Accuphase DAC-40 User manual







付属品 ユーティリティCD、セットアップガイド
使用方法
取り付け方法
取扱説明書
820-3288-00 (B1) Printed in Japan
F131.1X
ディジ タ ル 入 力 ボ ード DAC-40
お願い 製品に対するお問い合わせ、または異常が認めら
れるときは、お求めの当社製品取扱店または、当
社品質保証部へご連絡ください。
 お客様カードは付属していません。
アキュフェーズ株式会社
〒２２５-８５０８ 横浜市青葉区新石川２-１４-１０
 TEL０４５（9０１）２77１（代）
＊イラストは E-460 です。

 
接続ケーブル
  
  
  
保証特性、適合規格
  
  
  
 
  
  
   
   
  
COAXIAL 端子 
OPTICAL 端子





❶ 󰴤 󰴥󰴦

❷

❶
❷
図1 
 
❸                
 図2 


❹

E-３0８, C-２4５, CX-２60への増設について

 
注意
注意
入力の選択方法
DAC切替機能のある機種

その他の機種
図1 図2
ガ イド レ ー ル
DIG IT
INPUTS
COAX IAL
OPT ICAL
USB
modelDAC-40
サブパネル
オプショ ン ・ ボード
ガ イド レ ー ル
＊プ ラグ 先 端 の
保護キャップをはずす。
端子の保護プラグを抜く。
端子がシャッター付き
の場合
端子が保護プラグ付き
の場合
端子 ： 押すとシャッターが
プラグ
光ファイバ ー
内 側 に 開く。
OPTICAL端子
端 子 と プ ラ グ の ガ イド を
合 わ せ てしっ かり 差し込 む 。
端 子とプラグ の 形状を合わ
せ てしっ かり 差し込 む 。
タイプ B プラグ
USBケーブ ル
USB端子
＊USB ダストカバーを取る。
光ファイバーの接続
USB（タイプB）の接続
プラグ
プラグ
USB 端子



 

    





注意

ACCUPHASE LABORATORY, INC.
YOKOHAMA, JAPAN
820-3288-00 (B1) Printed in JapanF131.1X
INSTRUCTION MANUAL
Digital Input Board DAC-40
Thank you for your purchase of the DAC-40 digital input board. This optional board plays music
signals supplied from the digital outputs of a CD player or similar source. You can connect to the
player using either coaxial cable or optical fiber. You can also use a USB cable to connect to and
play music data from a personal computer. Install this board into an option slot on the rear panel of
your supporting Accuphase analog device, and use its digital input jacks to connect to the external
source.
Note that usage procedures vary according to the device you are using. Please be sure to read
your device’s documentation before starting use.
Using the DAC-40
How to Install Illustration shows installation on the E-460.
COAXIAL Accepts digital coaxial cable.
OPTICAL Accepts JEITA-compliant optical fiber cable.
*Retain the protection cap or dust cover for future use.
Adds one coaxial input, and one optical-fiber input, and one USB input to the device.
Use these to input digital sound signals from digital components.
Connection cables
COAXIAL: Connects to digital coaxial cable.
OPTICAL: Connects to optical fiber cable.
USB: Connects to cable with USB type B connector end
Guaranteed specifications
Input format: IEC 60958/AES-3 for COAXIAL
JEITA CP-1212 for OPTICAL
USB2.0 Hi-Speed (480M bps)
Sampling freq: 32-96 kHz (OPTICAL),
32-192 kHz (COAXIAL, USB)
Quantization bit rate: 24 bits
Digital input: COAXIAL 0.5 Vp-p, 75 ohms
OPTICAL -27 to -15 dBm
USB
❶Turn off the device power.
❷On the rear panel, remove the slot cover of the slot you wish
to use. (see Fig. 1 )
◆Retain the slot for future use.
❸
Insert the board along the top and bottom guide rails in the
slot (see Fig. 2 ).
Push the board in gently until it touches the connector at the
back of the slot, and then give it a firmer push so that it seats
fully into the connector.
❹
Secure the board by screwing in the top and bottom screws.
Remove the plug cap.*
Pull off the blind plug. Plug
Optical fiber cable
Push to open
shutter.
OPTICAL jack
Align the plug with the
port and push firmly in.
Type-B plug
USB cable
USB port
Remove the USB dust cover.*
Plug
Plug
Align plug guide with
jack, and push in firmly.
USB Port Connect to the type-B plug on a USB cable. Before connecting to your computer, install
the software from the included USB Utilities CD as explained in the included Setup Guide.
Accessory: Utility CD and setup guide
 Turn off the device power before installing or removing option boards. Installing a board
while power is on may damage the equipment.
 Keep fingers out of the opened slot. Do not place anything other than the board into the slot.
 Avoid touching the board’s soldered areas, connector contacts, and components. Touching
these areas may damage the circuitry or the contact. Hold the board by the edges or along
its panel.
 Tightly screw in the two screws all the way (by hand). If screws are loose, terminals may
separate from ground, resulting in poor contact or equipment damage.
 Do not use electrical contact enhancers or conductivity agents on inputs and cable
connectors. The warranty does not cover damage caused by these materials.
Caution
When connecting a component, please do not connect up both coaxial cable and (balanced
or line (unbalanced)) analog cable at the same time. Simultaneous connection of both
cable types will produce a ground loop, resulting in electrical noise.
◆ For information about how to set up and use a computer connected by USB, refer to the
computer's user documentation.
❶The DAC-40 will automatically lock in the input signal from the ①coaxial, ②optical, or ③USB
connector, in that order, when power comes on or when the input selector is set to OPTION.
❷To select the input jack to use on the DAC-40 (coaxial, optical, or USB): disconnect the input cables
you do not wish to play from, or else switch off the power to the input devices you do not wish to play
from.
If installing on an E-308, C-245, or CX-260…
Owing to power limitations, these devices cannot accept more than a single DAC-30. You
can, however, install both a DAC-40 and an AD-30, AD-20 (Analog Disk Input Board) for
simultaneous use.
Note
Note
Selecting Your Input
If your device includes a DAC switch...
Use the DAC input switch button to select the input.
Otherwise...
DIG IT
INPUTS
COAX IAL
OPTICAL
USB
modelDAC-40
Guide rail
Guide rail
Fig. 1 Fig. 2
Sub-
panel
Option
board