A1 Security Cameras speco O2PH2 User manual
Quick Start Guide
2MP Pinhole/ATM IP Camera -
O2PH2 -
Available from A1 Security Cameras
Version 1 0 0 -
Welcome
Thank you for purchasing this network camera! -
Please read this manual carefully before operating the unit and retain it for future reference. -
Should you require any technical assistance, please contact Speco Technologies Technical Support. -
Important Safeguards and Warnings
1
．
．．
．
Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified listed 12VDC Class 2 power supply only.
Please note: Do not connect two power supplying sources to the device at the same time; it may result in device
damage! The product must be grounded to reduce the risk of electric shock
Improper handling and or installation could run the risk of fire or electrical shock.
2
．
．．
．
Environment
Heavy stress, violent vibration or exposure to water is not allowed during transportation, storage and installation. -
This product should be installed in a cool, dry place away from direct sunlight and heat sources. -
Do not install the product in extreme temperature conditions. -
Do not expose the camera to electromagnetic radiation. Otherwise it may result in CMOS sensor failure. -
Do not block any ventilation openings. -
Do not allow water and liquid intrusion into the camera. -
3 Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any maintenance work. -
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface. -
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth dampened with a small -
quantity of neutral detergent. Finally use the dry cloth to clean the device. -
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure cleaning (such as using -
cloth) may result in a poor image. -
The grounding holes of the product are recommended to be grounded to further enhance the reliability of the -
camera. -
Dome cover is an optical device, please don’t touch or wipe cover surface directly during installation and use, please -
refer to the following methods if dirt is found: -
Stained with dirt -
Use oil-free soft brush or hair dryer to remove it gently. -
Stained with grease or fingerprint -
Available from A1 Security Cameras
i
Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change
the cloth and wipe several times if it is not clean enough.
Warning
• This camera should be installed by qualified personnel only.
• All the examination and repair work should be done by qualified personnel.
• Any unauthorized changes or modifications could void the warranty.
• As a security measure, for installations not on a plug and play NVR, make sure to modify the default password
after login.
• Do not use more than one power source for the device.
Statement
This guide is for reference only. -
Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to -
modify these without notice and without incurring any obligation. -
Speco Technologies is not liable for any loss caused by improper operation. -
FCC Information
1 - FCC conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference
• This device must accept any interference received, including interference that may cause undesired operation.
2 - FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment
generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communication. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Note
Before installation, check the package and make sure that all components are included. -
Contact your rep or Speco customer service department immediately if something is broken or missing in the -
package. -
Available from A1 Security Cameras
ii
Accessory Name Amount
Main Unit 1
Lens Unit 1
Quick Start Guide 1
Installation Accessories Bag 1
CD 1
Available from A1 Security Cameras
iii
Table of Contents -
1 Device Specifications................................................................................................................................ 1
1.1 Structure and Dimensions .......................................................................................................... 1
1.1.1 Structure.............................................................................................................................. 1
1.1.2 Dimensions.......................................................................................................................... 3
1.2 Bidirectional Audio...................................................................................................................... 3
1.2.1 Device-end to PC-end......................................................................................................... 3
1.2.2 PC-end to Device-end......................................................................................................... 4
1.3 Alarm Setup................................................................................................................................ 4
2 Device Installation..................................................................................................................................... 5
3 IP Scanner................................................................................................................................................. 6
3.1 Operation.................................................................................................................................... 6
4 Web Operation.......................................................................................................................................... 7
4.1 Login and Main Interface............................................................................................................ 7
Available from A1 Security Cameras
iv
1 Device Specifications
1.1 Structure and Dimensions
1 1 1 Structure
The following figures show the ports of the main unit.
Figure 1-1 Ports of the main unit (1)
Figure 1-2 Ports of the main unit (2) -
The following table shows the detailed information of the ports. -
Available from A1 Security Cameras
1
Table 1-1 Description of Port Functions -
No Port Connector Function Description
1 Audio Out RCA Audio output to speaker
2 Audio In RCA Audio input. Connect a microphone.
3 Micro SD
Micro
SD
Card slot Micro SD card slot for edge recording
4 Sensor USB-A For connecting the lens unit to the main unit
5 LAN Ethernet
port For data or PoE
6 DC12V Terminal
block 12V DC
7 I O Terminal
block
Alarm inputs and outputs. Refer to Table 1-2 for
more details.
8 Reset Button - Continuously press the button for over 5 seconds to
restore the device to factory default settings.
Table 1-2 Description of I/O -
Port name Cable port name Function description
G GND
TX 232 sending port.
RX 232 receiving port.
IN1 Alarm input port1 receives on-off signal from
external alarm source.
I O port IN2 external alarm source.
G GND
N1
Alarm output port1
Alarm input port 2
，
，
receives on-off signal from
C1
N2
Alarm output port2
C2
Available from A1 Security Cameras
2
1.1.2 Dimensions
Refer to the following figures for dimension information of the lens unit and the main unit. Measurements
are in mm.
Figure 1-3 Lens Unit
Figure 1-4 Main Unit -
1.2 Bidirectional Audio
1 2 1 Device-end to PC-end
Device Connection
First, connect a microphone to the audio input port of the device. Then connect a speaker to the audio
output port of the PC. Log in to the web viewer’s live view page and then click the microphone button on the
top right corner to enable the bidirectional audio function.
Available from A1 Security Cameras
3
hen connect a speaker to the audio output port of the device. Log in to
hen click the microphone button on the top right cor
o t
to the alarm
then configure the
onds
settings
Enable microphone input on the PC. e device. Log in to
the web viewer’s live view page and
er to enable the
outpu
alarm input device
alarm output devic
be connected to
and
rm
corres
in the we
output
Enable microphone input on the PC. Then connect a speaker to the audio output port of t
can onl
Al
. The alarm output corresponds to the alar
1 2 2 PC-end to Device-end
Device Connection
Enable microphone input on the PC. T
Then connect a speaker to the audio output port of th
he device. Log in to
the web viewer’s live view page and t
then click the microphone button on the top right cor
n
ner to enable the
bidirectional audio function.
1.3 Alarm Setup
Figure 1-5 Alarm setup screen
To set up the Alarm input and
output
t
, do the following:
1. - Connect the
alarm input device t
to t
he alarm input port.
2. - Connect the
alarm output device
e to the alarm
output port. Alarm output port
can only
y be connected to
a
“N O” alarm device.
3. - Open the web setup page,
and
then configure the
alarm input and output in the
Ala
arm
section. Alarm
input in the web settings
corresp
ponds
to the Alarm input on the I O port.
4. - Set the alarm output
in the web
b settings
. The alarm output corresponds to the alarm
m output
on the I O
port.
Available from A1 Security Cameras
4
2 Device Installation
Note
Please make sure the installation surface can support at least the 3X weight of the total weight of the camera -
and the main unit. -
The following figure shows the installation of the main unit: -
Figure 2-1 Installation of main unit
1. Stick the installation template on the designated surface where the device will be installed.
2. Drill holes according to the positions on the installation template.
3. Take out the expansion bolts and insert them into the holes that have been drilled.
4. Tighten the 3 screws to fix the device on the installation surface where the bolts are located.
5. Put the main unit into the installation bracket directly.
6. Connect lens unit to the main unit with the cable that’s attached to the lens unit.
Available from A1 Security Cameras
5
Figure 2-2 Installation of lens unit -
1. Take out the installation bracket from the accessories bag (with installation foam)
2. Tear off the film of the foam, and stick it on the surface to be installed.
3. Set the fixing ring on the installation bracket.
4. Put the round front end into the installation bracket and adjust the location.
5. Tighten the fixing ring.
3 IP Scanner
IP Scanner can search for the device on the local network. -
Please note that only devices that are on the same subnet can be discovered. -
The device is set to DHCP mode by default. -
3.1 Operation
Open up IP Scanner.
Error! Reference source not found.
In the device list, you can view the IP address, model number, and MAC address of each device. Select the
applicable device and double click to open up the web viewer.
Available from A1 Security Cameras
6
agement via a web browser on a PC.
e
camera address in the address bar or double click the device in IP
ma
Login and Main Interfa
Open the browser and input networ device in IP
Open the browser and input network camera address in the address bar or double click th
Figure 3-1
4 Web Operation
This device supports viewing and
man
nagement via a web browser on a PC.
4.1
Login and Main Interfac
ce
Open the browser and input network
k camera address in the address bar or double click the
e device in IP
Scanner. See Figure 4- 1.
Available from A1 Security Cameras
7
. See
ssword.
word is
change the password after initial login
nstall applicable plugins.
The login interface is shown as belo
Please input your user name and p
and pas
Note: For security purposes, pleas
After logging in, follow directions to
Input your IP
address
here
Figure 4- 1 IP address
The login interface is shown as below
w. See
Figure 4- 2. -
Please input your user name and pa
assword. -
Default user name is admin
and pass
sword is
1234. -
Note: For security purposes, please
e change the password after initial login -
Figure 4- 2 Web login
After logging in, follow directions to i
install applicable plugins.
Available from A1 Security Cameras
8
Table of contents
