AccuBANKER AB4200 User manual

www.AccuBANKER.com
AB4200
Bank Grade Bill Counter
USER GUIDE

2
Thank you for trusting AccuBANKER with your cash
handling needs. In order to optimize the performance
of your equipment, we encourage you to thoroughly
read this user guide prior to use.
®

3
Table of Contents
Table of Contents .............................................................................................3
Introduction ......................................................................................................4
Box Contents ....................................................................................................4
1. Safety Instructions........................................................................................5
2. Equipment Overview....................................................................................7
2.1 Part Description ......................................................................................7
2.2 Control Panel Description ......................................................................8
2.3 Display Brightness Adjustment ............................................................10
2.4 Adjusting Counterfeit Detection Features (MG-UV-DD-LEVEL)......10
2.5 Counting Polymer Bills ........................................................................11
3. Getting Started............................................................................................12
3.1 Installation ............................................................................................12
3.2 Bill Guider Installation .........................................................................12
3.3 Bill Selection / Placement.....................................................................13
4. Operation....................................................................................................14
4.1 Counting Operation ..............................................................................14
4.2 Miscounting errors................................................................................14
4.3 Thickness Knob Adjustment (Feeding Gap) ........................................15
4.4 Emergency Stop button ........................................................................15
5. Warning and Error Messages .....................................................................16
6. Specifications .............................................................................................17

4
Introduction
The AB4200 Bank Grade bill counter is the perfect solution for a fast,
accurate and reliable banknote counting process. This equipment is designed
to meet the most demanding applications in today's financial market.
Three different models are available:
AB4200 - Counter without counterfeit detection
AB4200 UV - Includes ultraviolet (UV) counterfeit detection function
AB4200 MG/UV - Includes magnetic (MG) and ultraviolet (UV) counterfeit
detection functions
Among the most significant features this model offers are:
1. Reliable, Fast, Versatile, and Easy operation
2. Long-lasting Control Panel designed using hard keys
3. Variable counting speeds of 1200-1500-1800 bills/min
4. Includes an external display
Box Contents
1. Bill Counter
2. Bill Guider
3. Power Cord
4. External Display
5. Printing Materials
1
2
3
4
5

5
!
!
1. Safety Instructions
Warning
Do not use this product in areas where it may be exposed to water or other
liquids.
Unplug this product from the electric outlet before cleaning. Do not use liquid
oraerosol cleaners. To clean, use a damp cloth.
To reduce the risk of electric shock, do not disassemble this product. Take
it to qualified service personnel when service or repair work is required.
Opening or removing covers may expose you to dangerous voltages or other
risks. Incorrect reassembly can cause electric shock when the appliance is
subsequently used.
Only use the cable provided with the unit. The use of other cables may result
in electric shock, fire, or cause serious damage to the unit.
Do not operate the unit in areas with high temperature or high humidity sinceit
may prevent it from working correctly.
Caution
When unplugging the power cord, do not pull it by the cord, but rather grip the
plug to pull it out. Not following these instructions may result in electricshock,
fire, or damage to the unit.
Do not use the unit if the power cord is damaged or if the plug socket contactis
loose. Not following these instructions may result in electric shock, fire, or
other hazards.
Do not place heavy objects over the cord and do not bend it excessively since
it could get damaged. Not following these instructions may result in electric
shock, fire, or other hazards.
When not using the unit for a long time, remove the power plug from the electric
outlet.

6
1. Safety Instructions (continued)
•Follow all warnings and instructions marked on the unit.
•This product is meant to be operated in an indoor environment with
proper ventilation.
•Do not place near direct sunlight, heat sources, or air conditioners.
•This product should only be operated with the power cord supplied and
the type of power source indicated in this user guide. If you are not sure
of the type of power supply in your location, consult your vendor or local
power company.
•To avoid the risk of fire or electric shock, never push objects into the unit
through the case slots or openings, since they may touch dangerous
voltage points or shortcut parts. Do not disassemble the unit.
•Never spill liquids of any kind on the product.
•Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
- When the power supply cord or plug is damaged or frayed*
- If liquid has been spilled into the unit, or it has been exposed to rain
or water*
- If the product has been dropped or the case has been damaged*
- If the product shows a noticeable change in performance
*Not covered under warranty
NOTE:Do not remove the "ground" prong from the power cord. It is a safety
feature meant to protect the user from harm and the equipment from damage.
!
If the unit does not operate normally while following the
instructions, adjust only those controls covered by the operating
instructions. Improper adjustment of other controls may result in
damage and will often require extensive work by a qualified
technician to restore the product to normal operation.

7
2. Equipment Overview
2.1 Part Description
1. Bill Guiders - Aligns the bills to be counted
2. Hopper Sensor - Senses when bills are on the hopper tray
3. Emergency Stop Button -Stops the counting operation
immediately
4. Hopper Tray -Bills are placed to be counted
5. Display/ Control Panel - Controls to operate different functions
6. Stacker Sensor - Recognizes when a bill is on the stacker
7. Stacker Tray -Location of counted bills
8. Carry handle -Used to carry and transport the equipment
9. Feeding Gap Adjustment Knob -Used to adjust the opening
where bills enter
10. Serial 1 port - Install Updates/ Technical Service
11. Serial 2 port -Auxiliary Display connection
12. USB port - Install Updates/ Technical Service
13. On / Off switch - Used to tum the equipment on and off
14. Power Jack - Connection for the power cord

8
2. Equipment Overview (continued)
2.2 Control Panel Description
•A/M: Automatic or Manual starting mode
By pressing the A/M button, the user can change between Auto
(automatic) and MNL (manual) counting modes. In Auto, the default
setting, the equipment begins counting automatically when the bills are
placed on the hopper. In manual mode, the equipment will only begin
counting once the START key is pressed.
•ADD: Adding function On / Off
This function allows the equipment to add up all the consecutive
operations made with this function ON.
•SPEED: Change the speed between 1200-1500-1800 bill/min
Pressing the SPEED key repeatedly will display the three-speed options
available. Press "START" when the desired speed option appears.
** When the highest speed (1800 bill/min) is chosen, the MG function is not
available to be selected by the user**.
•MG: Magnetic Verification On/Off (MG/UV model only)
Allows the equipment to analyze the magnetic features of each bill during
the counting process. The equipment will stop counting if a bill is
considered suspicious. The MG sensitivity can be adjusted by the user
from 1-9.
**When the MG function is active, the highest speed (1800 bills/min) is not
available to be selected by the user**.

9
2. Equipment Overview (continued)
2.2 Control Panel Description (continued)
•UV: Ultraviolet Verification On/Off (UV and MG/UV model only)
This function allows the equipment to analyze the ultraviolet
characteristics of each bill while counting. The equipment will stop
counting if a bill is considered suspicious. The UV sensitivity can be
adjusted from 1-9, where 1 is the minimum and 9 is the maximum
sensitivity.
•DD: Bill Size Verification (Width) On/Off
This function allows the equipment to analyze the width of each bill
while counting. The equipment will stop counting if a bill with a different
size is found. The DD sensitivity can be adjusted from 1-9, where 1 is the
minimum and 9 is the maximum sensitivity.
•LEVEL: This allows the adjustment of the emission intensity of the
counting sensors. It can be adjusted from 1-9, where 1 is the minimum
and 9 is the maximum.
•C key: Used to clear (delete) the counted data from the display
•BATCH: Preset batch selection
By pressing the BATCH key repeatedly, the preset batch value will
change among 5, 10, 20, 25, 50, 100, 200, or off.
•START: While in MANUAL mode, used to Start or Stop the count. Also
used to accept and confirm batch selection as well as security functions
sensitivities.
•Numeric Keys: Used to set up batch sizes manually and to enter the
value for security function sensitivity levels.

10
2. Equipment Overview (continued)
2.3 Display Brightness Adjustment
The control panel's display may need to be adjusted (lightened or darkened)
to read the screen more easily. Press the "7" key to enter into the
BRIGHTNESS menu. Next, press "ADD" to increase or "SPEED" to
decrease the brightness on the display. Press START to save the brightness
level and return to count mode.
2.4 Adjusting Counterfeit Detection Features (MG-UV-DD-LEVEL)
The sensitivity level of the detection functions may be adjusted (increased or
decreased) from 1-9, where 1 is the lowest sensitivity and 9 the highest
sensitivity.
To modify the values, press the key for the desired security function for 3
seconds until the display shows the current sensitivity value for the selected
feature. Use the numeric keypad to select a new value. Press START to save
the selection and return to counting mode.
NOTE: If the equipment is frequently reporting error messages, related to
any security feature (MG - UV - DD), the current sensitivity setting
for these functions may need to be adjusted as they may be too high
(sensitive) for the current bills being counted.