AAA Storage Sheds Glider User manual

Tools needed:
•  Wrench
•  Wrench
• Rubber Mallet or Hammer
• #2 Square Drive Screwdriver
or Power Drill  Driver
Package Contents
NOTE: Do not tighten any bolts
until step 4 is completed.
1 - Seat (A)
2 - Base Crosspiece (G)
4 - Glider Bearing (O)
1 - Back (B) - style may vary
1 - Le Arm (C) 1 - Right Arm (D)
1 - Right Base Leg (E) 1 - Le Base Leg (F)
Glider Assembly Instructions
Package contents continued on inside.
Step 7
Step 9
Step 8
Slide a washer (L) onto each bolt on the inside of
the leg.
Set the base into place. MAKE SURE YOU DON’T PUT
IT ON BACKWARDS. (See step 5, fig. A and fig. B.)
Now insert a5⁄16"bolt through the hole in the base,
this time with the threads pointing out (heads facing
in). Slide a washer (L) onto the bolt, and then attach
it to the glider bearing (O) with a lock nut (M). Repeat
on all four corners.
Now tighten ALL your bolts, and your glider is
complete. Enjoy!
Slide a glider bearing (O) onto each bolt. Make sure it
is turned the way it shows in the above picture. Now,
turn a lock nut (M) loosely on each bolt.
NOTE: Now make sure all the bolts have been tight-
ened before continuing to Step 9.

Step 1 Step 2
Lay seat (A) on a flat surface and slide back (B)
into seat as shown.
Tap bolts (H) into holes as shown with the heads
pointing toward the outside. Repeat on other end
and centers.
NOTE: Amount of centers may vary.
Step 3
Turn flange nuts (I) loosely onto the bolts.
NOTE: Do not tighten them until step 4 is completed.
Step 4
Step 6
Attach right arm (C) with two ¼" long bolts (J)
through legs, and one ¼" short bolt (H) through
arm and turn flange nuts (I) loosely onto the bolts.
Repeat on other end with le arm (D).
NOTE: You may have to push up or down, forward or
backward, on the back or arm assembly to line up
the bolt holes.
Turn the whole seat assembly upside down, and
insert a 5⁄16"bolt (K) into each leg with the threads
pointing in toward center (heads facing out). Use a
rubber mallet and drive the square nibs of the bolt
firmly into the material to prevent the bolt from
spinning when you tighten the nut.
Step 5
To assemble the glider base, you have to attach
the base crosspieces (G) to the base legs (E) and (F)
using 1¾" screws (N)
NOTE the dierence in the front and the back of the
base as shown in figure (A) and figure (B) below.
See the dierence in the length of
fig. A and fig. B at the arrow.
Package Contents Continued from front page
Hardware Package
4 - ¼"Long Bolt (J)
10 - ¼"Short Bolt (H)
8 - 5⁄16"Bolt (K)
12 - 1¾"Screw (N) 1 - Bit (P)
8 - 5⁄16" Locknut (M)
8 - 5⁄16"Washer (L)
14 - ¼" Flange Nut (I)
Short
Bolt (H)
Short
Bolt (H)
Long
Bolt (J) Long
Bolt (J)
fig. A
Front Side
fig. B
Back Side

Step 1 Step 2
Lay seat (A) on a flat surface and slide back (B)
into seat as shown.
Tap bolts (H) into holes as shown with the heads
pointing toward the outside. Repeat on other end
and centers.
NOTE: Amount of centers may vary.
Step 3
Turn flange nuts (I) loosely onto the bolts.
NOTE: Do not tighten them until step 4 is completed.
Step 4
Step 6
Attach right arm (C) with two ¼" long bolts (J)
through legs, and one ¼" short bolt (H) through
arm and turn flange nuts (I) loosely onto the bolts.
Repeat on other end with le arm (D).
NOTE: You may have to push up or down, forward or
backward, on the back or arm assembly to line up
the bolt holes.
Turn the whole seat assembly upside down, and
insert a 5⁄16"bolt (K) into each leg with the threads
pointing in toward center (heads facing out). Use a
rubber mallet and drive the square nibs of the bolt
firmly into the material to prevent the bolt from
spinning when you tighten the nut.
Step 5
To assemble the glider base, you have to attach
the base crosspieces (G) to the base legs (E) and (F)
using 1¾" screws (N)
NOTE the dierence in the front and the back of the
base as shown in figure (A) and figure (B) below.
See the dierence in the length of
fig. A and fig. B at the arrow.
Package Contents Continued from front page
Hardware Package
4 - ¼"Long Bolt (J)
10 - ¼"Short Bolt (H)
8 - 5⁄16"Bolt (K)
12 - 1¾"Screw (N) 1 - Bit (P)
8 - 5⁄16" Locknut (M)
8 - 5⁄16"Washer (L)
14 - ¼" Flange Nut (I)
Short
Bolt (H)
Short
Bolt (H)
Long
Bolt (J) Long
Bolt (J)
fig. A
Front Side
fig. B
Back Side

Tools needed:
•  Wrench
•  Wrench
• Rubber Mallet or Hammer
• #2 Square Drive Screwdriver
or Power Drill  Driver
Package Contents
NOTE: Do not tighten any bolts
until step 4 is completed.
1 - Seat (A)
2 - Base Crosspiece (G)
4 - Glider Bearing (O)
1 - Back (B) - style may vary
1 - Le Arm (C) 1 - Right Arm (D)
1 - Right Base Leg (E) 1 - Le Base Leg (F)
Glider Assembly Instructions
Package contents continued on inside.
Step 7
Step 9
Step 8
Slide a washer (L) onto each bolt on the inside of
the leg.
Set the base into place. MAKE SURE YOU DON’T PUT
IT ON BACKWARDS. (See step 5, fig. A and fig. B.)
Now insert a5⁄16"bolt through the hole in the base,
this time with the threads pointing out (heads facing
in). Slide a washer (L) onto the bolt, and then attach
it to the glider bearing (O) with a lock nut (M). Repeat
on all four corners.
Now tighten ALL your bolts, and your glider is
complete. Enjoy!
Slide a glider bearing (O) onto each bolt. Make sure it
is turned the way it shows in the above picture. Now,
turn a lock nut (M) loosely on each bolt.
NOTE: Now make sure all the bolts have been tight-
ened before continuing to Step 9.