AARC TECHNOLOGIES Aarcantennas MKT20-V100 User manual

Specifications may change at any time without notice.
www.aarcantennas.com
Installation Instructions
Refer to the Parts Table
below to check the all mounting kits are included
serious physical damage on the parts to avoid any installation
Notice:
All the work on
installation, maintenance, or removal
qualified with
experienced personnel.
once a year to ensure the orientations and connections are work as normal.
Caution:
1. Do not install near the
ower
2. Do not install it in the wet-
day, windy day, either lightning or thunder, do not use a metal
ladder at the same time.
3. It strongly recommends
when working on installation that wearing a pair of shoes
soles and heels, protective clothing with a long
Mounting Hardware
©Copyright
AARC
TECHNOLOGIES
Installation Instructions
below to check the all mounting kits are included
serious physical damage on the parts to avoid any installation
failed.
NO.
1
Antenna pivot arm
2
Bracket
3
Bracket
4
Mount clamp
5 C
alibration Tablets
6
M12×1
7
M12
8 φ1
2
9 φ12
Sp
10
M1
11
M10 Hex Nut
12 φ1
0
13 φ10
Sp
14
M12×1
15
M
16
M
17 Φ8
18 Φ8
Sp
installation, maintenance, or removal
to the antenna
system is
experienced personnel.
It recommends that keep a check on the Antenna Systems
once a year to ensure the orientations and connections are work as normal.
ower
Lines
or Guy Wires to prevent getting an electric shock.
day, windy day, either lightning or thunder, do not use a metal
when working on installation that wearing a pair of shoes
soles and heels, protective clothing with a long
-sleeve and rubber gloves.
Mounting Hardware
MKT20-V100
12AUG2015
TECHNOLOGIES
CO
.,
LT
.,
All
Rights
Reserved.
below to check the all mounting kits are included
; check if there is a
Name Qty
Antenna pivot arm
2
Bracket
1 1
Bracket
2 1
Mount clamp
4
alibration Tablets
1
M12×1
30 Bolt 4
M12
Hex Nut 20
2
Flat Washer 16
Sp
ring Washer 16
M1
0×25 Bolt 4
M10 Hex Nut
4
0
Flat Washer 4
Sp
ring Washer 4
M12×1
80 Bolt 4
M
8×35 Bolt 2
M
8 Hex Nut 4
Flat Washer 2
Sp
ring Washer 2
system is
required by
It recommends that keep a check on the Antenna Systems
or Guy Wires to prevent getting an electric shock.
day, windy day, either lightning or thunder, do not use a metal
when working on installation that wearing a pair of shoes
with rubber

Specifications may change at any time without notice.
www.aarcantennas.com
Detailed steps
1.
Fix and
to the top bracket
3.
Fix the lower clamp at the proper position
of the mounting pol
5.
Fix upper clamp at the mounting pol
t
hen fasten all the nuts
Tightening Nut Hex Torque Values
Tightening
Connector Type
Mounting Hardware
©Copyright
AARC
TECHNOLOGIES
Fix and
ensure the top mounting stable
to the top bracket
by M8*20 bolts and nuts.
2.
Fix and
stable
to the bottom bracket
bolts and nuts.
Fix the lower clamp at the proper position
of the mounting pol
e.
4.A
djust the downtilt
Fix upper clamp at the mounting pol
e,
hen fasten all the nuts
tightly.
6.A
djust the downtilt
then lock the bolt.
Tightening Nut Hex Torque Values
Dia Tension
M8 16-22N.m
M10 32-40N.m
Tightening
Connector Torque Values
Connector Type
Tension
7-16 DIN 25-30N.m
Mounting Hardware
MKT20-V100
12AUG2015
TECHNOLOGIES
CO
.,
LT
.,
All
Rights
Reserved.
Fix and
ensure the bottom mounting
to the bottom bracket
by M8*20
bolts and nuts.
djust the downtilt
angle to 0 degree.
djust the downtilt
angle to X degree,
then lock the bolt.