ABB ACS580-01 +C135 Series User manual

1
ACS580-01…+C135, ACH580-01…+C135 and ACQ580-01…+C135 frames R4 and R5 flange mounting kit quick installation guide
4 × M5×20 screw
16 × M6×25 screw
23 × M6 nut
2 × M4 nut
f
h
i
4×M6nut
6 N·m (4.4 lbf·ft)
Note: First attach the inner sides of
the brackets (1) that touch the drive,
then the outer sides (2).
Note: Attach this end to the
bottom U-bracket to make
sure that the sealing is tight.
4 × M5×20 screw
3 N·m
8×M6nut
6 N·m (4.4 lbf·ft)
R4 IP21 (UL Type 1)
only
For IP55 (UL Type
12) the plug is
installed at the
factory.
a
ABB parts
Available as option +C135 and separately with ordering codes:
3AXD50000031460 (R4) and 3AXD50000031461 (R5).
e
d
4
1
5
23
Note: Wear protective
gloves when working.
a
b
8×M6nut
6 N·m (4.4 lbf·ft)
b
c
e
e
d
d
g
f
1
2
1
2
fg
fg
g
c
Frame R5 onlyFrames R4 and R5
Remove the tightening bracket from
the front of the fan.
Attach the clamp plate.
2 × M4 nut, 1 N·m(0.7 lbf·ft)

ACS580-01…+C135, ACH580-01…+C135 and ACQ580-01…+C135 frames R4 and R5 flange mounting kit quick installation guide 2
13
6Drill holes for M6 Rivet or Kalei nuts. Consider the hole size for the nuts.
Rivet/Kalei nuts are not included in the delivery.
Note: The mounting templates are different (size, number and position of
holes) for different frame sizes.
3 x M6 nuts
6 N·m (4.4 lbf·ft)
ACQ580-01 manuals
ACH580-01 manuals
ACS580-01 manuals
For dimensions, see the mounting
template delivered with the flange
mounting kit or ACS580-
01…+C135, ACH580-01…+C135 and
ACQ580-01…+C135 drives with
flange mounting kit supplement
(3AXD50000349821 [English]).
Go to www.abb.com/drives.
UL Type 12 only
UL Type 12 is fulfilled on the drive backside when the flange and hood
are installed. Hood is not required for IP55.
FrontBack
Hood (view from top)
Hood (view from
bottom)
9
8
h
1 × M6×25 screw
6 N·m (4.4 lbf·ft)
1 4 × M6×25 screw
6 N·m (4.4 lbf·ft)
i
11 12
R4 IP21 (UL Type 1) only
Remove the control panel (a) and cover (b) to install the auxiliary fan (ordering code
3AXD50000034334). Cut off the protective plate from the fan slot (c) and install the fan
(d). Make sure that the arrow on the fan points outwards. Connect the fan cable to FAN2.
1 × M6×25 screw
6 N·m (4.4 lbf·ft)
7
10
f
a
b
c
e
d
R4: X6
3AXD50000287093 Rev C (EN) 2022-21-06 © Copyright 2022 ABB. All rights reserved. Specifications subject to change without notice.