AC Infinity CLOUDFORGE T3 User manual

1
USER MANUAL
CLOUDFORGE
ENVIRONMENTAL HUMIDIFIER

3
WELCOME
Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service.
If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com
and click contact for our contact information.
EMAIL
[e-mail]
WEB
www.acinfinity.com
LOCATION
Los Angeles, CA

4
MANUAL CODE CF2207X1
MODEL
AC-CFT3
AC-CFT5
AC-CFT7
AC-CFT9
PRODUCT
CLOUDFORGE T3
CLOUDFORGE T5
CLOUDFORGE T7
CLOUDFORGE T9
UPC-A
819137023611
819137023635
819137023628
819137023642

5
MANUAL INDEX
Manual Index .................................................................................
Product Warning ............................................................................
Key Features .................................................................................
Product Contents ...........................................................................
Installation .....................................................................................
Powering and Setup ......................................................................
Universal Infinity SystemTM ............................................................
Connecting to UIS™ Controllers ...................................................
Cleaning ........................................................................................
Programming .................................................................................
Other Settings ................................................................................
Other AC Infinity Products .............................................................
Warranty ........................................................................................
Page 5
Page 6
Page 7
Page 8
Page 9
Page 14
Page 18
Page 19
Page 20
Page 22
Page 26
Page 27
Page 28

6
Ensure your power source conforms to the electrical requirements of this product.
Read all instructions before installing and using this product.
Do not attempt to hardwire this product. Performing any retrofitting actions may result in
personal injury and/or electrical damage, and will void this product's warranty.
Be careful not to damage or cut the wire insulation (covering) during the installation. Do not
permit wires to come in contact with any sharp edges.
This product must not be used in potentially hazardous locations such as flammable,
explosive, or chemical-laden atmospheres.
Do not cover any power cords with rugs or other fabric materials.
Safety precautions should be exercised during the installation, operation, and maintenance of
this product.
Do not block or tamper with this product in any manner while it is in operation as it may cause
electric shock, fire, or damage to this product.
Do not depend on the on/off programming as the sole means of shutting power from this
product. Unplug the power cord before installing, servicing, or moving this product.
Do not operate this product while its cord is damaged, or if it malfunctions, has been dropped,
or is damaged in any manner.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
PRODUCT WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:

7
KEY FEATURES
TARGETED ZONE
Includes a directional cap and
stretchable tube, or pipe and
nozzles, for various humidity
distribution methods in spaces like
grow tents, DIY grow rooms, living
spaces, and greenhouses.
SMART CONTROLLER
Onboard controller with LED touch
interface featuring humidity balance
programming. Pair with UIS controllers
to access intelligent programming and
app control with advance automation
and data charts.
PRECISION DETECTION
Swiss-made thermal alloy sensor
made of SAE grade-316 steel detects
humidity changes and provides up-to-
the-minute readings. Extension cord
enables detection in spot areas and
convenient humidifier placement.

8
CLOUDFORGE T3
PROBE
MOUNT
(x1)
NEBULIZER
BRUSH
(x1)
UIS EXTENSION
CORD (M-M)
(x1)
HOOK AND
LOOP TIE
(x1)
PRODUCT CONTENTS
4.5L
HUMIDIFIER
(x1)
FLEXIBLE
HOSE
(x1)
CLOUDFORGE T7
15L
HUMIDIFIER
(x1)
ALL MODELS
SENSOR
PROBE
(x1)
PIPE
BASE
(x1)
ELBOW
NOZZLE
(x1)
5-WAY
NOZZLE
(x1)
ELASTIC
BANDS
(x4)
PVC
PIPE
(x1)

9
INSTALLATION
CLOUDFORGE T3
STEP 1
Add water into the tank.You may detach the
tank to fill it with water.
We recommend using distilled water to reduce
the amount of mineral build-up.
B
NOTE: Do NOT pour water into the central pipe. This will prevent your
humidifier from functioning properly.
A

10
INSTALLATION
CLOUDFORGE T3
STEP 2
You may swap the directional flow cap with the
included flexible hose for extended targeted flow.
A
B

11
INSTALLATION
CLOUDFORGE T7
STEP 1
Add water into the tank.You may detach the
tank to fill it with water.
We recommend using distilled water to reduce
the amount of mineral build-up.
BA
NOTE: Do NOT pour water into the central pipe. This will prevent your
humidifier from functioning properly.

12
INSTALLATION
CLOUDFORGE T7
STEP 2
Top the center lid opening with the included base.
Attach the pipe onto the base, followed by your
choice of nozzle:
A. Elbow nozzle* for unidirectional flow
B. 5-way nozzle for omnidirectional flow
AB
*Make sure the elbow nozzle is placed over the pipe with the interior ridge
facing the ground.

13
INSTALLATION
CLOUDFORGE T7
STEP 3
You may use your own PVC pipes to extend the
reach of your humidifier.
Line the pipe with the included elastic band and
attach it to the base or elbow nozzle.
A B

14
POWERING AND SETUP
CLOUDFORGE T3
STEP 1
Plug the sensor probe into the 3.5mm jack
located at the rear side.
Route the probe head to spot areas as needed.

15
POWERING AND SETUP
CLOUDFORGE T3
STEP 2
You may plug the included UIS extension cord
into the rear side port to connect your humidifier
to your UIS controller.
STEP 3
Plug the humidifier's power plug into an outlet
to power it.

16
POWERING AND SETUP
CLOUDFORGE T7
STEP 1
Plug the sensor probe into the 3.5mm jack
located below the display screen.
Route the probe head to spot areas as needed.
You may also use the included probe mount to
cable manage the corded probe.

17
POWERING AND SETUP
CLOUDFORGE T7
STEP 3
Plug the humidifier's power plug into an outlet
to power it.
STEP 2
You may plug the included UIS extension
cord into the front side port to connect your
humidifier to your UIS controller.

18
UNIVERSAL INFINITY SYSTEMTM
AN INTERCONNECTED GROW SETUP
The Universal Infinity System is a series of controllers and devices that come together to create a
fully automated system. UIS enables our controllers to simultaneously connect with various grow
equipment such as inline fans, clip-on fans, and grow lights. Advance UIS controllers can provide
each connected UIS device with their own automated programming like temperature, humidity,
cycles, schedules, and dynamic levels, while also pairing with the AC Infinity app.
Central controllers and grow devices will be sold separately and may still be in development
at the time of your purchase of this product.

19
CONNECTING TO UISTM
EXTENSION CABLE
Use the included UIS M-M extension cord to connect
the humidifier to your CONTROLLER 69 unit.
Your CONTROLLER 69 unit will override all onboard
settings and assume control (parameters must be
adjusted on CONTROLLER 69) when connected in
this manner. The humidifier's touch functions will also
be deactivated.
CLOUDFORGE humidifiers can connect with CONTROLLER 69 (sold
separately) as part of an integrated system using the included UIS
extension cord.

20
CLEANING
STEP 1
Unplug your humidifier and remove the tank
from the base.
STEP 2
Pour out any water sitting in the base. Pour two
cups of distilled water and one tablespoon of
vinegar into the base. Let it sit for five minutes.
+
2
Change water reservoir at least once every 4 days. Clean and maintain the unit at least once per week.
VINEGAR