Ace Plus EX-G011 User manual

EX-G011 v1.3
4x4 HDMI over CAT5 Matrix with
IR Pass-through
User Manual
Made in Taiwan
ACE PLUS CORP.

Safety and Notice
The EX-G011 v1.3 4x4 HDMI over CAT5 Matrix with IR Pass-through has been tested for
conformance to safety regulations and requirements, and has been certified for international use.
However, like all electronic equipments, the EX-G011 v1.3 should be used with care. Please read and
follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage
to the unit.
zFollow all instructions and warnings marked on this unit.
zDo not attempt to service this unit yourself, except where explained in this manual.
zProvide proper ventilation and air circulation and do not use near water.
zKeep objects that might damage the device and assure that the placement of this unit is on a
stable surface.
zUse only the power adapter and power cords and connection cables designed for this unit.
zDo not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device
before cleaning
.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 1 of 25

The EX-G011 v1.3 4x4 HDMI over CAT5 Matrix with IR Pass-through provides the most flexible
and cost effective solution in the market to route high definition video sources plus multi-channel (up to
7.1-channel) digital audio from any of the four HDMI sources to the remote displays at the same time.
Through low cost Cat-5/5e/6 LAN cables, not only high quality video and audio can be transmitted to
the display sites, but also users can switch among four HDMI sources using the push-in button or
remote control. With single power design at the source site, each remote module is easily installed
without power supply. Furthermore, the built-in IR extension function makes users at display site
access the DVD player, PS3 or any HDMI supported devices directly!
Introduction
HDMIcable
2xCAT5ecable
4xHDTV
4xHDMISource
EX-G011RX
PS3
Blu-rayDiscPlayer
TiVo
HDMICamera
Matrix’sremote
control
IRreceiver
EX-G011 RX
EX-G011 RX
EX-G011 RX
Sourcedevice’s
remotecontrol
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 2 of 25

Features
zState-of-the-art Silicon Image (founder of HDMI) chipset embedded for upmost compatibility and
reliability
zHDM I.3c compliant
zHDCP compliant
zAllows any source to be displayed on multiple displays at the same time
zAllows any HDMI display to view any HDMI source at any time
zSupports 7.1 channel digital audio
zSupports default HDMI EDID and learns the EDID of displays
zThe matrix master can switch every output channels to any HDMI inputs by push-in button, IR
remote control, or RS-232 control
zAllows controlling local HDMI sources such as DVD and TiVo by attached IR extender from
remote receiver to matrix master
zAllows to control matrix master through IR remote control at remote receiver’s site
zExtends video signal up to 35m (115 feet) over CAT5e at 1080p and likely longer with better HDMI
source device (such as PS3), better grade HDMI display (such as Sony X-series HDTV), and
better quality solid CAT6 cable
zEasy installation with rack-mounting and wall-mounting designs for master and receiver
respectively
zFast response time – 2~5 seconds for channel switch
Specifications & Package Contents
Model Name EX-G011 v1.3
Technical EX-G011 EX-G011 RX
Role of usage True 4x4 matrix switcher
Transmitter [TX] Receiver [RX]
HDMI compliance HDMI 1.3c
HDCP compliance Yes
Video bandwidth [EX-G011 v1.3]
–
Single-link 225MHz [6.75Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60 36-bit color
Audio support Surround sound (up to 7.1ch) or stereo digital audio
HDMI over CAT5
transmission range Full HD (1080p): 35m (115ft) [CAT5e] / 40m (130ft) [CAT6] HD (720p/1080i): 50m (165ft) [CAT5e] / 55m (180ft) [CAT6]
HDMI equalization N/A 8-level digital rotary control
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 3 of 25

ESD protection [1] Human body model — ±15kV [air-gap discharge] & ±8kV [contact discharge]
[2] Core chipset — ±8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω; single 50
Ω
]
Input 4x HDMI
1x RS-232
1x RJ-45 TMDS
1x RJ-45 DDC
1x IR socket for IR receiver
Output 4x RJ-45 TMDS 4x RJ-45 DDC
5x IR socket for IR blaster 1x HDMI
HDMI Input selection Push-in button/IR remote
control/RS-232 control Push-in button / IR remote control
HDMI source control Controllable via IR pass-through from IR receiver at RX to IR blaster at TX
IR remote control Electro-optical characteristics:
τ
= 25°/ Carrier frequency: 38kHz
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
RS-232 connector DB-9 [9-pin D-sub female]
3.5mm connector Earphone jack for IR blaster
[IR Main] IR control on all source devices
[IR1~IR4] IR control on individual source
device
Earphone jack for IR receiver
[IR] Receives IR commands from remote
control
DIP switch [SW1~SW4] 2-pin for EDID and audio setting modes
[SW Main] 4-pin operation mode & firmware update
Mechanical EX-G011 EX-G011RX
Enclosure Metal case
Dimensions
(L x W x H)
Model 340 x 110 x 44mm [1’1” x 4.3”x1.7”] 90x 85 x 25mm [3.5”x3.3”x1”]
Package 545 x 230 x 110mm [1’10” x 9.1” x 4.3”]
Carton 580 x 570 x 260mm [1’11”x1’11”x10.2”]
Weight Model 1220g [2.7 lbs] 180g [6.3 oz]
Package 3.2 kg [7.0 lbs]
Fixedness 1U rack-mount with ears
Wall hanging holes Wall-mount with screws
Power supply 5V 6A DC Not necessarily required
1
Power consumption 20 Watts [max] 1 Watt [max] (provided by EX-G011)
Operation
temperature 0~40°C [32~104°F]
Storage temperature -20~60°C [-4~140°F]
Relative humidity 20~90% RH [no condensation]
Package Contents
1x EX-G011
1x IR blaster2
2x Rack-mounting ear
1x IR remote control2
1x User Manual
4x EX-G011 RX
4x IR receiver
8x Wall-mounting screws
1x 5V 6A in-line power adapter
1x C5-type power cord
1The EX-G011 RX has been tested extensively and found that it doesn’t require external power
supply. If in rare situation you find it cannot work with the EX-G011, please use any +5V power
adapter to plug in the power jack and see if it can work. If not, please contact your technical
support for further service.
2Additional IR remote controllers and IR blasters can be purchased as optional accessories to
control the HDMI sources located separately.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 4 of 25

EX-G011
1. Power: Power indicator LED
2. IR: IR receiver
3. Input: Input source indicator LED
4. HP1–HP4: Connection status indicator LED for each output channel
5. Port1–Port4: Input source channels mapping LED for each output channel
6. Port1 Select–Port4 Select: Push-in button for selecting input channel
7. ON–OFF: Power ON/OFF
8. RS-232: RS-232 control port
9. +5V DC: 5V DC power jack
10. SW Main: DIP switches [see DIP Switch section in p.8]
11. SW1–SW4: DIP switch [see DIP Switch section in p.7]
12. IN1–IN4: HDMI inputs
13. IR1–IR4: IR extender jacks for individual HDMI source control with IR blasters
14. OUT1–OUT4: RJ-45 TMDS/DDC outputs for each output channel
15. IR Main: IR extender jack for all HDMI source control [default socket for IR
blaster]
Panel Descriptions
7 8 14
10 12
11 15
9 13
1
2
5
4
3
6 3
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 5 of 25

EX-G011RX
1. +5V DC: Spare power jack for over 60m transmission when the RX may need external power
to work*.
2. A/V SIGNAL: Plug in the CAT5 connected to the respective A/V SIGNAL port on the
3. CHANNEL CONTROL: Plug in the CAT5 connected to the respective CHANNEL CONTROL
port on the EX-G011
4.INPUT CHANNEL: Display the current showing HDMI source channel
5.INPUT SELECT: Push button for switching input source channel in sequential order
6. Signal Level 0-7: Adjust the 8-level equalization control to the received HDMI signals. The
HDMI signal level varies from 0 (strongest) to 7 (weakest) for respective
transmission length from longest possible range to short distance. Please
adjust the signal level from 7 to 0 and stop turning the rotary switch
whenever the audio/video is playing normally. Inappropriate signal level
setting may cause overpowering issue that would shorten the product life
significantly!
7. HDMI Output: Connect to HDTV with a HDMI cable
8. IR RECEIVER: Plug in IR receiver
*The EX-G011 RX has been tested extensively and found that it doesn’t require external power
supply. If in rare situation you find it cannot work with the EX-G011, please use any +5V
power adapter to plug in the power jack and see if it can work. If not, please contact your
technical support for further service.
8
1
5
2 3
4
6
7
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 6 of 25
EX-G011

SW1-SW4 for EDID/Audio
Note
1If the HDTV shows video but without audio, please try to set audio mode to stereo.
2Factory default setting of [SW1]-[SW4] is pin-1 at OFF [
© ] & pin-2 at OFF [ © ] for 1080p
video and surround sound audio.
3 If you encounter any unsolved audio/video output problem during system installation,
please turn any [SW1]-[SW4] to pin-1 at OFF [
© ] & pin-2 at ON [ ª ] for safe mode to
enforce the system output up to 1080p video and stereo audio for system check. However,
the safe mode cannot be initiated if your HDMI™ source is set to enforce 1080p output. In
this case, please reconfigure your HDMI™ source to all resolution output for
troubleshooting.
4Bypass means the matrix will maintain playing the original format of HDMI signals in video
and perhaps audio. By setting at this mode, the users may encounter compatibility issue
among different kinds of HDMI sources and displays. If you cannot get the audio and/or
video output normally at the system installation, please change the DIP switch setting to
default mode or even safe mode to verify the functionality of the device.
5To learn the EDID of HDMI display for respective HDMI source devices, please see the [EDID
Learning] section in the next page for more detail information.
DIP Switch
Position Video Audio Description
Pin#1 Pin#2
OFF
[©]OFF [©]Up to
1080p Surround
1Default Mode2– Up to 1080p video & surround sound
audio output up to 7.1ch (DTS-HD & Dolby TrueHD)
OFF
[©]ON [ª] Up to
1080p Stereo Safe Mode3– Enforce the system output at 1080p
video and stereo audio for basic compatibility among
HDTVs
ON [ª] OFF [©]Bypass4Bypass4EDID Learning Mode5– for learning EDID from the
display while playing any received HDMI audio format
ON [ª] ON [ª]Bypass Stereo
EDID Learning & Stereo Mode5– for learning EDID
from the display while enforcing stereo output if any
HDTV cannot play surround sound normally
DIP Switch
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 7 of 25

SW Main for firmware update (for technical support only)
DIP Switch Position Pin#1 Pin#2 Pin#3 Pin#4
Normal Operation Mode [via RS-232
port]6OFF[©]OFF[©]OFF[©]OFF[©]
Normal Operation Mode [via USB port]7OFF[©]OFF[©]OFF[©]ON[ª]
Firmware Update
Mode8
Block A [main] ON[ª] OFF[©]OFF[©]OFF[©]
Block B
[remote] ON[ª] OFF[©]ON[ª] OFF[©]
Block C [HDMI] ON[ª] ON[ª] OFF[©]OFF[©]
Note
6Factory default for SW Main is pin#1-OFF[©], pin#2-OFF[©], pin#3- OFF[©], & pin#4-OFF[©].
PLEASE MAINTAIN THIS SETTING ATANYTIME FOR REGULAR USE VIA RS-232 CONTROL!
7Factory default for SW Main is pin#1-OFF[©], pin#2-OFF[©], pin#3- OFF[©], & pin#4- ON[ª].
PLEASE MAINTAIN THIS SETTING ATANYTIME FOR REGULAR USE VIA USB CONTROL!
8 Sequence for firmware update
WARNING! [Firmware update only can be done via RS-232 port and connection to PC set at COM1)
1. Power off the EX-G011. Execute the firmware update program on your PC via COM1 port
connection to the RS-232 port of the EX-G011.
2. Set the pin#1 of [SW Main]at ON[ª]for firmware update mode.
3. Set pin#2 and pin#3 at respective positions to assign which Block to be updated.
4. Power on the EX-G011. The firmware update program should begin this update
sequence automatically. If not, please check the RS-232 connection status between PC
and EX-G011.
5. After the OK message shows up to indicate the firmware update sequence for
designated Block is complete, please turn off the EX-G011.
6. Repeat step 3 ~ step6 if you want to update the firmware of the remaining Blocks.
7. Set the [SW Main]switch position to Normal Operation Mode.
8. Power on the EX-G011.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 8 of 25

IR Extender
IR Blaster IRReceiver
IR Sockets
EX-G011
IR Main: The default location for IR blaster to transmit all IR command signals received from any of the
four remote receivers to all of the HDMI sources.
IR PASS-THROUGH 1–4: IR blaster connected here can only transmit IR command signals from the
remote receivers that are setting at respective input channel from 1 to 4.
EX-G011RX
IR RECEIVER: IR receiver connected here can receive all IR command signals from the IR remote
controls of EX-G011 and all other HDMI source devices.
Definition of IR Earphone Jack
IR Blaster IR Receiver
You can buy any IR extension cables in the market that are compatible to the definition of the
IR sockets for the matrix if necessary for replacement use.
IR Pass-through
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 9 of 25

Supported IR Data Format
Data Format Suitable Not
Recommended
NEC 5
RC5 5
TOSHIBA MICOM
CODE 5
GRUNDIG CODE 5
SONY 12 BIT CODE 5
SONY 15 BIT CODE 5
SONY 20 BIT CODE 5
RCA CODE 5
RCM CODE 5
MATSUSHITA CODE 5
MITSUBISHI CODE 5
ZENITH CODE 5
JVC CODE 5
M50560-001P 5
MN6125H 5
MN6125L 5
MN6014_C5D7 5
MN6014-C6D6 5
MC14457P 5
LC7464(AHEA) 5
GEMINI_CM 5
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 10 of 25

EX-G011 as master
1. Connect all sources to HDMI Inputs on the 4x4 HDMI over CAT5 matrix master EX-G011
2. Connect each DDC output on the EX-G011 to respective DDC input on the remote receiver
EX-G011RX
3. Connect each TMDS output on the EX-G011 to respective TMDS input on the remote receiver
EX-G011RX
4. Connect IR blaster to the EX-G011 and direct the IR blaster to point towards the built-in IR receiver
of the HDMI source devices
5. Connect the +5V 6A DC power supply to the EX-G011
6. Power on all HDMI sources
7. Power on the EX-G011
EX-G011RX as receiver
1. Connect each HDMI output to HDMI displays
2. Connect the TMDS input on the EX-G011RX to the TMDS output on the EX-G011
3. Connect the DDC input on the EX-G011RX to the DDC output on the EX-G011
4. Connect IR receiver and place the IR receiver at the appropriate position that can receive the IR
signals sent from the users
5. Dial the 8-level rotary control switch to adjust the HDMI signal level until the picture and sound are
clear. It is recommended to dial from 7 to 0 to find the optimal visual experience
Hardware Installation
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 11 of 25

Source Side
Method A: Push-in Button
Push the red switch button on output port to select which port to be changed.
Method B: IR Remote Control
Choose the output port you want to make channel switch from OUT1 to OUT4 then press 1-4
channel button to choose the HDMI input source shown on the chosen output display.
Operation and IR Control
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 12 of 25

Method C: Software Control through RS-232 or USB port
Software Control Menu
1. Setting button:
Click Get button to read back device ID.
Click Set button to write device ID.
Click Rename button to open the String Table.
In the String Table, assign the captions for each input and output port for easy recognition.
For example
Rename the Input1 to “Blu-ray player”, Input2 to “Sat. receiver,” input3 to “Game console,”
input4 to “AV receiver,” input5 to “HDMI camcorder,” … etc., and rename output1 to “Conf.
RM1,” output2 to “Conf. RM2,” output3 to “Lobby,” output4 to “Main projector,” … etc.
Channel Control
HDMI Input Source
Selection Mapping
Area
HDMI Output
Port Selection
MappingArea
Status Indicator
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 13 of 25

Click Save String Table to save the caption setting (turn effective after program restart).
Click Set Default to pop up the confirmation message below to erase the captions and reset the
string table back to default setting (turn effective after program restart).
2. Scan button:
Serial Port Scan
Click Scan button, the machine will scan the all COM port and show them.
Select the RS232 serial port connected to the Matrix switch.
And set device ID 255 is for all device.
Only the same device id or 255 can get the command you sent.
Click OK. Get the new status from the Matrix switch (the port you select.)
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 14 of 25

3. Linkage button:
Click Linkage button to read back all status.
4. Open/Close button:
Click this button to close or open COM port.
5. Mapping button:
Select All Output
Select “set all output”, and then select the source on main menu. You
can quickly set all output to the same source.
Unselect All Output
Release output selection.
Select Input1~4-Output
Select Input Source. Then select the output port icon.
For example
Select input source 1. Then select output ports one and two. The
video and audio will be sent to ports one and two.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 15 of 25

6. Fast Select button:
Click Fast select button. Quick setting.
Input one > Output Port one
Input two > Output Port two
…..
Click Fast select pull down menu.
Select Input Num-Output Num
Input source #1 > Output port #1
Input source #2 > Output port #2 …..
Select Input* - All Output
Send the same source to all output.
7. Output Port:
Pull down menu and select which source to be sent to this output port.
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 16 of 25

One by one setting
On main menu screen
First select input source. Then select the output ports which you want to
send the video and audio from this source. When you select the input
source, the source will change to gray. When you select the output port
one by one, the selected output port will change to gray.
The linking line will change to yellow.
Group setting
First select output ports one by one. Then select the input source. The selected output ports
change the setting at the same time.
By using Terminal:
Baud rate: 9600
Data length: 8bit
Parity check: No
Stop bit: 1
Command Set:
COMMAND ACTION COMMAN
DACTION COMMAND ACTION
ST System Status C5 Output C select Input 5 F3 Output F select Input 3
VR Firmware Version C6 Output C select Input 6 F4 Output F select Input 4
A1 Output A select Input 1 C7 Output C select Input 7 F5 Output F select Input 5
A2 Output A select Input 2 C8 Output C select Input 8 F6 Output F select Input 6
A3 Output A select Input 3 D1 Output D select Input 1 F7 Output F select Input 7
A4 Output A select Input 4 D2 Output D select Input 2 F8 Output F select Input 8
A5 Output A select Input 5 D3 Output D select Input 3 G1 Output G select Input 1
A6 Output A select Input 6 D4 Output D select Input 4 G2 Output G select Input 2
A7 Output A select Input 7 D5 Output D select Input 5 G3 Output G select Input 3
A8 Output A select Input 8 D6 Output D select Input 6 G4 Output G select Input 4
B1 Output B select Input 1 D7 Output D select Input 7 G5 Output G select Input 5
B2 Output B select Input 2 D8 Output D select Input 8 G6 Output G select Input 6
B3 Output B select Input 3 E1 Output E select Input 1 G7 Output G select Input 7
B4 Output B select Input 4 E2 Output E select Input 2 G8 Output G select Input 8
B5 Output B select Input 5 E3 Output E select Input 3 H1 Output H select Input 1
B6 Output B select Input 6 E4 Output E select Input 4 H2 Output H select Input 2
B7 Output B select Input 7 E5 Output E select Input 5 H3 Output H select Input 3
B8 Output B select Input 8 E6 Output E select Input 6 H4 Output H select Input 4
C1 Output C select Input 1 E7 Output E select Input 7 H5 Output H select Input 5
C2 Output C select Input 2 E8 Output E select Input 8 H6 Output H select Input 6
C3 Output C select Input 3 F1 Output F select Input 1 H7 Output H select Input 7
C4 Output C select Input 4 F2 Output F select Input 2 H8 Output H select Input 8
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 17 of 25

Display Side
Method A: Push button for switching input channels
Press the INPUT SELECT push button to switch the input source on the respective output port
connected to the matrix receiver in sequential order. The selected input source will be displayed on
the seven segment display of INPUT CHANNEL.
Method B1: IR remote control for switching input channels
Please decide which input channel to be selected by pressing Source Selection 1 to Source
Selection 4. Or you can use left

—
and right
«button to enter IR control mode and select
the input channel in ascending and descending order respectively. The setting will be effective in a
couple of seconds.
Switch input port in descending order*
«Switch input port in ascending order*
SOURCE SELECTION
1 Switch the display channel at the
remote site to input port 1
SOURCE SELECTION
2 Switch the display channel at the
remote site to input port 2
SOURCE SELECTION
3 Switch the display channel at the
remote site to input port 3
SOURCE SELECTION
4 Switch the display channel at the
remote site to input port 4
Note
Right ( ) button to switch input source in ascending order (1, 2, 3, 4, 1, 2, ......)
Left ( ) button to switch input source in descending order (1, 4, 3, 2, 1, 4, ......)
Method B2: IR remote control for controlling the HDMI sources
Users can use the corresponding IR remote to control the HDMI source.
—
«
—
«
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 18 of 25

Default Custom Code — IR2 Code: 00 FF
Custom Code — IR3 Code: 0x12 0x21
Output 1 Output 2 Output 3 Output 4
Source 1 0xA1 0xB1 0xC1 0xD1
Source 2 0xA2 0xB2 0xC2 0xD2
Source 3 0xA3 0xB3 0xC3 0xD3
Source 4 0xA4 0xB4 0xC4 0xD4
Function
0x17
0x0A
0x0C
POWER
0x02
SOURCE SEL. 1
0x54 SOURCE SEL. 2 0x55 SOURCE SEL 3 0x56 SOURCE SEL. 4 0x01
F1
0x57 F2 0x58 F3
0x59 F4 0x06
Output Port 1
Input 1- 0x18 Input 2 - 0x5B Input 3 - 0x19 Input 4 - 0x07
Output Po2
Input 1 - 0x1B Input 2 - 0x5A Input 3- 0x1A Input 4 - 0x04
Output Po3
Input 1 - 0x0E Input 2 - 0x0D Input 3 - 0x12 Input 4 - 0x05
Output Po4
Input 1 - 0x1C Input 2 - 0x1D Input 3 - 0x1F Input 4 - 0x1E
IR Discrete Code
«
—
ACE PLUS CORP.
Headquarters :
9F-2., No. 190 Sec. 2 JungShing Rd.,Hsin-dian,
Taipei, Taiwan 231
TEL: [phone]
FAX: [phone]
Website: www.ace-plus.com
www.ace-plus.tw
Page 19 of 25