: 4260601760550

Damage caused by improper use or

or unprofessional installation,

lead directly to loss of warranty.

Before startup

1) Remove cover and charge internal battery via:

2) Micro USB cable 5 V (Micro USB B connector)

Open cover Micro USB port 5 V

Connect micro USB cable

Press program button > LED ashes green > Battery is charging

3) Sunlight

1 2

LED indicator

green light: signal for charging state

red light: signal for programming

Program button

End idle state

Pairing transmitter

Change direction of motor rotation

Factory settings

Charging port

Micro USB 5 V

3T-MOTORS Tubular motors 12V | Function overview

PROGRAMMING

The internal battery must be charged before programming.

Perform programming before mounting the motor and solar module.

One transmitter can control up to 20 solar modules. Receiver stores a maximum of 20 transmitters (channels).

1 x Press button

P2 / Set Up

Pairing of handheld transmitter to

SP50 solar module:

Press and hold program

button for 2 sec.

Programming (pressing the buttons) must be carried out within 10 seconds.

Otherwise the system returns to its original state.

Tubular motor

starts 1 x

Release

programm button

LED indicator

ashes 1 x

LED indicator

ashes 1 x

1 x Press button

P2 / Set Up

1 x press Up-button

Transmitter is paired

Up-button controls

motor forward

1 x press Down-button

Transmitter is paired

Down-button controls

motor forward

LED indicator

ashes 1 x

Tubular motor starts 1 x,

LED indicator ashes 4 x

Tubular motor starts 1 x,

LED indicator ashes 4 x

Connect the shutter motor to the SP50 solar module:

•Slide the rotary lock of the SP50 solar module connection to the rear.

Before connecting the connecting cables, make sure that the markings (arrow) are opposite each other. >g. 1

•Connect solar module SP50 and shutter motor together. >g. 2

•Fix the connection of the cables with the twist lock. Close the twist lock tightly to prevent water from entering. >g. 3

•After programming, disconnect the connection cables again for mounting.

1Connection

SP50

Connection

tubular motor

2 3 Twist lock

Note:

When programming, make sure that the direction of rotation of the motor is correct.

This means that the direction of rotation does not have to be changed after assembly.

3T-MOTORS Tubular motors 12V | Programming

Pairing another handheld

transmitter:

New transmitter

is paired

1 x Press button P2 / Set Up

of the already paired transmitter

1 x Press button P2 / Set Up

of the new transmitter

1 x Press button P2 / Set Up

of the new transmitter

Tubular motor starts 1 x,

LED indicator ashes 1 x

Tubular motor starts 1 x,

LED indicator ashes 5 x

LED indicator

ashes 1 x

Delete handheld transmitter:

1Delete a paired transmitter

Transmitter b

is deleted,

transmitter a

will not be deleted

1 x Press button

P2 / Set Up

1 x Press button

P2 / Set Up

1 x Press button

P2 / Set Up

Tubular motor starts 1 x,

LED indicator ashes 1 x

Tubular motor starts 1 x,

LED indicator ashes 6 x

LED indicator

ashes 1 x

a a b

Change direction of rotation

of radio motor:

Direction of rotation

is changed

Press and hold program

button for 6 sec.

Tubular motor

starts 2 x

Release

programm button

LED indicator

ashes 2 x

3T-MOTORS Tubular motors 12V | Programming

PROGRAMMING

Programming (pressing the buttons) must be carried out within 10 seconds.

Otherwise the system returns to its original state.

Programming (pressing the buttons) must be carried out within 10 seconds.

Otherwise the system returns to its original state.

Programming (pressing the buttons) must be carried out within 10 seconds.

Otherwise the system returns to its original state.

Reset to factory setting:

Reset to

factory setting

Restoring the factory setting will delete all settings and transmitters!

The solar panel then automatically goes into sleep mode. No programming can be carried out in the sleep mode.

To end the sleep mode, press and hold the program key for 2 seconds > the tube motor starts up once and the solar panel switches to pairing mode.

2Delete all paired transmitters

All transmitters

are deleted

1 x Press button

P2 / Set Up

1 x Press

Stop-button

1 x Press button

P2 / Set Up

Tubular motor starts 1 x,

LED indicator ashes 1 x

Tubular motor starts 1 x,

LED indicator ashes 4 x

LED indicator

ashes 1 x

Press and hold program

button for 11 sec.

Tubular motor

starts 3 x

Release

programm button

LED indicator

ashes 3 x

3T-MOTORS Tubular motors 12V | Programming

PROGRAMMING

Programming (pressing the buttons) must be carried out within 10 seconds.

Otherwise the system returns to its original state.

Note:

The following 3T-MOTORS transmitters do not have a P2 / Set Up button:

Radio wall transmitter

WS1

Radio wall transmitter

WS2

Radio wall transmitter

WSE2

Radio timer

WSTF1

Radio timer

WSTF5

Radio mini transmitter

FMSF

Button combination:

Press Up + Stop buttons simultaneously (FMSF / WS1 / WS2 / WSE2).

Press the Set and Mode buttons simultaneously (WSTF1/ WSTF5).

•Do not expose the tubular motor to crushing, impact, falling or contact with any liquids.

Do not punch holes in the entire length of the tube (motor casing) or attach screws to it.

•Please use suitable suspension springs to fasten the roller shutter curtain to the roller shutter shaft.

You will nd suitable suspension springs on page 23 and in our store under mounting accessories.

•Important for motor type 3T35/12V (SW40):

It is essential to use mini suspension springs for motor operation. These special mini springs protrude only approx.

1 mm into the shaft. This allows the shaft to rotate freely. When using commercially available suspension springs

the motor housing is left with grinding marks because the suspension pin protrudes too far into the roller shutter shaft,

which leads to damage and destruction of the motor.

•For steel shafts with a width across ats of 40 mm (SW40), only use shafts with

an external fold. Steel shafts with an internal fold will damage and destroy the motor.

•Grinding marks of any kind on the motor housing will void the warranty.

•The inspection cover of the roller shutter box must be easily accessible and removable.

•The motor is designed for short-time operation (12 min). It has an internal thermal circuit breaker which interrupts

the power supply in the event of overheating, e.g. as a result of continuous operation. The cooling phase is min. 10 min,

the thermal switch resets automatically. Regular operation is only possible after the the motor has cooled down completely.

Mini suspension springs (Page 23)

Before installation, all non-essential electrical wiring must be removed, all mechanisms

that are not necessary for motorized operation must be deactivated.

8-sided shaft SW40

with external fold

Do not use

8-sided shaft SW40

with internal fold!

3T-MOTORS Tubular motors 12V | Installation notes

INSTALLATION NOTES

INSTALLATION SHUTTER MOTOR 12V

Installation situation

1Counter bearing*

2Ball bearing*

3Roller capsule*

4Shutter shaft*

5Suspension spring*

6Shaft adapter

7Tubular motor

8Limit switch adapter

10 Limit switches

10 Engine mount

11 Shutter curtain*

* Accessories; not included

1Prepare power connection:

•The mains connection cable of the drive must be laid internally in the empty conduit up to the junction box.

The local electrical regulations must be observed.

2Select motor bearing:

•Two motor bearings are supplied: Universal bearing and Cover cap bearing (3T45-20/12V) / Clip bearing (3T35/12V).

•Use one of the two motor bearings depending on the installation situation.

1 2 3 4 5 6 7 8 9 10

Please note:

•The motor can be installed on the right-hand side as well as on the left-hand side.

If the direction of rotation is reversed, please exchange the wires for the up and down direction.

•The setting of the end positions is only possible in the installed state (motor in shutter shaft).

•Never place screws in the area of the tube motor, as they will damage the motor.

•Engine damage caused by improper use or unprofessional installation,

lead directly to loss of warranty.

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

Motor type 3T45-20/12V

Installation with universal bearing or cover cap bearing

Installation with universal bearing:

•Push the motor with the square into the opening of the bearing

and secure with cotter pin.

Installation with cover cap bearing:

•Remove screws from metal plate on motor head >g. 2.1

•Remove metal plate >g. 2.2

•Remove motor square spigot >g. 2.3

•Reattach metal plate >g. 2.4

•Slide motor type 3T45-20/12V without square spigot into cover cap

bearing and secure with both securing clips.

Motor type 3T35-13/12V

Installation with universal bearing or clip bearing

Installation with universal bearing:

•Push the motor with the square into the opening of the bearing

and secure with cotter pin.

Installation with clip bearing:

•Remove screws from metal plate on motor head >g. 2.5

•Remove metal plate >g. 2.6

•Remove motor square spigot >g. 2.7

•Reattach metal plate >g. 2.8

•Engage motor type 3T35/12V without square spigot in clip bearing.

2.1 2.2

2.3 2.4

2.62.5

2.82.7

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

Universal bearing Cover cap bearing Universal bearing clip bearing

Cotter pin Cotter pin

Square spigot Square spigot

Securing clips

3Remove shutter shaft:

•Lower the roller shutter.

•Open the cover of the roller shutter box.

•Release the suspension springs from the roller shutter shaft.

•Lift roller shutter shaft incl. ball bearing out of the holder.

4Prepare motor for installation:

•Push limit switch adapter ush against motor head. >g. 4.1 / 4.2

•Secure the shaft adapter with the supplied securing bracket. >g. 4.3 / 4.4

•Push the motor into the roller shutter shaft without using force (never knock it in). The fold of the shaft must lie over the recess in the shaft adapter. >g. 4.5 / 4.6

•Make sure that the roller shutter shaft is ush with the motor head limit switch adapter. >g. 4.7 / 4.8

5Mount bearings:

•Remove old wall bearing on motor side (left or right installation possible).

•Mount motor bearing at this point (2 mounting options: Universal bearing and cover cap bearing (3T45-20/12V) / clip bearing).

•Please mount the bearings so that the limit switches are freely accessible.

•Make sure that the roller shutter motor with the shaft unit sits horizontally in the roller shutter box.

6Mount motor with shaft unit:

•Insert the motor head (with the entire shaft unit) into the motor bearing and secure it with the supplied cotter pin or securing clips (Cover cap bearing).

4.1 4.2 4.3 4.4

4.5 4.6 4.7 4.8

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

Limit switch adapter

Motor head

Securing bracket

Click

Shaft adapter

Roller shutter shaft

Fold

Recess

wrong right

7Mount solar module SP50:

•Mount the solar module to the wall or roof using one of the following options:

8Connection roller shutter motor + solar module SP50:

•Connect cables of shutter motor and solar module SP50 (see description page 6).

•If the drive should run in the opposite direction after installation, the direction of rotation must be changed via the solar panel SP50.

(see programming page 7).

•Insert the wall brackets (1) into the fasteners and secure them

with the screws (2) supplied.

•Fix the fastenings with the supplied grub screws (3) at the desired

position with hexagonal wrench.

•Mount the wall brackets on the wall with the supplied dowels and screws.

•Attach the clip holder (1) to the wall or roof with suitable screws and dowels.

When doing so, take the desired angle into account.

•Snap the solar module into the clip holder.

Mounting with 2 wall brackets: Mounting with clip bearing:

•On the opposite side of the motor, push the roller capsule out of the roller shutter shaft until it ts into the ball bearing inserted in the wall bearing.

•Fix roller capsule to roller shutter shaft with self-tapping screw. Position the screw at a punched hole. This prevents the screw from slipping.

SP50 Rear with wall brackets SP50 Rear with clip bearing

2 23

1 1

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

Roller capsule

Wall bearing +

Ball bearing

9Setting the end positions:

Explanation of the limit switch screws

There are 2 limit switch screws on the motor head. One limit switch screw is responsible for the upper end position, the other for the lower end position.

The end positions can be adjusted by turning the limit switch screws with the adjustment pin.

The arrows with PLUS and MINUS apply to both limit switch screws and show you in which direction you must turn the adjusting pin to switch

off the motor sooner or later. Turning the limit switch screw in the PLUS direction after switching off allows the motor to continue moving step

by step in the corresponding direction. Turning the limit switch screw in the MINUS direction during travel causes the motor to switch off earlier.

For motor type 3T45/12V / power cable to the front, the PLUS and MINUS directions change (see marking on the motor head).

Motor type 3T45/12V / Power cable to rear Motor type 3T35/12V / Power cable to rearMotor type 3T45/12V / Power cable to front

The straight up and down arrows indicate the direction of rotation

of the motor and shaft and thus show you for which end position

the limit switch screw next to it is responsible. Depending on

whether the direction of rotation leads to unrolling or rolling up of

the roller shutter, the limit switch screw is responsible for the lower

or upper end position (unrolling > lower end position, rolling up >

upper end position).

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

Adjustment pin

On motor type 3T35/12V, the limit

switch screws are located on one

side of the motor head only.

Left installation

Limit switch screw white:

Lower end position

Limit switch screw red:

Upper end position

Right installation

Limit switch screw red:

Lower end position

Limit switch screw white:

Upper end position

Power cable to rear

Left installation

Limit switch screw red:

Upper end position

Limit switch screw white:

Lower end position

Right installation

Limit switch screw white:

Upper end position

Limit switch screw red:

Lower end position

Power cable to front

Direction of rotation

Limit switch screw

Direction of rotation

Limit switch screw

Special case: Roller shutter rolls down in front of motor + shaft

If the roller shutter curtain rolls in front of the motor and shaft, the responsibilities of the limit switch screws for the upper and lower end positions are reversed.

See illustration of left-right installation on page 14: upper end position > lower end position / lower end position > upper end position.

Adjustment pin

is required

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

1. Setting the lower end position

•Do not fasten the roller shutter curtain!

Detach all suspension springs from the roller shutter shaft!

•Move the motor + shaft in the downward direction until the lower limit switch-off occurs automatically

and the motor stops.

•Move motor + shaft upwards.

While the motor is moving upwards, turn the adjustment pin on the limit switch screw for the upper limit

position in the MINUS direction (up to 100 turns, depending on the motor type) until the motor switches

off after approx. 4 turns.

This prevents the roller shutter from being pulled out of the guide rails when the upper end position is set.

•Move motor + shaft in downward direction to the lower end position until the motor stops automatically.

•If the shaft has to be turned a little to hook in the suspension springs, use the adjustment pin on the

limit switch screw for the lower end position in the PLUS direction. This causes the motor to turn the shaft

stepwise. The rectangular openings in the shaft for hooking in the suspension springs should point forward

and be easily accessible.

•Hang the roller shutter curtain on the roller shutter shaft using the suspension springs.

2. Setting the upper end position

•Allow the motor + roller shutter to move upwards until the motor stops automatically at the previously set

upper end position.

•To set the upper end position, turn the adjustment pin on the limit switch screw for the upper end position

in the PLUS direction to raise the motor + roller shutter further. The upper end position should be that the

roller shutter stops approx. 3 cm before the roller shutter box. Reason is the expansion of the roller shutter

due to the temperature difference in summer and winter.

•After setting the end positions, lower and raise the motor + shutter to check the set end positions.

Note heat generation

The end position setting without

shutter curtain load leads to more

heat generation in the motor. This

is normal behavior and does not

result in damage to the motor. If

the motor heats up too much, the

thermal protection switch of the motor

is automatically triggered. After a

cooling phase of at least 10 minutes,

the motor is ready for operation again.

MOUNTING INSTRUCTIONS FOR 3T-MOTORS MINI-TUBE MOTORS MOTOR TYPE 3T35/12V

Use proper suspension springs:

•To fasten the roller shutter curtain to the roller shutter shaft, please be sure to use

suitable suspension springs for motor operation. These special mini suspension springs only protrude

approx. 1 mm into the shaft. This allows the shaft to rotate freely. When commercially

springs are used, there will be grinding marks on the motor housing because the suspension pin

protudes too far into the roller shutter shaft, which leads to damage and destruction of the motor.

In case of any kind of grinding marks on the motor housing, the warranty claim is void.

•Mini suspension springs > Optional tubular motor accessories (page 23)

Use correct roller shutter shaft with external fold:

•For steel shafts with a width across ats of 40 mm (SW40), only use shafts with

an external fold. Steel shafts with an internal fold will damage and destroy the motor.

Explanation:

•Avoid overstressing and resulting premature aging of the motor by using the correct suspension

springs and the correct roller shutter shaft with external fold!

•Keep in mind that the motor housing has a diameter of 35 mm and the roller shutter shaft SW40

has an outer diameter of 40 mm. When using commercially available springs or roller shutter shafts

with internal fold, the motor housing will be left with grinding marks, since the suspension pin or the

fold protrude too far into the roller shutter shaft. Contrary to its intended use, the motor runs

permanently against an overload and outside its characteristic data.

•Matching roller shutter shafts SW40 > Optional tubular motor accessories (page 23)

Mini Suspension spring

8-sided shaft SW40

with external fold

Do not use

8-sided shaft SW40

with internal fold!

Suspension spring

INSTALLATION INSTRUCTIONS

3T-MOTORS Tubular motors 12V | Installation instructions

2.1 2.2 2.3 2.4

3T-MOTORS Tubular motors 12V | Installation instructions

INSTALLATION INSTRUCTIONS

INSTALLATION AWNING MOTOR

1Preparation:

•Screw in awning & secure with straps or ropes.

•Remove awning from wall bracket & place on safe surface.

2Prepare motor for installation:

•Slide limit switch adapter ush against motor head. >g. 2.1 / 2.2

•Secure the shaft adapter with the supplied securing bracket. >g. 2.3 / 2.4

3Installation awning motor:

•Remove the cover to access the side bearing (also awning bracket)

and fastening screws. >g. 3.1

•Loosen the screw that secures the side bearing to the support tube. >g. 3.2

•Remove all screws connecting the side bearing

and the crank mechanism. >g. 3.3

•Remove the side bearing from the support tube. >g. 3.4

•Remove the crank mechanism. >g. 3.5

Attention:

Awning arms are under strong tension!

Limit switch adapter

Motor head

Securing bracket

Click

Shaft adapter

Side bearing

Cover

3.1

Support tube

Side bearing

3.2 3.2 3.4

Crank mechanism

•Remove the shaft capsule from the shaft. >g. 3.6

If the shaft capsule is tight, use a hammer and screwdriver.

Be careful not to damage the shaft.

•Push the awning motor with shaft adapter rst into the shaft. >g. 3.7

•Make sure motor head & limit switch adapter are ush in shaft.

•Screw the universal bearing onto the side bearing on the side

facing the awning shaft. >g. 3.8

3.5 3.6 3.7 3.8

Support tube

Shaft capsule

Shaft &

wound up

Awning

Universal

bearing

Shaft &

wound up

Awning

3T-MOTORS Tubular motors 12V | Installation instructions

INSTALLATION INSTRUCTIONS

4Mount solar module SP50:

•Mount the solar module to the wall or roof using one of the following options:

5Connection roller shutter motor + solar module SP50:

•Connect cables of shutter motor and solar module SP50 (see description page 6).

•If the drive should run in the opposite direction after installation, the direction of rotation must be changed via the solar panel SP50.

(see programming page 7).

•Insert the wall brackets (1) into the fasteners and secure them

with the screws (2) supplied.

•Fix the fastenings with the supplied grub screws (3) at the desired

position with hexagonal wrench.

•Mount the wall brackets on the wall with the supplied dowels and screws.

•Attach the clip holder (1) to the wall or roof with suitable screws and dowels.

When doing so, take the desired angle into account.

•Snap the solar module into the clip holder.

Mounting with 2 wall brackets: Mounting with clip bearing:

SP50 Rear with wall brackets SP50 Rear with clip bearing

2 23

1 1

•Slide the side bearing with universal bearing onto the support tube & fasten. >g. 3.9

•Ensure that the motor square spigot is properly engaged in the universal bearing. >g. 3.10

•Secure the motor square spigot with the supplied cotter pin. >g. 3.11

•Attach the cover to the side bearing. >g. 3.12

•Install awning & release fuses.

3.9 3.10 3 .11

Side bearing &

Universal bearing

Support tube

Cotter pin Side bearing

Cover

3.12

3T-MOTORS Tubular motors 12V | Installation instructions

INSTALLATION INSTRUCTIONS

6Setting the end positions: