AAXA Technologies LED PICO + User manual

aaxa
TECHNOLOGIES
User Guide
LED PICO +
Pico Projector

Caution!
WARNING: Please use this product as instructed. Misuse may cause
injury or death.
DO NOT use while driving
DO NOT expose to water or wet
surfaces. Electric shock may occur.
DO NOT expose the projected LED
image to your eyes or the eyes of
others
DO NOT block or restrict airow
from ventilation holes as this may
cause the projector to overheat
Keep the projector, battery, or
charger away from any heat sources
Caution for Battery Use
• Do not pierce or puncture the battery
with sharp objects
• Do not heat the product or expose it to
high temperature.
• Do not wet it or place it in any liquid
Caution for Headphone Use
• Prolonged use at high volume may impair
your hearing.
• High volume during walking or driving may
cause distractions and result in injury or death

Table of Contents
Chapter 1: LED Pico+ at a Glance
LED Pico+ Introduction
KeypadKeypad
Accessories
Chapter 2: Getting Started
Charging & Powering On / O󰀨
Focus Adjustment / Throw Distance
Mirroring Menu
Connecting to a Device via Digital
AV
Connecting to a Computer
Connecting to Composite Video
Connecting to Speaker or
Headphones
Connecting a TF Card
Connecting a USB Drive
Chapter 3: Menu Screens
Main Menu
Video Player Menu
Photo Menu
Chapter 4: Settings Menu
Picture Settings
Sound Settings
Option Settings
Brightness
Chapter 5: Technical Details
Frequently Asked Questions
Troubleshooting
Specications
Notes
1
2
3
4
5
6
12
14
15
17
18
20
22
23
27
32
33
34
35
36
37
38
41
42

LED Pico+ at a Glance
1
Chapter 1
Main Unit Front/Back
Power Button
Menu Navigation
Hard Reset
TF Card Slot
Focus Adjustment
USB Port
Charging Port
Audio Out
AV Input
Mini Digital
AV Port
Back/Exit

Keypad
2
Back/Exit On/O󰀨
Directional Keys

Accessories
3
* Under various circumstances, the actual accessories may be di󰀨erent from
those shown in the pictures above.
Tripod USB-C Charge Cable
HDMI to Mini HDMI Cable AV Cable

Getting Started
1. To power-on a fully charged LED Pico+, hold down the power button for approxi-
mately three seconds until the projector turns on.
4
Powering ON the projector
Chapter 2
Powering OFF the projector
1. Press the power button once, then again to conrm.
2. After a few seconds, the unit should completely turn o󰀨.
1. Turn the LED Pico+ Projector completely o󰀨 before charging.
2. Connect the USB-C end of the included Charge Cable to the DC port of the LED
Pico+ Projector.
3. Connect the USB end of the included Charge Cable to a power source. For continu-
ous operation, a USB charger with 5V/2A output is required.
Charging the projector
NOTE: The LED Pico+’s battery does not charge when it is in operation.

Focus Adjusment / Throw Distance
5
DIAGONAL SCREEN SIZE
16:9 Aspect Ratio
Throw Distance
Units: Inches
20
30
40
50
60
Diagonal Size
Units: Inches
12
18
25
31
37
• Spin the focus wheel up or down until the image becomes
clear.
Focus Adjustment
Throw Distance Chart
Throw Ratio 1.9
Projection Angle: 0% O󰀨set
*minimum throw distance: 10 inches

6
Mirroring Menu
• The LED Pico+ allows for
wireless mirroring and projection
of smartphone content including
pictures, videos, and other on-
screen media. The wireless
mirroring function works through a
direct wireless connection and is
compatible with smartphones that
provide this feature.
• This includes most Samsung/
Android compatible smartphones
and most Apple/iPhone compatible
smartphones. If you are unsure
whether this feature exists in your
smartphone, please check with the
manufacturer.
• NOTE: Copyright content such as
Netix, Amazon Prime, HBO, etc.
content cannot be mirrored.

Mirroring Menu
7
To Wirelessly Mirror your smart device
1. In the Main Menu, select the Mirroring icon.
2. In the Mirroring submenu, select your smart device manufacturer (iPhone
compatible or Android compatible).

8
Direct Mirroring for Android Compatible Devices
• Once the Mirroring Menu appears, select the mirroring feature in your smart
device.
• For Samsung phones this is often the “Smart View” icon. (g. 2.1)
• The Smart View icon can typically be found by swiping down on the settings
menu and selecting the icon; or it can be found through a features search.
• Click on the “Smartview” icon – this will allow your smart device to search for
the LED Pico+. (g. 2.2)
• Select “AAXA-PICOPLUS” as the device. The screen should automatically
begin to mirror upon connection.
g. 2.1 g. 2.2

Direct Mirroring For iPhone Compatible Devices
9
• Enter the “iPhone Compatible” mirroring submenu
• Go to your iPhone settings, Select Wireless Connections (g. 2.3)
• Select “AAXA-PICOPLUS” as a wireless connection (g. 2.4)
g. 2.3 g. 2.4

10
Direct Mirroring For iPhone Compatible Devices
• The password should be “12345678”.
• In your iPhone’s “Screen Mirroring” menu, select AAXA-PICOPLUS
(g. 2.5). The Screen Mirroring Menu can typically be found by swiping
down from the Home screen.
• Tap “Stop Mirroring” when you wish to stop mirroring your iPhone.
g. 2.5

11
Screen Mirroring FAQ
Q: Why can’t I see Netix, Hulu, Amazon Prime, etc. content?
A: Content copyright under DMCA cannot be displayed via wireless screen
mirroring.
Q: Can I use wired mirroring instead of wireless mirroring for
iPhones?
A: The LED Pico+ is compatible with wired mirroring through Apple’s pro-
prietary Lightning to HDMI adapter. This can be purchased from an autho-
rized Apple Retailer.
Note: Samsung is a trademark of Samsung Group and iPhone is a trade-
mark of Apple inc. AAXA Technologies Inc claims no rights.

Connecting to a Device via Digital AV
12
The LED Pico+ has a mini-Digital AV port. A Digital AV cable is required to connect
your LED Pico+ to Digital AV compatible devices.
In the Main Menu
Select “INPUTS” icon Select “DIGITAL” icon
Connectivity to Multimedia Devices
The LED Pico+ can connect to many media devices including: computers, laptops,
iPhones, iPads, DVD players, smart phones, cameras, video game consoles and
other peripherals with ease.
*Some smartphones and tablets require video out capabilities to be displayed with the LED Pico+.
Check with the manufacturer.

Connecting to a Device via Digital AV (Cont)
13
Connect one end of the mini-Digital AV Cable to
your device’s Digital AV port.
Step 1:
Step 2:
Step 3:
In the Main Menu, select the “INPUTS” icon and then the “DIGITAL” icon, as
shown on page 12. Your LED Pico+ should now be displaying the content
from your device.
Connect the other end of the mini-Digital AV Cable
to your LED Pico+’s Video In port.
If you’re connecting to a computer or laptop and the projector does not
automatically mirror it, read onto the next page for more information.
Note:

Connecting to a Computer
Step 4:
Enabling Digital Video output on your Computer – To enable Digital Video output on your computer
most computers require “turning on” the video output feature. Each computer is di󰀨erent. Please
consult your owner’s manual for instructions to enable Digital Video output. Below are standard
instructions for a Windows 10 computer – not all systems are the same.
Press Windows+P to toggle
through display settings. Select
either “Duplicate” or “Extend” de-
pending on your viewing option.
*NOTE: dierent operating sys-
tems may dier
Step 5:
1. Right click on com-
puter desktop and select
“Screen Resolution”
2. Display Properties win-
dow will pop up
3. If a secondary monitor
is grayed out, click on it
and select “Extend these
displays” in the “Multiple
Displays” drop down
4. If the image is blurry or
the text is not legible,
adjust the screen resolu-
tion. We recommend
1280x720.
14
Step 6:

Connecting to Composite Video
15
Connect the 3.5mm Composite AV
Cable to the AV Port of the LED Pico+.
Plug the composite end of
the AV Cable (Red, White,Yellow)
to your device.
Step 1:
Step 2:

Connecting to Composite Video Cont.
Connectivity with multimedia devices
The LED Pico+ can connect to many media devices including: DVD players, Blu-
Ray players, smartphones, cameras, video game consoles and other peripherals
with ease.
*Some smart phones require video out capabilities to be displayed with the LED Pico+.
Check with your phone manufacturer. 16
In the Main Menu
Turn on your multimedia device. If available, select 1280x720 or 1920x1080.
Select “INPUTS” icon Select “AV” icon
Step 3:
Step 4:

Connecting to Speakers / Headphones
17
Connect your speaker/headphones to
the projector’s audio port.
Step 1:
Step 2:
*CAUTION: Prolonged use of headphones at a high
volume may impair hearing.
Ensure that the projector and/or the
headphones are powered on.
Step 3: Place the headphones on and enjoy!