AAXA Technologies M6 User manual

aaxa
TECHNOLOGIES
User Guide

Caution!
WARNING: Please use this product as instructed. Misuse may cause
injury or death.
DO NOT use while driving
DO NOT expose to water or wet
surfaces. Electric shock may occur
DO NOT expose the projected LED
image to your eyes or the eyes of
others
DO NOT block or restrict airow
from ventilation holes as this may
cause the projector to overheat
Keep the projector, battery, or
charger away from any heat sources
Caution for Battery Use
• Do not pierce or puncture the battery
with sharp objects
• Do not heat the product or expose it to
high temperature.
• Do not wet it or place it in any liquid
Caution for Headphone Use
• Prolonged use at high volume may impair your
hearing.
• High volume during walking or driving may
cause distractions and result in injury or death

Table of Contents
Chapter 1: M6 at a Glance
M6 Introduction
Remote & Keypad
Accessories
Chapter 2: Getting Started
Powering On / Off
Focus Adjustment / Throw
Distance
External Input/Outputs
Connecting to a Computer VGA
Connecting to a Digital Input
Connecting to Composite Video
Connecting to Digital Input Video
Connecting to Speaker or
Headphones
Connecting a TF Card
Connecting a USB Stick
Chapter 3: Menu Screens
Main Menu
Video Player Menu
Photo Viewer Menu
Music Player Menu
Text Viewer Menu
Chapter 4: Setup Menu
Settings
Brightness Feature
Chapter 5: Technical Details
Troubleshooting
Specications
Notes
1
2
3
4
5
6
7
9
11
13
15
16
18
20
21
25
29
32
33
37
38
40
41

M6 at a Glance
1
Chapter 1
Power Switch
TF Card
Digital Input
USB Port
Main Unit Front/Back
VGA Port
Power Button
Focus Adjustment
AV Port
Headphone Out
Power On/Off
DC Port
Infrared Receiver
(Remote Control)

Remote & Keypad
2
NOTE: Pressing power on the remote will only put the projector in STANDBY mode.
Toggle the “ON/OFF” switch on the side of the projector to fully turn the projector off.
Power On/Off Mute
Input Exit/Back
Direction Pad
Both the keypad and remote can be used to navigate through the menus. The Main Menu
Navigation on the remote functions exactly the same as the directional pad on the M6 unit.
On / Off
LED Lights
OK
Main Menu
Navigation
Media Player
Menu Navigation
Volume Up
Volume Down
Remote
*Keystone function is not available.
Home
Back

Accessories
3
*Under various circumstances, the actual accessories may be different from
those shown in the pictures above.
Additional accessories are available for purchase at www.aaxatech.com
Remote
Power Adapter
A/V Cable
Carrying Case

Getting Started
1. Connect the power cord to the M6.
2. Connect the other end of the power cord into the wall power source.
3. Toggle the On / Off switch on the side of the projector to the “ON” position -- the
projector should automatically turn on.
4. If the projector does not automatically turn on with the “Power Switch” toggled to the
“ON” position, press the “ON/OFF POWER” button on the keypad and hold for
2-3 seconds to start the projector.
4
Powering ON the projector
Chapter 2
Powering OFF the projector
Standby Mode
1. To transition to “STANDBY” mode, press the power button on the keypad or the
remote control.
2. The optical engine should power off and the fan should stop spinning. The projector
is now in “STANDBY” mode and can be turned on using the remote control.
*Note: Standby mode will still consume a small amount of power.
1. To turn off the projector, toggle the “Power Switch” to the “OFF” position. This will
fully turn off the projector.

Focus Adjusment / Throw Distance
5
DIAGONAL SCREEN SIZE
16:9 Aspect Ratio
Throw Distance
Units: Inches
19
38
58
77
96
115
153
192
Diagonal Size
Units: Inches
20
40
60
80
100
120
160
200
• Spin the focus wheel up or down until the image becomes
clear.
Focus Adjustment
Throw Distance Chart
Throw Ratio 1.10
Projection Angle: 100% Offset
*minimum throw distance: 12 inches

6
External Inputs and Outputs
Headphones/speakers
Composite Cable
Digital Input
VGA
USB Stick
TF Card

Connecting to a Computer via VGA
7
Connect one end of the VGA Cable
to your computer’s VGA Adapter.
Step 1:
Step 2:
Step 3:
In the Main Menu, select the “Inputs” icon and then the “VGA” Icon.
Connect the other end of the VGA
Cable to your M6’s VGA port.
Select “VGA” iconSelect “INPUT” icon