A & T International CL82101 User manual

Telephone base installation
If you have
DSL high-speed
Internet service,
a DSL filter (not
included) is
required.
This quick start guide provides you with basic instructions only.
For more complete instructions, refer to your Abridged user’s
manual provided in the package, or see the online Complete
user’s manual at www.telephones.att.com/manuals.
Plug the power
adapter into an
electrical outlet not
controlled by a wall
switch.
Charger installation
Battery installation
Install the battery as shown below. Charge your handset(s) before initial use.
The battery is fully charged after 10 hours of continuous charging.
Quick start guide
CL82101/CL82201/CL82301/CL82351/CL82401/CL82451/
CL82501/CL82551/CL82601
Plug the power cord
and telephone line
cord into the jacks.
Route the
cords through
the slot.
Plug the other end
of the telephone
line cord into a
telephone jack or
a DSL filter.
3. Charge the handset by
placing it face forward
in the telephone base
or charger.
BY 1021
BT183342/BT283342 2.4V 400mAh Ni-MH
BY1021
BT183342/BT283342 2.4V400mAh Ni-MH
Use only the supplied rechargeable battery or replacement battery (model BT166342).
Raise the
antenna.
1
Caution: Use only the power adapter provided with this product. To obtain a replacement, visit
our website at www.telephones.att.com or call 1 [phone].
In Canada, dial 1 [phone].
qCID/VOLUME
Show caller ID history.
Scroll down in menus.
Move cursor to the left when
entering names or numbers.
Decrease listening volume when
on a call, or decrease message
playback volume.
•
•
•
•
MUTE/DELETE
Mute the microphone during a
call.
Delete the displayed entry while
in the directory, call log or redial
list.
Delete digits or characters when
using the dialing keys.
•
•
•
PHONE/FLASH
Make or answer a call.
Answer a call waiting call during
a call.
•
•
/SPEAKERSPEAKER
Switch between the speakerphone
and handset.
pDIR/VOLUME
Show directory entries.
Scroll up in menus.
Move cursor to the right when
entering names or numbers.
Increase listening volume when
on a call, or increase message
playback volume.
•
•
•
•
MENU/SELECT
Show the menu.
Select an item or save an entry
or setting while in the menu.
•
•
OFF/CANCEL
Hang up a call.
Press to cancel an operation,
back up to the previous
menu, or exit the menu display,
or press and hold to return to
idle mode
Press and hold in idle mode to
erase missed call indicator.
•
•
•
REDIAL/PAUSE
Press repeatedly to view the last
10 numbers dialed.
Press and hold to insert a dialing
pause while entering numbers.
•
•
1
Press repeatedly to add or remove 1
in front of the call log entry before
dialing or saving it to the directory.
# (pound key)
Press repeatedly to display other
dialing options when reviewing a
caller ID log entry.
EQ
Change the audio quality to best
suit your hearing.
Quick reference guide
TONE
Press to switch to tone dialing
temporarily during a call if you have
pulse service.
/ANSWER ON
Turn the built-in answering
system on or off.
/REPEAT
Repeat a message.
Press twice to play the
previous message.
•
•
X/DELETE
Delete the message
currently playing.
Press twice to delete
all old messages when
in idle mode.
•
•
/SKIP
Skip to the next message.
/PLAY/STOP
Start or stop message
playback.
Message counter
Shows the number
of messages or other
answering system
information.
Handset
side view
Push to talk
Initiate a one-to-one or
one-to-group broadcast.
Press and hold to broadcast
to a group of handsets.
•
•
q/VOL/p
Adjust the listening
volume during
message playback.
Adjust the base ringer
volume when in idle
mode.
•
•
Initial settings
We recommend you program your telephone system before use.
The following are a few examples of common features to set before using the
telephone. Refer to the Handset settings and Answering system settings in
the Abridged user’s manual or the online Complete user’s manual for detailed
instructions on setting all telephone features.
Set date/time
Set the date/time before using the answering system.
1. MENU -> qor p-> Set date/time -> SELECT.
2. qor pto choose month, or enter the number -> SELECT.
3. qor pto choose day, or enter the number -> SELECT.
4. qor pto choose year, or enter the number -> SELECT.
5. qor pto choose hour, or enter the number -> SELECT.
6. qor pto choose minute, or enter the number -> SELECT.
7. qor pto choose AM or PM -> SELECT.
Record your own announcement
Your outgoing announcement plays when calls are answered by the answering
system. You can use the preset announcement to answer calls, or replace it
with your own recorded announcement.
1. MENU -> qor p-> Answering sys -> SELECT.
2. SELECT to select Announcement.
3. qor p-> Record annc -> SELECT.
4. Facing the handset, record your announcement and press 5to end recording.
Number of rings
You can set the answering system to answer an incoming call after 2, 3, 4, 5 or
6 rings, or toll saver. If you choose toll saver, the answering system answers a
call after 2 rings if you have new messages, and after 4 rings when there are
no new messages.
If you want the built-in answering system instead of the voicemail to answer
a call, you should set the answering system to answer a call at least 2 rings
before the voicemail is set to answer. Contact your telephone service provider
for information on your voicemail settings.
1. MENU -> qor p-> Answering sys -> SELECT.
2. qor p-> Ans sys setup -> SELECT.
3. qor p-> # of rings -> SELECT.
4. qor p-> Choose among 2, 3, 4, 5, 6 or Toll Saver -> SELECT.
Handset ringer volume
You can set the ringer volume level to one of the six levels or turn the
ringer off.
1. MENU -> qor p-> Ringers -> SELECT.
2. SELECT to select Ringer volume -> SELECT.
3. qor pto choose the desired level -> SELECT.
Language
If you want to change the display language, or you have accidentally changed
the language and want to switch it back to English, follow the steps below.
1. MENU -> q7 times -> SELECT twice.
2. qor pto choose the desired language, or choose English if you want to
change the display language to English -> SELECT.
2 3
1. Plug the battery
connector securely
into the socket inside
the handset battery
compartment, matching
the color-coded label.
Insert the supplied
battery with the label
THIS SIDE UP facing up
as indicated.
2. Align the cover
flat against
the battery
compartment,
then slide it
upwards until it
clicks into place.
Handset
Telephone base

Telephone operation
Operation Steps
Making a call Press PHONE or /SPEAKERSPEAKER -> Enter the telephone
number.
On-hook dialing
(predialing)
Enter the telephone number -> Press PHONE or
/SPEAKERSPEAKER to call.
Answering a call Press PHONE or /SPEAKERSPEAKER, or press any dialing keys
(0-9,TONE or #).
Ending a call Press OFF or return the handset to the telephone base
or charger.
Speakerphone During a call, press /SPEAKERSPEAKER to switch between
handsfree speakerphone and normal handset use.
Redial Press REDIAL repeatedly to select the desired entry ->
PHONE or /SPEAKERSPEAKER to call.
Volume control Press VOLUMEqto decrease or press VOLUMEpto
increase the listening volume during a call.
Call waiting
(Requires subscription
from telephone
service provider)
Press FLASH to put current call on hold and to take the
new call; press again to switch back and forth between
calls.
Caller ID
This product supports caller ID services offered by most telephone service providers.
The telephone stores caller ID information for the last 50 incoming calls in the
telephone base. This information is common to all handsets.
Missed call indicator
When a handset is in idle mode and has new or missed calls, its screen shows
XX Missed calls.
You can erase the missed call indicator either by reviewing the call log one by
one, or by pressing and holding CANCEL on the handset in idle mode.
Review and dial a number in the call log
1. CID in idle mode -> qor pto scroll through the list.
2. PHONE or /SPEAKER to call when the desired entry is displayed.
Caller ID announce
When this feature is on and you have an incoming call, the handset and/or
base speaks “Call from...” and the name of the caller based on the directory
or caller ID information. You can turn this feature off for the base or each
individual handset, or both.
1. MENU -> qor p-> Settings -> SELECT.
2. qor p-> Caller ID annc -> SELECT.
3. qor pto choose HANDSET or BASE -> SELECT.
4. qor pto choose On or Off -> SELECT.
Directory
The directory can store up to 50 entries, which are shared by all system handsets.
Operation Steps
Adding an entry 1. MENU.
2. qor p-> Directory -> SELECT.
3. qor p-> Add contact -> SELECT.
4. Enter a telephone number up to 30 digits -> SELECT.
5. Enter a name up to 15 characters -> SELECT.
Searching/dialing
an entry
1. DIR in idle mode.
2. Press qor pto browse through the directory, or press
the dialing keys (0-9) to start a name search.
3. Press PHONE or /SPEAKER to call.
Answering system
About answering system and voicemail
Your telephone has separate indicators for two different types of voice messages:
those left on the built-in answering system and those left at your telephone
service provider’s voicemail. To listen to messages recorded on the built-in
answering system, refer to the Message playback section below; to listen to
voicemail, contact your telephone service provider for more information.
Turn answering system on/off
The answering system must be turned on to answer and record messages.
Press /ANSWER ON on the telephone base to turn the built-in answering
system on or off.
When it is turned on, the /ANSWER ON light on the telephone base turns on
and ANS ON displays on the handset.
Message alert tone
When this feature is on, and there is at least one new message, the telephone
base beeps every 10 seconds.
1. MENU -> qor p-> Answering sys -> SELECT.
2. qor p-> Ans sys setup -> SELECT.
3. qor p-> Msg alert tone -> SELECT.
4. qor p-> On or Off -> SELECT.
Call screening
Use this feature to choose whether incoming messages can be heard over the
telephone base speaker when they are being recorded. If you turn call screening
on, you hear the incoming message. While monitoring an incoming message, you
can answer the call by pressing PHONE or /SPEAKERSPEAKER on the handset.
1. MENU -> qor p-> Answering sys -> SELECT.
2. qor p-> Ans sys setup -> SELECT.
3. SELECT to select Call screening.
4. qor p-> choose On or Off -> SELECT.
Message playback
Using the telephone base:
Press /PLAY when the telephone base is in idle mode.
Using a handset:
Press MENU twice when the handset is in idle mode.
Options during playback
Feature On the telephone base On a handset
Adjust playback volume Press q/VOL/pPress qVOLUME or
pVOLUME
Stop playback Press /STOP Press 5
Skip to the next message Press /SKIP Press 6
Repeat the message Press /REPEAT Press 4
Play the previous message Press /REPEAT twice Press 4 twice
Delete the message Press X/DELETE Press DELETE
For more detailed instructions, please refer to the Abridged user’s manual
provided in your package, or for a full set of installation and operation
instructions, refer to the online CL82101/CL82201/CL82301/CL82351/
CL82401/CL82451/CL82501/CL82551/CL82601 DECT 6.0 cordless
telephone/answering system with caller ID/call waiting Complete user’s
manual at www.telephones.att.com/manuals.
For customer service or product information, visit our website at
www.telephones.att.com or call 1 [phone]. In Canada, dial
1 [phone].
© 2010-2011 Advanced American Telephones. All Rights Reserved.
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219.
Printed in China. Issue 7 AT&T 09/11.