Aasset AAC-2022TI User manual

High-Definition IR Water-Proof
Bullet Camera
User Manual

High-Definition IR Water-Proof Bullet Camera·User Manual
1
1
Thank you for purchasing our product. If there are any questions,
or requests, please do not hesitate to contact the dealer.
This manual applies to AAC-2022TI bullet camera.
This manual may contain several technical incorrect places or
printing errors, and the content is subject to change without notice.
The updates will be added to the new version of this manual. We
will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested for fire, shock or casualty hazards
as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the
security or signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY
OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS
PRODUCT.”

High-Definition IR Water-Proof Bullet Camera·User Manual
2
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to
comply with the limits for a digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized
European standards listed under the Low Voltage Directive
2006/95/EC, the EMC Directive 2004/108/EC.

High-Definition IR Water-Proof Bullet Camera·User Manual
3
3
2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product
contains a battery that cannot be disposed of as
unsorted municipal waste in the European Union.
See the product documentation for specific battery
information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd),
lead (Pb), or mercury (Hg). For proper recycling, return the battery
to your supplier or to a designated collection point. For more
information see: www.recyclethis.info.

High-Definition IR Water-Proof Bullet Camera·User Manual
4
4
Safety Warnings and Cautions
Please pay attention to the following warnings and
cautions:
Hazardous Voltage may be present: Special
measures and precautions must be taken when
using this device. Some potentials (voltages) on the
device may present a hazard to the user. This device
should only be used by Employees from our company with
knowledge and training in working with these types of devices that
contain live circuits.
Power Supply Hazardous Voltage: AC mains voltages
are present within the power supply assembly. This device must be
connected to a UL approved, completely enclosed power supply, of
the proper rated voltage and current. No user serviceable parts
inside the power supply.
System Grounding (Earthing): To avoid shock, ensure
that all AC wiring is not exposed and that the earth grounding is
maintained. Ensure that any equipment to which this device will be

High-Definition IR Water-Proof Bullet Camera·User Manual
5
5
attached is also connected to properly wired grounded receptacles
and are approved medical devices.
Power Connect and Disconnect: The AC
power supply cord is the main disconnect device to
mains (AC power).The socket outlet shall be
installed near the equipment and shall be readily
accessible.
Installation and Maintenance: Do not connect/disconnect
any cables to or perform installation/maintenance on this device
during an electrical storm.
Power Cord Requirements: The connector
that plugs into the wall outlet must be a
grounding-type male plug designed for use in your
region. It must have certification marks showing certification by an
agency in your region. The connector that plugs into the AC
receptacle on the power supply must be an IEC 320, sheet C13,
female connector. See the following website for more information
http://kropla.com/electric2.htm.
Lithium Battery: This device contains a Lithium Battery. There
is a risk of explosion if the battery is replaced by an incorrect type.
Dispose of used batteries according to the vendor’s instructions
and in accordance with local environmental regulations.

High-Definition IR Water-Proof Bullet Camera·User Manual
6
6
Perchlorate Material: Special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate. This notice is
required by California Code of Regulations, Title 22, Division 4.5,
Chapter 33: Best Management Practices for Perchlorate Materials.
This device includes a battery which contains perchlorate material.
Taiwan battery recycling:
Please recycle batteries.
Thermal and Mechanical Injury: Some
components such as heat sinks, power regulators,
and processors may be hot; care should be taken
to avoid contact with these components.
Electro Magnetic Interference: This equipment has not
been tested for compliance with emissions limits of FCC and similar
international regulations. This device is not, and may not be,
offered for sale or lease, or sold, or leased until authorization from
the United States FCC or its equivalent in other countries has been
obtained. Use of this equipment in a residential location is
prohibited. This equipment generates, uses and can radiate radio
frequency energy which may result in harmful interference to radio
communications. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is
required to take measures to eliminate the interference or
discontinue the use of this equipment.

High-Definition IR Water-Proof Bullet Camera·User Manual
7
7
Lead Content:
Please recycle this device in a responsible
manner. Refer to local environmental
regulations for proper recycling; do not dispose
of device in unsorted municipal waste.

High-Definition IR Water-Proof Bullet Camera·User Manual
8
8
Safety Instruction
These instructions are intended to ensure that user can use the
product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the
warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the
cautions are neglected.
Warnings
Please adopt the power adapter which can meet the safety
extra low voltage (SELV) request. And source with DC 12V or
AC 24V (depending on models) according to the IEC60950-1
and Limited Power Source standard.
If the product does not work properly, please contact your
dealer or the nearest service center. Never attempt to
disassemble the camera yourself. (We shall not assume any
Warnings Follow these
safeguards to prevent
serious injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

High-Definition IR Water-Proof Bullet Camera·User Manual
9
9
responsibility for problems caused by unauthorized repair or
maintenance.)
To reduce the risk of fire or electrical shock, do not expose this
product to rain or moisture.
This installation should be made by a qualified service person
and should conform to all local codes.
Please install blackouts equipment into the power supply
circuit for convenient supply interruption.
Please make sure that the ceiling can support more than 50(N)
Newton gravities if the camera is fixed to the ceiling.
Cautions
Make sure the power supply voltage is correct before using the
camera.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is
necessary, use a clean cloth with a bit of ethanol and wipe it
gently. If the camera will not be used for an extended period of
time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera at the sun or extra bright places. A
blooming or smear may occur otherwise (which is not a
malfunction however), and affecting the endurance of sensor
at the same time.

High-Definition IR Water-Proof Bullet Camera·User Manual
10
10
The sensor may be burned out by a laser beam, so when any
laser equipment is being used, make sure that the surface of
the sensor will not be exposed to the laser beam.
Do not place the camera in extremely hot or cold temperatures
(the operating temperature should be between -40°C ~ 60°C ,
dusty or damp locations, and do not expose it to high
electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for a
proper operating environment.
Do not let water and any liquid flow into the camera.
While shipping, the camera should be packed in its original
packing, or packing of the same texture.
Improper use or replacement of the battery may result in
hazard of explosion. Replace with the same or equivalent type
only. Dispose of used batteries according to the instructions
provided by the battery manufacturer.

High-Definition IR Water-Proof Bullet Camera·User Manual
11
11
Table of Contents
1 Introduction................................................................ 12
1.1 Product Features ................................................12
1.2 Product Appearances ..........................................13
2 Installation ................................................................. 14
2.1 Installation ........................................................14

High-Definition IR Water-Proof Bullet Camera·User Manual
12
12
1Introduction
1.1 Product Features
This camera adopts a high-sensitivity sensor and advanced circuit
design technology. It is possessed of high resolution, low image
distortion and low noise features, which are suitable for
supervisory system and image processing system.
Adopt high-performance sensor, and with a high resolution
which brings high-quality images.
High color rendition with Auto White Balance function.
High S/N ratio which makes the image is vivid and clear.
Support Auto Electronic Shutter control to adapt to different
environments.
Support auto gain control to adapt to changing light conditions.
Support Backlight Compensation (BLC), which can adjust the
iris so that the object in the sensitive area is properly exposed.
Bullet camera adopts an advanced product design and the
mounts of them support wiring out from inside.
Adopt unique two-shell design which can ensure the senor has
a proper temperature to get a high quality image.
Ingress Protection level reaches IP66.

High-Definition IR Water-Proof Bullet Camera·User Manual
13
13
1.2 Product Appearances
Three-Axis Adjustment: the pan axis range is 0~360°, tilt axis
range is 0~75°, and the rotation axis range is 0~360°.
Bracket
Mounting Base
Power Cable
Video Cable
Zoom
Focus

2Installation
2.1 Installation
Before you start:
When mounting the camera, for the cement wall, you need to
mount the base with expansion screws. For the wooden wall, you
need to mount the base with self-tapping screws. Please ensure
that the wall is strong enough to withstand more than 3 times the
weight of the camera and the bracket. If the wall is not strong
enough, the camera may fall and cause serious damage.
Note: Before any operation, please make sure that the device in
the package is in good condition and all the assembly parts are
completed.

This series of bullet camera is equipped with installation bracket,
and usually wall installation is preferred, here we will take wall
installation as an example to explain how to install the device.
Steps:
1. Drill the holes on the wall with the supplied drilling template.
2. Route the cables inside the ceiling or on the surface. If you
want to route the cables inside the ceiling, drill the cable hole in
the ceiling for wiring; pull all cables through the hole and
terminate all wires (if not yet terminated).
3. Connect the power cable and video cable and secure the
mounting base with camera to the wall with supplied screws.
Figure 1-1 Secure the Camera
4. Three-axis adjustment.
1). Preview the image of the camera on a monitor.
Wall

Note: You must loosen the lock screw or fixed ring before
adjustment and tighten it when you adjusted it.
2). Rotate the panning table to adjust the panning position of
the camera. The adjustable range is from 0 degree to 360
degrees.
3). Rotate the tilting table to adjust the tilting position of the
camera. The adjustable range is from 0 degree to 75
degrees.
4). Rotate the lens to adjust the azimuth angle of the image.
The adjustable range is from 0 degree to 360 degrees.
Figure 2-1 Adjusting the Azimuth Angle
5. To focus and zoom, adjust the FOCUS and ZOOM screws on the
camera to get a clear image.
Pan: 0~360°
Lock screw
Lock screw
Rotation: 0~360°
Tilt: 0~90°

Figure 2-2 Adjusting the Lens
Focus
Zoom