Access Atr110 User manual

Access-IS

18 Suttons Business Park, Reading

Berkshire, RG6 1AZ, United Kingdom

Tel: +44 (0) 118 966 3333

Web: www.access-is.com

Email: [email protected]

Product names

mentioned herein are for

identification purposes

only and may be

trademarks and/or

registered trademarks of

their respective

companies.

ALL RIGHTS

RESERVED

Subject: ATR110 Manual

Revision: 1.4

Issue Date: 15/03/2016

ATR110

1D/2D Barcode Imager

(Barcode Only Version)

Product Manual

Warnings

This manual contains important information regarding the installation and operation of the ATR110 1D/2D

Barcode Imager. For safe and reliable operation of the imager, installers must ensure that they are familiar

with and fully understand all instructions contained herein.

Warranty

Access Ltd warrants that this product shall be free from defects in workmanship and materials for a period of

one year from the date of original purchase. If the product should fail to operate correctly in normal use during

the warranty period, Access will replace or repair it free of charge. No liability can be accepted for damage

due to misuse or circumstances outside Access’control. Access will not be responsible for any loss, damage

or injury arising directly or indirectly from the use of this product. Access’total liability under the terms of this

warranty shall in all circumstances be limited to the replacement value of this product.

Radio Frequency Energy

European EMC directive 89/336/EEC

This equipment has been tested and found to comply with the limits for a class A computing

device in accordance with the specifications in the European standard EN 55022. These

limits are designed to provide reasonable protection against harmful interference. This

equipment generates, uses and can radiate radio frequency energy and if not installed and

used in accordance with the instructions may cause harmful interference to radio or

television reception. However, there is no guarantee that harmful interference will not occur in a particular

installation. If this equipment does cause interference to radio or television reception, which can be

determined by turning the equipment on and off, the user is encouraged to correct the interference with one or

more of the following measures: (a) Reorient or relocate the receiving antenna. (b) Increase the separation

between the equipment and the receiver. (c) Connect the equipment to an outlet on a circuit different from that

to which the receiver is connected. (d) Consult the supplier or an experienced radio / TV technician for help.

FCC Compliance Statement (United States)

This equipment generates, uses and can radiate radio frequency energy and if not installed and used

properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio

communication. It has been tested and found to comply with the limits for a class A computing device in

accordance with the specifications in Subpart J of part 15 of FCC rules, which are designed to provide

reasonable protection against such interference when the equipment is operated in a commercial

environment. Operation of this equipment in a residential area may cause interference, in which case the user

at his own expense will be required to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the manufacturer could void the user’s authority to

operate the equipment.

Canadian Department of Communications RFI statement

This equipment does not exceed the class A limits for radio noise emissions from digital apparatus set out in

the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux

appareils numériques de la classe A prescrites dans le règlement sur le brouillage radioélectriques publié par

le ministère des Communications du Canada.

Contents

1. Overview....................................................................................................................4

2. Specifications.............................................................................................................5

2.1 Part numbers............................................................................................................... 5

3. Installation..................................................................................................................6

3.1 Unpack the ATR110.................................................................................................... 6

3.2 Connection.................................................................................................................. 6

3.3 Mounting ..................................................................................................................... 7

3.4 Interface options.......................................................................................................... 9

3.5 Serial installation....................................................................................................... 10

3.6 USB installation......................................................................................................... 10

3.7 Test the device.......................................................................................................... 11

3.8 Configuration software.............................................................................................. 11

3.9 Troubleshooting ........................................................................................................ 11

3.10 Maintenance.............................................................................................................. 11

4. Operating modes.....................................................................................................12

4.1 Mode summary ......................................................................................................... 12

4.2 Dumb mode............................................................................................................... 13

4.3 Host mode................................................................................................................. 14

4.4 Interactive mode........................................................................................................ 16

5. Command reference................................................................................................18

5.1 Basic configuration.................................................................................................... 19

5.2 Prefix and suffix solutions ......................................................................................... 20

5.3 ATR110 illumination.................................................................................................. 21

5.4 Indicator control......................................................................................................... 23

5.5 Development commands .......................................................................................... 28

5.6 Triggering.................................................................................................................. 30

5.7 Counter ..................................................................................................................... 31

A. HID reports ..............................................................................................................32

A.1 Receive data............................................................................................................. 32

A.2 Send commands....................................................................................................... 33

A.3 Trigger controls......................................................................................................... 34

B. ASCII character reference .......................................................................................35

C. Document history.....................................................................................................39

Figure 1. ATR110 1D/2D Barcode Imager

1. Overview

The ATR110 is a compact and fast barcode reader, which can process a wide range of electronic

ticketing across a variety of media.

The device reads all popular linear, PDF417 and 2D barcode symbologies, including QR and Aztec

codes, from smartphones, tablets and printed-paper documents.

The ATR110’s advanced recognition barcode imager is omnidirectional and has near-zero latency.

It captures barcodes within a fraction of a second of presentation in any orientation.

This responsive, intuitive-to-use device is simple to operate by untrained members of the public.

Additional user-friendly features include bright LED visual indicators and a programmable audio

buzzer to confirm successful data capture.

Its rugged, vibration and shock resistant construction, with no moving parts, enables the reader to

withstand years of frontline, public use.

Fast, intuitive imager with fixed focal

distance.

Reads barcodes on facedown

presentation of mobile device.

Reads 2D, PDF417 and linear barcode

symbologies.

RS232 and USB (custom human interface

device (HID), keyboard or

communications device class (CDC)

serial) interface options.

Configurable LED (green, amber, red,

blue) and audible read confirmation.

Mounting options: desktop, console,

pole-mount and fixed-position installation.

Protective rubber bumper to prevent

damage to smartphones when placed

against the unit’s toughened glass.

Designed for a wide range of applications, including public transportation.

2. Specifications

Specification

Details

Dimensions (L x W x H)

120.6 mm x 96.0 mm x 81.2 mm

Weight

443 g (with cable)

Environmental

Operating temperature: -25ºC to 50ºC

Storage temperature: -30ºC to 70ºC

Humidity: 95% non-condensing

Designed to meet IP54

Body

Dark grey ABS with blue rubber smartphone bumper

Glass

3 mm thermally toughened low-iron Conturan IK07 (3 times 2J

impact), anti-reflective coating

Buzzer

Loud (75 dBa at 1 m); volume controllable (configuration

setting - can be adjusted by customer)

Indicator LEDs

Four colours (green/amber/red/blue) (configuration setting - can

be adjusted by customer)

Power requirements

5 V DC

Electrical interface

Serial (RS232C) and 5 V USB

Barcode reading

Linear: EAN/UPC, Code 2 of 5, Interleaved 2 of 5, IATA 2 of 5,

Code 39, Code 128

2D: IATA resolution 792, PDF417, Aztec, DataMatrix and QR

codes

Media supported

Reads barcodes from mobile phones, tablets and paper

MTBF

85,000 hours

Approvals

CE EMC Class B

EN 55022

EN 55024

CE Low Voltage Directive

EN 60950-1

IEC 60825-1 LED Safety Class 1

FCC 47CFR Part 15 Subpart B Class A

2.1 Part numbers

Product

Part Number

Barcode only, serial connected ATR110

AKEGEOTB011

USB power injector cable

5KBD133402

Barcode only, USB connected ATR110

AKEGEOTA851

Pole mount - 1.25 inches (31.75 mm) pole diameter

AKEGEOXB081

Pole mount - 1.5 inches (38.1 mm) pole diameter

AKEGEOXB091

An external power supply is available, if required.

Please contact the Access-IS sales team: [email protected].

3. Installation

3.1 Unpack the ATR110

Unpack the ATR110 and ensure that you have the following items:

Advisory notice card.

ATR110 device with attached serial or USB cable.

Serial unit: USB power injector cable or power supply (IEC cable not supplied).

Report any missing items or damage immediately to your Sales Representative.

3.2 Connection

Connect the ATR110 directly to an RS232 port or USB port depending on the product version.

Note: The cable is sealed into the unit to prevent entry of water, moisture and dust. Standard

supplied cable length is 1.8 m. Other options are available for pole mounting, see page 8.

3.2.1 Connection to RS232

Figure 2. Connection to RS232

3.2.2 Connection to a USB port

Figure 3. Connection to USB

The ATR110 USB obtains power from the USB port.

To a USB port on the host PC

USB cable connected to ATR110 device

Serial and power cable connected to ATR110 device

USB power injector cable to a powered USB port

on host PC (or connection to an external power

supply)

To a COM port on the host PC

3.3 Mounting

The ATR110 is simple to install. Mounting options include desktop, console, kiosk or pole-mount.

Refer to Figure 4 for the dimensions of the unit. Figure 5 shows the mounting points.

For optimum performance, do not position the ATR110 in direct sunlight.

Figure 4. ATR110 dimensions (rounded to the nearest millimetre)

3.3.1 Mounting points

Figure 5. ATR110 mounting points

Use four M3 screws (not provided) to mount the unit. Maximum insertion depth is 4 mm; minimum

recommended insertion depth is 2 mm.

Figure 6. Pole-mount cable connection

3.3.2 Pole mounting

An optional pole-mount kit allows you to mount the device on a 1.25 inch or 1.5 inch diameter pole.

If the mounting bracket is pre-fitted to the unit, attach the unit to the pole as follows:

1. Remove the two M3 screws holding the plastic

back cover in place on the ATR110.

2. Unscrew the four M4 screws holding the two

metal ‘U’ brackets together.

3. Wrap the drilling template around the pole and

drill the holes into the pole. Drill the smaller

holes (6 mm) all the way through the pole; drill

the larger hole (24 mm) on the front face of the

pole only.

4. Feed the cable through the larger hole in the

pole and screw the main cable to the cable

attached to the device.

5. Make the appropriate cable connections to the

host, depending on whether you are fitting a

USB or Serial device.

6. Position the ATR110 on the pole ensuring that

the locating studs on the metal ‘U’ brackets

engage in the two smaller holes in the pole.

Position the other metal ‘U’ bracket against the

back of the pole and screw the metal brackets

together using the four M4 screws removed

earlier.

7. Replace the plastic cover and screw into place

using the two M3 screws.

To attach the mounting kit to the ATR110

Follow these steps to attach the mounting kit to the

ATR110, if it is not pre-fitted to the device.

1. Remove the two M3 screws holding the plastic

back cover in place on the metal back plate.

2. Unscrew the four M4 screws holding the two

metal ‘U’ brackets together.

3. Unscrew the four screws holding the two plastic ‘U’-shaped mouldings to the top and bottom of

the mounting bracket.

4. Screw the mounting bracket to the back of the ATR110 using four M3 screws.

5. Replace the plastic ‘U’-shaped mouldings and screw into place.

6. Attach the unit to the pole following steps 3–7 above.

Figure 7. Mounting the ATR110 on a pole (View A)

Note: Mount the unit in either orientation.

Figure 8. Mounting the ATR110 on a pole (View B)

3.4 Interface options

3.4.1 Serial connection

Connect a serial ATR110 device using an RS232 interface directly into a COM port. You must

specify the baud rate, parity, data bits and stop bits.

Note: A serial ATR110 communicates directly with the COM port and does not require any special

software or drivers to be loaded.

3.4.2 USB connection

Connect a USB ATR110 device using one of three possible options. These options are compatible

with all Linux and Windows operating systems from XP onwards.

3.4.2.1 Keyboard interface

Virtual keyboard using Windows or Linux drivers

This allows the device to operate without additional drivers, with the ATR110 emulating a keyboard.

This is one-way communication; it is not possible to control the device directly in this mode.

This mode will be slower than the other options as it adds an inter-character delay when typing the

barcode data. For higher throughput, consider using a HID or CDC interface.

3.4.2.2 CDC interface

Virtual serial mode using the Windows CDC driver

This assigns a COM port and the device will communicate as a virtual serial device. Due to the

nature of CDC serial port drivers, the COM port disappears if the unit is unplugged.

3.4.2.3 HID Interface

Access-IS recommends the use of the HID interface for reliability. A HID interface recovers properly

in the event of accidental disconnects or system power fluctuations; a CDC interface may not

recover in these situations.

HID interface using the Access driver (Windows only)

The Access Serial Ports Service driver is fully configurable and outputs data in virtual serial or

virtual keyboard. The output itself can be parsed and reformatted. The serial port is permanent and

does not disappear if you unplug or hot swap the unit. This is one-way communication and the only

command that you can send to the device is AIS_BO to enable or disable barcode reading. Refer

to page 28 for more information.

HID interface without the Access driver

This method is only suitable is you are familiar with HID programming.

It is possible to communicate directly with the ATR110 using the operating system’s built-in HID

drivers. In this instance, HID reports, exactly 64 bytes in length, are sent between the host and the

ATR110.

The implementation of this driver and the method of interaction will depend on the version of the

host operating system. You should refer to the HID programming guide for the operating system that

you are using.

Refer to HID reports on page 32 for the details of the HID reports used with the ATR110.

3.5 Serial installation

A serial ATR110 communicates directly with the COM port and does not require any special

software or drivers to be loaded.

1. Switch off the computer.

2. Connect the serial cable to a COM port on the computer and finger-tighten the two thumbscrews

to secure the connector to the port.

3. If using a USB power injector cable, plug the injector cable into the coaxial power connector on

the Y-cable and then plug the USB connector into a powered USB port on the computer.

If using an Access-supplied power supply, plug the power cable into the coaxial power

connector on the Y-cable and then connect the external power supply to an AC outlet.

4. Once the device is connected, switch on the computer.

3.6 USB installation

Note: If you intend to use the Access driver, ensure that you install the driver before you connect

the device to the computer.

3.6.1 Driverless keyboard output

There is no additional driver required for this mode. Connect the USB cable from the ATR110 to a

USB port on the computer.

3.6.2 CDC driver

This method for USB installation uses the Windows CDC drivers.

For this method to operate, you must install the CDC drivers using the file, AccessISCDC.inf,

which you can download from http://www.access-is.com/gettingstarted/.

The download (USB Driver for CDC Mode) includes full instructions for use.

Windows assigns a virtual COM port to the ATR110 device. You can find out the COM port number

in Device Manager. You will require the port number to configure the ATR110.

3.6.3 Custom HID

3.6.3.1 HID interface using the Access serial driver (Windows only)

The recommended method for using a USB ATR110 is to configure the device to operate in HID

mode. This allows the device to communicate with the Access driver.

For this method to operate, you must first install the Access driver (Access Serial Ports Service

(ASPS)). Download ASPS from http://www.access-is.com/gettingstarted/.

The download (ASPS Software) includes full instructions for use.

Ensure that you install the driver before connecting the ATR110 to the host.

3.6.3.2 HID interface without the Access driver

There is no additional driver required for this mode. Connect the USB cable from the ATR110 to a

USB port on the computer.

3.7 Test the device

Once you have connected the device and installed the relevant drivers, if applicable, you can test

the device. To do this, wave a piece of paper in front of the glass; the reader’s LEDs should

illuminate. If the device fails to respond when connected to the host, refer to the Troubleshooting

section in this document.

3.8 Configuration software

Connect to, and configure, the ATR110 using your own configuration tool, a terminal emulation

program or the Access-IS configuration tool, which you can download from http://www.access-

is.com/gettingstarted/.

Refer to the Command reference on page 18 for details of the commands, which you can use to

configure the ATR110.

3.9 Troubleshooting

If the ATR110 does not appear to be working, refer to Table 1 to help identify and resolve the

problem.

For further assistance, contact [email protected].

Alternatively, use the Contact Customer Support Team page on the Access-IS website.

Note: Do not attempt to disassemble the ATR110 if it does not operate correctly.

Table 1. Troubleshoot the ATR110

Problem

Solution

ATR110 not transmitting data to host

Check that all cable connections between the ATR110

and host are secure.

Ensure that the unit has power.

ATR110 cannot scan barcode

Ensure that the unit is configured to read the barcode that

you are scanning.

If scanning a paper document, ensure that the print quality

is good.

If scanning a barcode on a mobile phone, ensure that you

set the screen backlight on the phone to its brightest

setting.

3.10 Maintenance

3.10.1 Cleaning

Clean the glass with a lint-free cloth. If the glass is dirty, wipe the glass with a lint-free cloth

moistened with isopropyl alcohol or use an alcohol wipe. Do not use abrasive cleaners.

3.10.2 Storage

Store the unit in its original box, at a temperature of -30°C to 70°C.

4. Operating modes

The ATR110 operates in one of three ways, as defined by the AISOMD command. Refer to the

Command reference on page 18 for a list of commands that you can send to configure the ATR110.

4.1 Mode summary

4.1.1 Dumb mode

The ATR110 is a one-way communication device.

The device detects the media and activates the imager and illumination. When the ATR110 reads

the document, it sends the data to the host, activates the ‘Good Read’ indicators, and disables the

imager and illumination. The imager and illumination do not reset until the ATR110 sensor fails to

detect any media for 0.5 seconds.

4.1.2 Host mode

The ATR110 is a two-way communication device that reads barcodes and does not show any

indicator lights until the host computer accepts or rejects the barcodes.

The device detects the media and activates the imager and illumination. When the device reads the

barcode, it sends the data to the host and disables the imager and illumination. The ATR110 waits

for a response from the host to accept or reject the data, which activates the ‘Good Read/Bad Read’

indicators on the device. The ATR110 waits for up to two seconds for an ‘Accept/Reject/Ignore’

command to activate the indicators. The host sends an ‘Ignore’command to reset the imager if no

response from the indicators is required. The imager and illumination do not reset until the sensor

fails to detect any media for 0.5 seconds.

4.1.3 Interactive mode

Note:This is not the recommended mode for new installations.

The ATR110 is a two-way communication device, controlled fully by a host.

The ATR110 detects the media and sends a command to the host with this information. If the media

is removed, a second command is sent telling the host the media is no longer detected.

If the media is present, the host sends a command to activate the imager and illumination. When the

ATR110 reads the barcode, it sends data to the host. The imager and illumination are not disabled.

The ATR110 waits for a response from the host to accept or reject the data, which activates the

‘Good Read/Bad Read’ indicators and disables the imager and illumination. An ‘Ignore’ command

may also be used, although untriggering the unit is more useful in most cases.

At any time, the host can send ‘Good Read’ or ‘Bad Read’ commands or commands to activate or

deactivate the imager and illumination.

4.2 Dumb mode

Figure 9 shows the process for an ATR110 in Dumb mode.

Figure 9. Dumb mode process flow

4.2.1 Dumb mode example

Comments

ATR Command to Host

Host Command to ATR

Media placed in front of

ATR110.

Imager activated and

barcode scanned.

Illumination activated as

defined in the settings.

Data sent as configured (USB/Serial)

No media detected for 0.5

seconds; ATR110 resets.

Media Detected

Imager and

Illumination

Activated

Barcode Read

Data Sent to Host

Lights ‘Good

Read’ (as Settings

Instruct)

Reader Idle

Imager and

Illumination

Deactivated

Reader Idle

4.3 Host mode

Figure 10 shows the process for an ATR110 in Host mode.

Figure 10. Host mode process flow

Media Detected

Imager and

Illumination

Activated

Barcode Read

Data Sent to Host.

Imager and

Illumination

Deactivated

Accept or Reject?

Lights ‘Bad Read’

(as Settings

Instruct)

Lights ‘Good

Read’ (as Settings

Instruct)

Reject Accept

Reader Idle

Ignore Command or

No Response within Timeout

4.3.1 Host mode example

4.3.1.1 Accept

Comments

ATR Command to Host

Host Command to ATR

Media placed in front of

ATR110.

Imager activated and

barcode scanned.

Illumination activated as

defined in the settings.

Data sent as configured (USB/Serial)

Host decides to accept or

reject the data.

‘Good Read’:

AISXXR0

Lights activated as defined

in the ‘Good Read’settings.

No media detected for 0.5

seconds; ATR110 resets.

4.3.1.2 Reject

Comments

ATR Command to Host

Host Command to ATR

Media placed in front of

ATR110.

Imager activated and

barcode scanned.

Illumination activated as

defined in the settings.

Data sent as configured (USB/Serial)

Host decides to accept or

reject the data.

‘Bad Read’:

AISXXR1

Lights activated as defined

in the ‘Bad Read’settings.

No media detected for 0.5

seconds; ATR110 resets.

4.3.1.3 Ignore

Comments

ATR Command to Host

Host Command to ATR

Media placed in front of

ATR110.

Imager activated and

barcode scanned.

Illumination activated as

defined in the settings.

Data sent as configured (USB/Serial)

Host decides to accept or

reject the data.

‘Ignore and Continue’:

AISXXR2

No media detected for 0.5

seconds; ATR110 resets.

4.4 Interactive mode

Figure 11 shows the process for an ATR110 in Interactive mode. The host can send ‘Good Read’

and ‘Bad Read’commands to the ATR110 at any time.

Figure 11. Interactive mode process flow

Media Detected,

Message Sent

Requesting

Trigger

Send Trigger?

Imager and

Illumination

Activated

Trigger

Barcode Read

Data Sent to Host

Accept or

Reject?

Lights ‘Bad Read’

(as Settings

Instruct)

Lights ‘Good

Read’ (as Settings

Instruct)

Imager and

Illumination

Deactivated

Reject Accept

Reader Idle

Untrigger

Force Trigger

Reader Idle

Force Untrigger

Ignore Command

4.4.1 Interactive mode example

4.4.1.1 ‘Good Read’initiated by ATR110 detecting media

Comments

ATR Command to Host

Host Command to ATR

Media placed in front of

ATR110. The ATR110

sends commands to host

notifying of media.

[0x16][0x0D]TRIG:1[0x16][0x0A]

Host sends a command to

trigger the imager.

[0x16][0x74][0x0D]

Imager activated and

barcode scanned.

Illumination activated as

defined in the settings.

Data sent as configured (USB/Serial)

Host decides to accept or

reject the data.

‘Good Read’:

AISXXR0

Lights activated as defined

in the ‘Good Read’settings.

No media detected for 0.5

seconds; ATR110 resets.

4.4.1.2 ‘Good Read’initiated by host sending trigger command

Comments

ATR Command to Host

Host Command to ATR

Host sends a command to

trigger the imager. This

could be due to a second

sensor.

[0x16][0x74][0x0D]

Imager activated, it remains

triggered until untriggered or

a ‘Good Read/Bad Read’

command is received. Lights

activated as defined in the

settings.

Data read by imager.

Data sent as configured (USB/Serial)

Host decides to accept or

reject the data.

‘Good Read’:

AISXXR0

Lights activated as defined

in the ‘Good Read’settings.

No media detected for 0.5

seconds; ATR110 resets.

5. Command reference

Commands are sent with a prefix of [0x16][0x4D][0x0D] causing the command sequence to

take the form [0x16][0x4D][0x0D]<Menu Command>. The menu commands are six characters

long with a parameter (if required).

To send a command to modify a configuration parameter

Send the six-character command concluded by a dot ‘.’ or an exclamation mark ‘!’. The dot stores

the setting permanently and the exclamation mark keeps it temporarily until power is removed from

the device.

For example, [0x16][0x4D][0x0D]AISKBL1. sets the keyboard localisation to United States

when the device is operating as a USB keyboard.

To query the current settings (including a temporary one)

Send the six-character command with a ‘?’instead of the parameter and the ATR110 will return the

command with the current setting.

For example, [0x16][0x4D][0x0D] AISINF? queries the device interface and returns the

current value.

To query the stored value

Send the six-character command with a ’^’instead of the parameter and the ATR110 will return the

command with the stored setting.

For example, [0x16][0x4D][0x0D] AISINF^ returns the current illumination mode.

To list parameter options

Send the six-character command with a ‘*’instead of the parameter and the ATR110 will return the

command with the parameter options.

5.1 Basic configuration

These commands set the device interface, connection parameters and specify the operating mode.

Table 2. Basic configuration commands

Command

Description

Default

Parameters/Range

AISINF

Selects the device interface.

When a Serial cable is used, the

configuration is overruled and AISINF0

is used.

When a USB cable is used, the

configuration AISINF0is overruled and

AISINF1 is used.

0 - Serial

1 - USB serial (CDC)

2 - USB keyboard

3 - HID POS

AISBAU

Sets the baud rate for a Serial

connection.

Only used when AISINF is set to 0

(Serial).

0 - 300 bps

1 - 600 bps

2 - 1200 bps

3 - 2400 bps

4 - 4800 bps

5 - 9600 bps

6 - 19200 bps

7 - 38400 bps

8 - 57600 bps

9 - 115200 bps

AISSCP

Set connection parameters for a Serial

connection.

Only used when AISINF is set to 0

(Serial).

0 - 7N1

1 - 7N2

2 - 8N1

3 - 7E1

4 - 7E2

5 - 8E1

6 - 7O1

7 - 7O2

8 - 8O1

AISKBL

Keyboard localization; this defines the

Windows keyboard mapping for correct

output of characters.

Only used when AISINF is set to 2 (USB

keyboard).

0 - US (United States)

1 - UK (United Kingdom)

2 - IT (Italy)

3 - ES (Spain)

4 - DE (Germany)

5 - CH (Switzerland)

6 - CZ (Czech Republic)

7 - FR (France)

8 - BE (Belgium)

9 - SE (Sweden)

AISCHR

Sets the inter-character delay (in

milliseconds).

Only used when AISINF is set to 2 (USB

keyboard).

1–250 milliseconds

AISOMD

Indicator mode setting.

0 - Dumb mode

1 - Host mode

2 - Interactive mode

AISTAM

Triggers Auto mode.

Only used when AISOMD is set to 2

(Interactive).

0 - Normal operation

1 - Automatic untrigger

when media removed

Command

Description

Default

Parameters/Range

DLYGRD

Sets the delay between successful

reading of one barcode and the reading

of another barcode.

Each unit is equivalent to 1 millisecond.

0–25000

5.2 Prefix and suffix solutions

These commands allow you to add a prefix and/or suffix to all barcodes.

Note: If you send more than one prefix or suffix to the device, they will stack in chronological order.

You must send a clear command if you want to use a single prefix or suffix.

Table 3. Prefix and suffix commands

Command

Description

Default

Parameters/Range

PREBK299xx

Adds a prefix to all barcode symbologies.

Any two-character hex ASCII code can

replace xx.

For example, to add STX (Start of Text)

as a prefix, use the command

PREBK29902.

You can add more than one prefix, as

required.

xx - Hex value

PRECA2

Clear all prefixes.

SUFBK299xx

Adds a suffix to all barcode symbologies.

Any two-character hex ASCII code can

replace xx.

You can add more than one suffix, as

required.

For example, to add CR (Carriage

Return) and ETX (End of Text) as a

suffix, use the command

SUFBK2990D03.

xx - Hex value

SUFCA2

Clear all suffixes.

Table of contents

Access ATR110 User manual

Popular Barcode Reader manuals by other brands