Ace Baby Furniture MDBEW1076 User manual

Panolam panels consist of a
melamine resin impregnated
decorative paper, thermally fused
to an industrial grade of
particleboard. Thermal fusion takes
place under heat and pressure and
permanently bonds the resin
impregnated paper to the
substrate. The process of thermal
fusion produces a permanent bond
between the melamine surface and
the substrate. Panels are supplied
with decorative faces on both
sides.
Panolam panels are produced with
particleboard conforming to the
formaldehyde emission
requirements for particleboard of
the U.S. Department of Housing
and Urban Development (HUD)
and the CPA Voluntary
Formaldehyde Emission
Monitoring Program. Under 24
CFR 3280 Manufactured Home
Construction and Safety
Standards, formaldehyde emission
must be less than 0.3 ppm for
particleboard tested in accordance
with FTM-2, the NPA/HPMA Large
Scale Chamber Test. Panolam
decorative panels, tested in-house
in accordance with FTM-2, show
formaldehyde emission less than
0.3 ppm.
This warranty does not cover any
damaged or defective parts that
result from installation and
assembly, normal wear and tear,
abuse, negligence, improper use or
alteration to the finish, design, and
hardware. The specific legal rights
of this warranty may vary from
state to state. Some states do not
allow any exclusion or limitation of
incidental damages. Some states
do not allow limitation on how long
an implied warranty lasts.
Composition
and Materials
Panels can be easily cleaned with
warm water and mild soaps. Do not
use cleansers which contain
abrasives, acids or alkalis.
Maintenance
Never allow children to climb or
hang on the rod, drawers, doors, or
shelves.
Safety All products made of
Low VOC Materials.
We will replace any missing parts
at the time of purchase or any
defective item within a one year
period from the date of original
purchase. Please keep your receipt
so that we may process your
warranty request. This warranty
only covers new units with original
packaging and ownership, and is
not transferable. It does not cover
any used, secondhand or demo
models.
One Year Limited Warranty Formaldehyde Emission
Test Data
Please share your comments on
our website!
facebook.com/AceBabyFurniture
Thank you for supporting
U.S.A. - made products.
Instruction Manual is available
on www.acebabyfurniture.com
Customer Support:
Toll Free [phone]
Like Us on Facebook!
Mobile Desk
Page 8
Mobile Dress-Up Closet
Mobile Bookcase
www.acebabyfurniture.comwww.facebook.com/AceBabyFurniture
MDBEW1076
MDBCH1077
MDBNM1078
MDBWT1079
MDBBL1080

I
I
I
0
Desk Parts
Assemble Chair Front Panel
24 Assemble Chair Back Panel 25
Tighten Inside Connectors
26 Assemble Chair Backrest 27
Assemble Chair Right Panel
28
CBottom Shelf
BRight Panel
ALeft Panel
DMiddle Shelf
ETop Shelf
Chair Parts
QQ R
R
S
S
T
T
Chair Seat
PChair Right Panel
OChair Left Panel
RBackrest
SFront Panel
TBack Panel
FLeft Back Panel
GRight Back Panel
HDrawer Holder Right
IDrawer Holder Left
JRight Side (Drawer)
KLeft Side (Drawer)
LFront Panel (Drawer)
Back Panel (Drawer)
M
Connector Bolt 5mm (x22)
Connector Bolt 5mm (x4)
NBottom (Drawer)
M
L
N
H
I
6
Screws 20mm (x16)
8
Pastic Hole Plugs (x8)
9
Grommet Hole Cover
(x1)
10
4
P
P
O
Page 2 Page 7
Note: Tighten 2 connector locks on the
sides and 2 connector locks on the top

Attach Casters
Overview of
CHAIR
Assembly
Overview of
DESK
Assembly
Assemble Left Side
Assemble Drawer Support
x4
Assemble Right Side
x4
Assemble Left Side Panel
20 Assemble Right Side Panel 21
Assemble Chair Seat
22 Tighten Chair Seat Connectors 23
Q
P
O
O
A
Page 6 Page 3

M
M
N
Assemble Hardware
To Drawer Parts Attach Drawer Right Side
Insert Drawer Bottom Assemble Drawer Front
9Attach Drawer Handle 10
Attach Drawer Left Side
6
Screw Rail to Drawer
11 Assemble Side Panels 12
Connector Bolt 5mm (x3)
Connector Bolt 5mm (x2)
Place screws based on
desired height of desktop
Assemble Bottom Self
13 Assemble Top Self
14
Assemble Grommet Hole Cover &
Plastic Hole Plugs
19
Grommet Hole Cover
(x1)
10
Pastic Hole Plugs (x8)
9
15 Assemble Side Panel Assemble Middle Shelf 16
Slide down the middle part to fully
rest on the 4 screws. Tighten the
screws with phillips screw driver.
17 Assemble Right Back Panel
Screws 20mm (x8)
8
18 Assemble Left Back Panel
Screws 20mm (x8)
8
Page 4 Page 5