Geutebruck G-Cam/ESD-4630 User manual

G-Cam/ESD-4630 H.265 IR Speed Dome IP Camera Quick Guide
This guide is for quick installing and connecting the Speed Dome IP Camera. For more details, please refer to the
User’s Manual.
Installation Notices
This camera must be installed by qualified personnel and the installation should conform to all local codes.
Do not replace batteries of the camera. Risk of explosion may occur if the battery is replaced by an incorrect type.
To use an external power supply, please contact the camera manufacturer to
confirm that the power supply uses the same power specifications as the
camera. The power supply must comply with the LPS requirements.
For safety concern, please hook up the camera with the anti-drop chain of the
pendant when installing the camera. For more information about pendant and
anti-drop chain, please contact the camera manufacturer.
Camera’s Connectors
No.
Connector
Definition
1
Power Connector (DC12V)
DC12V power connection
2
RJ-45 Port*
For network and HighPoE connections 60W
3
Power Connector (AC24V)
AC24V power connection
4
Reset Button
Press the button with a proper tool for at least 20 seconds to
restore the system.
5
Audio/Alarm I/O & RS-485 Connector**
Audio/Alarm I/O &
RS-485 connection (not supported)
6
BNC
For analog video output
7
SD Card Slot
Insert the SD card into the card slot to store videos and
snapshots. Do not remove the SD card when the camera is
powered on.
*Please contact the manufacturer for compatible PoE injector.
**Do NOT connect external power supply to the alarm I/O connector of the camera, RS-485 is not supported.
NOTE: It is not recommended to record with the SD card for 24/7 continuously, as it may not be able to support
long term continuous data read/write. Please contact the manufacturer of the SD card for information regarding
the reliability and the life expectancy.
Power Connection
To power up the camera, connect the DC12V or AC24V power adaptor to the power connector of the camera and the
power outlet. Refer to the diagram and pin definition below for AC24V power connection.
Pin
Definition
1
AC24V L
2
GND
3
AC24V N
Alternatively, users can use an Ethernet cable and connect it to the RJ-45 port of the camera and an HighPoE switch.
Zero Downtime Power Switching (ZDT)
When users connect DC12V power jack and the RJ-45 port at the same time, the power input comes from the DC12V
connector. If the DC12V power source fails, the camera will switch power input seamlessly to the RJ-45 port until the
DC12V power source is restored.
Ethernet Cable Connection
Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to
the network switch or PC.
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the
PC.
NOTE: Check the status of both power and network activity indicator LEDs. If either LED is unlit, please check
the corresponding connection.
Green Power LED lights up when the camera is powered up.
Orange Network LED (1) flashes when data is being transmitted over network,
(2) lights up for good network connection.
NOTE: The ITE is to be connected only to PoE networks without routing to the outside plant or equivalent
description.
Audio/AIarm I/O & RS-485 Connection
Please refer to the diagram and pin definition tables below for audio/alarm I/O & RS-485 connection.
Pin
Definition
Pin
Definition
Pin
Definition
Pin
Definition
1
Audio Out
5
Alarm Out B1
9
Alarm In 4
13
GND (Alarm I/O and RS-485)
2
GND (Audio I/O)
6
Alarm Out B2
10
Alarm In 3
14
Audio In
3
Alarm Out A1
7
RS-485 D+*
11
Alarm In 2
4
Alarm Out A2
8
RS-485 D-*
12
Alarm In 1
* Not supported
Before Login to the Camera
A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and plug-
ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual.
ActiveX Controls and Plug-ins Settings
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>, and click on <Custom level> to
change ActiveX settings.
Step 4: Set “ActiveX controls and plug-ins” items to
<Prompt> or <Enable>.
Step 1: Start the IE Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
<Internet>.
Step 4: Down the page, click on <Default Level> and
<OK> to confirm the setting. Close the browser
window, and open a new one later for
accessing the IP camera.
NOTE: For the system requirement of the web browser, it is required to connect the camera with Microsoft
Internet Explorer 10.0 or later version to ensure smooth operation.
2 3

Camera Login
The default IP address of the camera is: 192.168.0.250. Therefore, to access the camera for the first time, please set
the IP address of the PC as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID & Password
Key in the camera’s IP address in the URL bar of the web browser window and hit “Enter”.
Enter the default username ( Note that username is
case sensitive.
root) and password (admin) in the prompt request dialogue.
Install the ActiveX Control
After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
Right click on the information bar and click on <Install ActiveX Control…> to permit ActiveX control installation.
In the pop-up security warning window, click on <Install> to start downloading DCViewer software on the PC.
Click on <Finish> after DCViewer installation is completed.
Browser-based Viewer
The main page of the IP camera user interface is as shown below.
NOTE: For details about configuring the camera in GEUTEBRÜCK-Software (G-Set), please refer to
the Quick Guides, which can be found on the supplied CD ROM.
G-Cam/ESD-4630
Network IR Speed Dome Camera
Quick Guide
Ver. 1.0
4