3TEMP Hipster 1grp User manual

Rev.100319-02-v1
Made in Sweden
Hipster 1GRP 300303
Hioster 2GRP 300304
Hipster
1GRP/2GRP UC
User manual

2
Hipster 1GRP/2GRPUC
Rev.100319-02-v1

3
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
1. Preface
Arvika, Sweden; the home of where the Hipster brewer was created and innovated.
It is in this small industrial town in the middle of Sweden, where hard working men and
women reap their harvest of diligent work; a work of tradition and dedicated skilled
craftsmanship. Arvika is sincerely famous for it’s warmth during the summer, for it’s envi-
ronment of magnicent forests and foremost for the surroundings of 365 smaller lakes,
that enhance mysticism and stories from the past to the present.
The home of the Hipster brewer.
The Hipster is classied by baristas and coee people all over the world as one of the
best amongst lter coee machines. Hipster is a unique brewer. Unlike any other brewer
in the market it let’s you control blooming, temperatures in 3 phases and water distribu-
tion for each recipe. It is designed and developed in Sweden by a team with vast experi-
ence from the coee industry.
The Hipster is a game changer as it brings lter coee to a new level. Precision of ow
rate, temperature and extraction time are critical factors to reach the best possible ex-
traction. In order to preserve the coee’s origin in avour and fragrance, makes the de-
mands high on these 3 parameters precision in order to recreate the same taste experi-
ence time and again.
The fresh water system and the recipe parameters makes a huge impact on the taste
and a tiny impact on the environment as it consumes barely 7 watts when not brewing.
We hope that you will enjoy your new Hipster brewer.
With best wishes
Copyright 2019 All rights reserved
3TEMP/PLAE2TECH
The Story

4
Hipster 1GRP/2GRPUC
Rev.100319-02-v1

Rev.100319-02-v1
Table of contents
1. Preface .........................................................................................3
2. Safety information ................................................................6
2.1 Introduction..........................................................................................6
2.2 This user manual...............................................................................6
2.3 Intended use .......................................................................................6
2.4 Capacity of the machine...............................................................7
2.5 General safety instructions .........................................................7
2.6 Disposal..................................................................................................9
3. Before rst use ........................................................................9
4. Product Description Hipster Brewer ........................ 10
4.1 Description......................................................................................... 10
4.2 The life cycle of The Hipster taste-proling .................... 11
5. Technical data........................................................................12
5.1 HIPSTER 1GRP UC ...........................................................................12
5.2 HIPSTER 2GRP UC ..........................................................................13
5.3 Wiring diagram HeatCase..........................................................14
6. Unpacking................................................................................15
7. Installation Instructions................................................... 16
7.1 Installation Hipster Brewer 1 GRP and 2 GRP UC...........16
7.2 Installation Button controller 1 and 2GRP UC. ................17
7.3 Installation Heat Case ..................................................................17
7.4 Connect the water lter system..............................................18
7.5 Connect the network-cable (RJ45) white cable.............19
7.6 Machine status .................................................................................19
8. User Instructions................................................................. 20
8.1 Prepare a brew ................................................................................20
8.2 Select Recipe ...................................................................................21
8.3 Thermos detachable serving base...................................... 23
9. Recipe settings with button controller................... 24
9.1 Set a recipe........................................................................................ 24
10. Care and maintenance after use.............................. 27
10.1 Cleaning instructions................................................................. 27
10.2 Cleaning thermos........................................................................ 28
10.3 Cleaning water strainer.............................................................31
11. Single brew........................................................................... 32
12. Spare parts ........................................................................... 33
13. Extra additions ................................................................... 34
14. Declaration of conformity............................................ 35
15. Warranty ................................................................................ 36
16. Notes ....................................................................................... 37

6
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
This appliance is intended to be used in applications such as:
- Kitchen areas, shops.
- Oces and other commercial working environments.
- Hotels, motels.
- Bed and breakfast environments.
Switch o the appliance when NOT in use.
Do not use this appliance for anything other than intended use. Any maintenance other
than cleaning should be performed by authorised person.
Do not install the machine in environments in which the temperature is 0 C or less.
Do not use outdoors.
2. Safety information
2.1 Introduction
2.2 This user manual
Information for the user:
Note!
safety instructions
This user manual is an integral part of the appliance and must be kept in an accessible
place under the working life of the appliance.
2.3 Intended use
Warning!
Electric shock hazard!
ALL ELECTRICAL
WORK MUST BE
PERFORMED
BY AN AUTHORIZED
ELECTRICIAN
Save these instructions for future reference.
Caution!
Burn hazard!
Protect your eyes.

7
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
Read all the user instructions before using the machine.This guide contains important in-
structions for proper and safe use of the Hipster brewer. Always keep this manual close at
hand for future reference. We reserve the right for any errors in text or images and any nec-
essary changes made to technical data. In the event of technical problems or any questions.
Please contact our [email protected]
The appliance is only to be installed in locations where it can be overseen by trained
personnel.
The English language is used for the original instructions .
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance in a safe way and if they
understand the hazards involved by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
This appliance can be used by children aged from 8 years and above and persons with re-
duced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way
and understand the hazards involved
Cleaning and user maintenance shall not be made by children without supervision.
The instructions shall state that access to the service area should only be permitted to
persons having knowledge and practical experience of the appliance, in particular as far as
safety and hygiene are concerned.
Indoor use.
Warning! In case of improper use the responsibility is on the user.
2.5 General safety instructions
For the optimal performance of the UC these parameters shall not be exceeded:
Maximum permissible inlet water pressure : 800KPa (8Bar)
Minimum permissible inlet water pressure: 200KPa (2Bar)
Maximum working temperature: 40C
Minimum working temperature: 10 C
2.4 Capacity of the machine.

8
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
Avoid getting the coee machine wet and do not spray liquids onto it. In the event of contact
with liquid immediately switch o the power at the socket or main breaker and dry the appli-
ance thoroughly.
Never immerse the machine, plug or mains cable in water because there is a danger of elec-
tric shock.
Never try to put out a re or ames with water. Turn of the appliance and remove the plug
from the socket, and smother the ames with a re blanket or other appropriate cover.
Do not operate any electrical appliance with a damaged cord or after the appliance has been
damaged in any manner. If the mains cable is damaged it must be replaced by the customer
service to avoid a hazard.
Do not install the machine in environments in which the temperature is 0° C or less.
Do not move the Hipster brewer whilst in operation.
Do not use the Hipster brewer on a sink drain board.
Do not place the Hipster brewer on or near a hot gas or electric burner, or where it could
touch a heated oven.
Keep the appliance and accessories clean. Follow the cleaning instructions provided in this
manual.
Only use original spare parts. The use of spare parts not approved by the
manufacturer could lead to res, electric shocks or personal injury.
Do not place on top of any other appliance.
Appliance must not be cleaned by a water jet.
Electric shock hazard!
This appliance dispense hot water from the brewing hat and may cause injury if not
used correctly. The brew basket must be in place before a recipe is started.
Do not move the brew basket while the coee is being brewed.
Do not touch hot surfaces with your hands; use the handles and buttons.
Burn hazard!

9
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
2.6 Disposal
Do not dispose of the device in household waste! Recycle devices, accessories and pack-
aging. Observe applicable national regulations.
EU only: In accordance with European Directive on waste electrical and electronic
equipment and implementation in national law, used electric power tools must be
collected separately and handed in for environmentally friendly recycling. By collecting and
recycling waste, you help save natural resources, and make sure the product is disposed in
an environmental friendly and healthy way.
Remove all packaging materials attached to your Hipster UC. Ensure that you have
removed all parts and accessories before discarding the packaging.
Clean parts and accessories, lter, basket and thermos. Use warm water and a gentle dish
washing liquid and rinse well. Wipe the outer housing and drip tray with a soft damp cloth and
dry thoroughly.
3. Before rst use
Danger! Do not immerse power cord, power plug for appliance in water or any
other liquid. Do not clean any of the parts or accessories in the dishwasher.
Accept dish try. Important to clean the product propertly.
Important! Ensure that you have removed all parts and accessories before
discarding the packaging.
Note! We recommend that you save the packaging for a possible return
of goods.

10
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
Button controller
Brewer hat
Brew basket
4. Product Description Hipster Brewer
4.1 Description
Thermos 2,5 lThermos 3,8 l
Level tube
Coee tap

11
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
4.2 The life cycle of The Hipster taste-proling
”Regular”
brewer
Target
Pre-brew phase End phase
End phase
Time
Temperature
End phase
+ Blooming
Pre-brew phase

12
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
5. Technical data
5.1 HIPSTER 1GRP UC
Including touch controller, router, cupstand and single brew.
The machine is installed onto the counter and the water units ts under the counter.
Capacity: 1x3,8 lit 200 cups/h.
Dimensions: W220mm/D435mm/H585mm.
Weight: 10 + 6 kg.
Max power hot: 230V 1x2400W.
Max power cold: 1x38W.
Max power idle: 9,6 W.
435
580
220220
181,5
Water inlet
Water Outlet
Power Inlet Drain
HeatCase mounted in
Base Cabinet
262
395,5

13
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
5.2 HIPSTER 2GRP UC
Including touch controller, router, cupstand and single brew.
The machine is installed onto the counter and the water units ts under the counter.
Capacity: 2x3,8 lit 200 cups/h.
Dimensions: W409mm/D402mm/H585mm.
Weight: 10 + 6 kg.
Max power hot: 230V 1x2400W. + 230V 1x2400W
Max power cold: 2x38W.
Max power idle: 19,2 W.
585
439
181.5
276,5
Power Inlet Vent
Water outlet
Water inlet
402
355 61
HeatCase mounted in
Base cabinet
HeatCase 1 HeatCase 2

14
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
5.3 Wiring diagram HeatCase
220 - 240 VAC 2400W (2GRP has two units)

15
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
6. Unpacking
Inlet hose
Router
Coee lter 1x 25. 110/330
Brew basket stainless
Button controller panel
with two straps and two M4 socket screws
Button controller
Single brew lter wire insert
Brew lter wire insert
Main Unit Hipster UC

16
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
Tools needed: Spirit-level
Marker pen
Adjustable spanner
Screwdriver
7. Installation Instructions
7.1 Installation Hipster Brewer 1 and 2 GRP UC ALL ELECTRICAL
WORK MUST BE
PERFORMED
BY AN AUTHORIZED
ELECTRICIAN
Use the drilling template to mark up for the Hipster Brewer UC
Important ! Templet is an extra material in this manual. original size.
Caution! Make sure the brewer is in level, or it will not extract evenly
in the lter-basket. Use a spirit-level.
Min 50mm
10mm
126
126
Hipster UC
Template for drilling main body
Example
Min 50mm
10mm
126
126
Hipster UC
Templatefo rdrilling main body
Hole saw
Hex key
Drilling machine ,drill

17
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
Fasten the Hot water hose to the Hot water out connector.
Connect the hoses and the cords in to the HeatCase.
Button Controller
Hot water hose
Hat Valve
NTC
Mount the Button controller to the Button controller panel with two M4 socket screws included.
Further: Mount the assembly to the Brewer body with the two straps included.
2GRP UC Mount the second Button controller on the opposit side of the body
using the same straps.
Straps
Button controller
Button controller panel
7.2 Installation Button controller 1 and 2 GRP UC
7.3 Installation Heat Case

18
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
7.4 Connect the water lter system.
Note! See manual with the lter set.
Drain
Hot water out
On / Off
Cold water in
Open the lid.
LAN
Button controller
Power inlet
Fasten the cords from below
Hat Valve,
NTC
Router
Caution!
Warning! Close the lid properly in front of the connections.
Tighten the screw in the middle; if not, the warranty will expire.

19
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
0. O
1. Startup
2. Idle Green
4. Running Blue
16. Heater error Red slow blink
19. Connector error Red fast blink
20. Watersupply error Red fast blink
7.5 Connect the network-cable (RJ45) white cable.
To the LAN-port of the router.
7.6 Machine status
State number State name Light
1. Start the router 1 minute before the coee machine, to get an IP-address.
2. Start the machine.
3.A short beep sound means the brewer is on.
4. After 3-8 sec long beep means that the brewer have received an IP-address.
5, Start a run cold. 300-400 ml will be dispensed,
6. Now the Hipster 1GRP/2GRP UC is installed.
You are now ready to brew see page 20.
Note! For 3TEMP to be able to support you in the best possible way,
please connect your Hipster to the internet via LAN, WLAN or GSM.
Use tethering on the router and connect to your existing Wi-Fi.
If you need support, please send us an email to [email protected] or call your
nearest support.
If you want to give us feedback on the product; please send us an email to
[email protected]
recipe
1-8
start/stop
grams of coffee
thermos
1-8
setup
+
HIPSTER

20
Hipster 1GRP/2GRPUC
Rev.100319-02-v1
8.1 Prepare a brew
3. Add lter to the brew basket.
1. Place the thermos under the brewer hat.
8. User Instructions
2. Lift of the brew basket from the brewer hat.
Danger! Can cause serious burns.
Do not remove the brewinghat when lamp is blue and brewing.
Note! Make sure the lter ts correct.
Use 3TEMP coee lter paper.
4. Add coee into the lter.
Note! Make sure the coee is spread
evenly and the surface is at.