Above All FSP-211 User manual

Programmable Multi-Level Motion Sensor
Instruction Manual
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.aboveallLighting.com ©2016 ABOVE ALL. Inc. All rights reserved
SUITABLE FOR MODEL
IMAGE MAY VARY FROM ACTUAL PRODUCT
The FSP-211 is a passive infrared (PIR) outdoor sensor that raises or lowers the electric lighting level to high, low or
off based on motion and/or daylight contribution. Typically, once the sensor stops detecting movement and the time
delay elapses, lights will rst fade to low mode, and eventually switch off. When motion is detected, the sensor ramps
the light level to high mode unless the daylight contribution is sufcient. The integral photocell can also switch the
lights on and off for dusk to dawn control, so that lighting remains on overnight even without motion detection.This
slim, low-prole sensor is designed for installation inside the bottom of a light xture body, and is rated for wet and
cold locations.Initial setup and subsequent sensor adjustments are made using a wireless handheld conguration tool
(FSIR- 100). This tool enables adjustment of sensor parameters including high/low mode, sensitivity, time delay, cut
off and more.
The FSIR-100 can read current parameter settings, and stores up to six sensor parameter proles to speed
commissioning of multiple sensors. (NOTED: FSIR-100 NEEDS TO BUY SEPARATELY WHICH IS NOT
CONTAINED IN MULTI-LEVEL MOTION SENSOR PROVIDED BY ABOVE ALL)
DESCRIPTION
DESCRIPTION
FSP-211 SENSOR MODULE FSP-211 DIMENSIONS
1.66”
42.18mm
1.63”
41.28mm
1.29”
32.77mm
Threaded Collar
Rubber Gasket
Nut
Lens
3.79”
96.27mm
1.38”
35.05mm
0.9”
22.86mm
0.65”
16.48mm

Programmable Multi-Level Motion Sensor
Instruction Manual
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.aboveallLighting.com ©2016 ABOVE ALL. Inc. All rights reserved
ABOVE ALL STANDARD PROGRAMMABLE MULTILEVEL MOTION SENSOR
FSP211+FSP L7
Outdoor installation using Setpoint and Photocell features (Above All Default Settings)
High Mode .................................................................
Low Mode ....................................................................
Time Delay ..................................................................
Cut Off ..............................................................................
Sensitivity ........................................................................
Setpoint ..............................................................................
Ramp Up ...........................................................................
Fade Down ........................................................................
Photocell ............................................................................
10 Volts
3 Volts
15 min
Dis
Max
15
Dis
Dis
30
This conguration will set the luminaire to turn on at dusk when the ambient light level drops below 15 fc (161 lx). When
motion is detected, the luminaire will switch to high mode. If after 15 minutes no motion is detected, then it will switch
to low mode. If the ambient light level is greater than 15 fc but less than 30 fc (322 lx), then the luminaire will stay in
low mode, even if motion is detected. When the ambient light level rises above 30 fc, then the luminaire will turn off and
remain off until the light level drops back below 15 fc.
Tip: It may be necessary to adjust the setpoint and photocell values to compensate for reected light from the luminaire
or adjacent lightsources. Check the light level by reading the current settings using the programming tool. If the light level
is higher than the photocell value, the luminaire will turn off. If this behavior is not desired, then increase the photocell
value. If the luminaire is staying in low mode, then it may be necessary to increase the setpoint value.
Tip: When checking light level, wait ~5 seconds after a sudden change in light level (e.g. luminaire switching from high to
low mode). It may be necessary to take more than one reading.

Programmable Multi-Level Motion Sensor
Instruction Manual
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.aboveallLighting.com ©2016 ABOVE ALL. Inc. All rights reserved
Indoor installation using Setpoint and Photocell features(Above All Default Settings)
High Mode .................................................................
Low Mode ................................................................
Time Delay ....................................................................
Cut Off ...........................................................................
Sensitivity .......................................................................
Setpoint .............................................................................
Ramp Up ...........................................................................
Fade Down ....................................................................
Photocell ............................................................................
10 Volts
5.0 Volts
2 min
5 min
High
Dis
Dis
5 sec
Dis
In this conguration the luminaire dim to low mode with a 5-second fade down after 2 minutes elapse with no motion
detection. After 5 minutes, the luminaire will turn off. When motion is detected, the luminaire will switch to high mode. The
luminaire will not be affected by the ambient light level.
COVERAGE
FSP-L2 top and side
coverage patterns
FSP-L3 top and side
coverage patterns
FSP-L4 top and side
coverage patterns

Programmable Multi-Level Motion Sensor
Instruction Manual
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.aboveallLighting.com ©2016 ABOVE ALL. Inc. All rights reserved
FSP-L7 top and side
coverage patterns
Above All standard one: FSP-L7
Customers need another coverage lens should be ordered separately.
WIRE CONNECTION
CUSTOMER SETTING GUIDANCE
USING THE FSIR-100
The FSIR-100 is a convenient handheld remote tool for setting up the
FSP-211.
Adjustable settings can be changed as needed for specic applications.
Wiring Diagram For Typical Driver Wiring Diagram For Meanwell Driver
Power
On/Off
Back
Left
Down
Home/Main Menu
Up
Right/Next
Select

Programmable Multi-Level Motion Sensor
Instruction Manual
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.aboveallLighting.com ©2016 ABOVE ALL. Inc. All rights reserved
High Mode: When the sensor detects motion the dimming control output ramps up to the
selected HIGH light level.
1.
Low Mode: After the sensor stops detecting motion and the time delay expires the dimming
control output fades down to the selected LOW light level.
2.
Time Delay: The selected time period that must elapse after the last time the sensor detects
motion for the electric lights to fade to LOW mode.
3.
High Mode: When the sensor detects motion the dimming control output ramps up to the
selected HIGH light level.
4.
Sensitivity: The response of the PIR detector to motion within the sensor’s coverage area.5.
Setpoint: When enabled, the selectable ambient light level threshold that will hold the electric
lights off or at LOW level when the sensor detects motion.
The Auto option invokes an automatic calibration procedure to establish an appropriate
setpoint based upon the contribution of the electric light. As part of this procedure, the
controlled load is turned on for two minutes to warm up the lamp, and then switched off
and on eight times, terminating in an off state. After this process, a new setpoint value is
automatically calculated.
6.
Photocell On/Off: When enabled, the sensor will force the load OFF after the light level has
exceeded the selected photocell setpoint for at least a minute. It will also force the load ON
when the light level goes below the setpoint, even if no motion is detected.
Once ON (initially at High), the load will dim to Low following the Time Delay, and to OFF
following the Cut Off time. To ensure dusk to dawn control, Cut Off must be disabled.
The photocell On/Off setpoint is automatically set to maintain a deadband of at least 10 fc
above the Hold Off Setpoint to prevent cycling if the two features are used together.
7.
Ramp Up Time: Time period for light level to increase from LOW to HIGH.8.
Fade Down Time: Time period for light level to decrease from HIGH to LOW.9.

Programmable Multi-Level Motion Sensor
Instruction Manual
Add: 1501 Industrial Way N, Toms River, NJ 08755 Phone: [phone] E-mail: [email protected]
Web: www.aboveallLighting.com ©2016 ABOVE ALL. Inc. All rights reserved
Ref#: 21104
Lock Settings: Time delayed IR communication lock initiated from the FSIR-100 to prevent
unauthorized changes of FSP-211 parameters until power is cycled to the sensor.
To lock settings, select Lock Delay, set a time, and press SEND to send the parameter
change to FSP-211. After the countdown, FSP-211 will no longer respond to the FSIR-100.
If additional conguration is required, cycle the power to the FSP-211 off and then back on.
To disable the lock parameter after the power cycle, select Lock Delay, select Disable, and
press SEND.
10.
Troubleshooting
Lights that shine or reect into photocell may turn off the xtures.
1) Adjust the motion sensor counterclockwise or clockwise to avoid light or reected lights
2) Increase the “Photocell Set point for On/Off ” , e.g. increase 5 fc.
Warranty
Five year limited warranty. Full warranty terms located at www.abovealllighting.com/warrantystatements