Cisco SOHO Series Original instructions

Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Regulatory Compliance and Safety Information
for Cisco 800 Series and SOHO Series Routers
This document provides international regulatory and safety compliance information for
Cisco 800 series routers and Cisco SOHO routers. Use this document with the other publications for the
Cisco 800 series or Cisco SOHO series router you have purchased.
This document contains the following sections:
•Safety, page 1
•Electromagnetic Compatibility, page 3
•EMC Class A Notices and Warnings, page 6
•Telecommunications, page 7
•Radio, page 10
•Declarations of Conformity, page 16
•Conformité Européenne (CE) Marking Directive, page 16
•European Union Statements, page 16
•California Perchlorate Contamination Prevention Act (Title 22, California Code of Regulations,
Chapter 33), page 17
•Translated Safety Warnings, page 17
•Obtaining Documentation and Submitting a Service Request, page 58
Safety
This section describes safety conditions and operating conditions for the Cisco 800 series routers and
Cisco SOHO routers. It contains the following:
•Agency Approvals and Standards
•Operating Conditions for Canada
•Operating Conditions for the European Community
•Operating Conditions for the United Kingdom

2
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Safety
•Power Cable and AC Adapter
Agency Approvals and Standards
The following safety standards apply to the Cisco 800 series routers and to the Cisco SOHO series
routers:
•UL 60950-1
•CSA 60950-1
•EN 60950-1
•IEC 60950-1
•AS/NZS 60950
•CCC
•NOM-019
Operating Conditions for Canada
In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on
page 17, the following operating condition applies to routers used in Canada:
The Industry Canada label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational, and safety requirements as
prescribed in the appropriate Terminal Equipment Technical Requirements documents. The Department
does not guarantee the equipment will operate to the user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities
of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. The customer should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any
repairs or alterations made by the user to this equipment, or equipment malfunctions may give the
telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility,
telephone lines and internal metallic water pipe system, if present, are connected together. This
precaution may be particularly important in rural areas.
Caution Users should not attempt to make such connections themselves, but should contact the appropriate
electric inspection authority, or electrician, as appropriate.
Operating Conditions for the European Community
The warnings and safety guidelines listed in the “Translated Safety Warnings” section on page 17 apply
to routers used in the European Community.

3
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Electromagnetic Compatibility
Operating Conditions for the United Kingdom
In addition to the warnings and safety guidelines listed in the “Translated Safety Warnings” section on
page 17, the following warnings apply to routers used in the United Kingdom:
Interconnection directly, or by way of other apparatus, of ports marked:
“Safety Warning—See instructions for use”
with ports marked or not so marked may produce hazardous conditions on the network, and that
advice should be obtained from a competent engineer before such a connection is made.
•The ports marked “Ethernet” and “Console” have a safety warning applied to them as follows:
“These ports do not provide isolation sufficient to satisfy the requirement of EN 41003; apparatus
connected to these ports should either have been approved to EN 41003 or have previously been
evaluated against B5E301 British Telecommunications plc (Post Office) Technical Guides 2 or 26
and given permission to attach; any other usage will invalidate any approval given to this apparatus.”
Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with
EN 41003:1993.
•This apparatus must be connected to a main socket outlet with a protective earth contact.
•Connection of power supply: The router is intended for use when supplied with power from a supply
providing 100 to 250 VAC, 50 to 60 Hz up to 0.5A.
Power Cable and AC Adapter
Warning When installing the product, please use the provided or designated connection cables/power
cables/AC adaptors. Using any other cables/adaptors could cause a malfunction or a fire. Electrical
Appliance and Material Safety Law prohibits the use of UL-certified cables (that have the “UL” shown
on the code) for any other electrical devices than products designated by CISCO. The use of cables
that are certified by Electrical Appliance and Material Safety Law (that have “PSE” shown on the
code) is not limited to CISCO-designated products. Statement 371.
Electromagnetic Compatibility
This section describes electromagnetic compatibility (EMC) compliance conditions for the Cisco 800
series routers and Cisco SOHO routers. It contains the following:
•Agency Approvals and Standards
•FCC Class B Statement
•CISPR 22 Class B Statement
•Canada Compliance Statements

4
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Electromagnetic Compatibility
•Australia Compliance Statement
•Statement 157—VCCI Compliance for Class B Equipment
Agency Approvals and Standards
This section lists the following agency approvals and standards for EMC:
•CFR47 part 15 subpart B, 2000 class B
•EN55022, 1998 class B, CISPR22, 1997 class B
•EN55024, 1998 Immunity Std, CISPR24, 1997 Immunity Std
•EN61000-3-2, Harmonics, EN61000-3-3, Flicker
•EN61000-4-2, Electro Static Discharge
•EN61000-4-3, Radiated Immunity
•EN61000-4-4, Electrical Fast Transients
•EN61000-4-5, Surge
•EN61000-4-6, Conducted Immunity
•EN61000-4-11, Dips and Sags
•AS/NZS 3548
•CCC
FCC Class B Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and the receiver
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution Modification of this equipment without Cisco’s authorization may result in this equipment no longer
complying with FCC requirements for Class B digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.

5
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Electromagnetic Compatibility
CISPR 22 Class B Statement
Emissions:
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information
Technology Equipment (ITE).
Canada Compliance Statements
Canadian Class B Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils
numériques de Classe B prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,”
NMB-003 edictée par le ministre des Communications.
Industry Canada Notice
This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications.
This is confirmed by the registration number. The abbreviation, IC, before the registration number
signifies that registration was performed based on a Declaration of Conformity indicating that Industry
Canada technical specifications were met. It does not imply that Industry Canada approved the
equipment.
Australia Compliance Statement
Network connected equipment is approved to the Australian and New Zealand Safety and EMC
requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New
Zealand. Stand-alone power supply modules provided with this equipment are separately approved by
an Australian State designated Electricity Authority.

6
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
EMC Class A Notices and Warnings
Statement 157—VCCI Compliance for Class B Equipment
EMC Class A Notices and Warnings
This section includes the following EMC Class A warnings for Cisco 888 and IAD881 models:
•Class A Notice for FCC
•CISPR 22 Class A Statement
•Canadian Class A Statement
•Statement 191—VCCI Class A Warning for Japan
Class A Notice for FCC
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Warning Modification of this equipment without Cisco's authorization may result in this equipment no longer
complying with FCC requirements for Class A digital devices. In that event, your right to use the
equipment may be limited by FCC regulations, and you may be required to correct any interference to
radio or television communications at your own expense.
Warning This is a Class B product based on the standard of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a
domestic environment, it may cause radio interference. Install and use the equipment according to
the instruction manual.

7
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Telecommunications
CISPR 22 Class A Statement
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class A Information
Technology Equipment (ITE).
Warning This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures. Statement 340
Canadian Class A Statement
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled "Digital Apparatus," ICES-003 of the
Department of Communications.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils
numeriques de Classe A prescrites dans la norme sur le materiel brouilleur: "Appareils Numeriques,"
NMB-003 edictee par le ministre des Communications.
Statement 191—VCCI Class A Warning for Japan
Telecommunications
This section describes telecommunications compliance conditions for the Cisco 800 series routers and
Cisco SOHO routers. It contains the following:
•Agency Approvals and Standards
•FCC Part 68 Notice
Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by
Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio
disturbance may arise. When such trouble occurs, the user may be required to take corrective
actions.

8
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Telecommunications
Agency Approvals and Standards
This section lists the following agency approvals and standards for telecommunications:
•FCC part 68 – TIA-968-A 2002, Addendum 3 2005
•IC CS-03, issue 9 2004
•R&TTE Directive 5/1999/EC, CTR3, TBR3
•AS/ACIF S002, S003, S006, S031, S043, C559
•IDA TS ISDN, TS ADSL
•IS 6100
•225-540-784, 225-540-788
•ITU I.430, ITU G.991.2, ITU G.992.1
Table 1 lists the Cisco 800 series routers that are not Telecom regulated because they only have Ethernet
ports or are only for Europe.
FCC Part 68 Notice
This equipment complies with Part 68 of the FCC rules and the Technical Requirements for Connection
to the Telephone Network published by ACTA. On the bottom of the this equipment is a label that
contains, among other information, the product identifier US:5B1MFNA0013 or US:5B1DLO1B0144.
If requested, this number must be provided to the telephone company.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical, the
telephone company will notify the customer as soon as possible. Also, you will be advised of your right
to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operation, or procedures that
could affect the operation of this equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications to maintain uninterrupted service.
If you have trouble with this equipment, please contact Cisco Systems for repair and warranty
information. If the trouble is causing harm to the telephone network, the telephone company can request
that you remove the equipment from the network until the problem is resolved.
Table 1 Cisco 800 Series Routers That Are Not Telecom Regulated
Models That Have Only Ethernet Ports Models That are for Europe Only1
1. These routers comply with the European requirements of CTR3/TBR3.
Cisco 806 Cisco 836
Cisco 831 Cisco 856
Cisco 851
Cisco 861
Cisco 871
Cisco 881
Cisco 881G

9
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Telecommunications
Normally, this equipment will be used in conjunction with FCC approved equipment that limits the
Encoded Analog Content that provides the required Billing Protection.
The facility interface and service order codes for the Cisco 800 series and the SOHO series routers are
shown in Table 2.
Cisco 800 series and SOHO series routers bearing labeling identification number US:5B1MFNA0013 or
US:5B1DLO1B0144, and Cisco 860 and 880 router models bearing labeling identification number
US:5B1ISO1B0247 comply with the following requirement:
•FCC Rules and Regulations 47 CFR Part 68
•TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone
Network, July 2001, as adopted by the Administrative Council on Terminal Attachments (ACTA).
Cisco 801, 802, 803, 804, 805, 806, 811, 813, 815, 826, 827, 828, 831, 836, 837, 851, 856, 857, 858,
871, 877, and 878 routers, and Cisco SOHO 76, 77, 78, 91, 96, and 97 routers bearing labeling
identification number US:5BMFMAM0013 or US:5B1DLO1B0144, and IAD881F, IAD881B,
C881SRST, , 888, 888G, IAD888F, IAD888B, C888SRST, routers bearing labeling identification
number US:5B1IS01B0247 comply with the following requirement:
•FCC Rules and Regulations 47 CFR Part 68
•TIA/EIA/IS-968, Technical Criteria for Terminal Equipment to Prevent Harm to the Telephone
Network, 2002, Addendum 3 2005, as adopted by the Administrative Council on Terminal
Attachments (ACTA).
Cisco’s Supplier Declarations of Conformity are available online at:
http://wwwin-tools.cisco.com/cse/prdapp/jsp/ExternalSearch.jsp?selNavObjId=search|extSearch
Table 2 Cisco 800 Series and Cisco SOHO Series Routers Facility Interface and
Service Order Codes
Port Type
Facility Interface
Code
Service Order
Code Jack Type
ISDN BRI S/T 02IS5 6.0N RJ-49C
ISDN BRI U 02IS5 6.0N RJ-49C
DSU 56K 04DU5-56 6.0N RJ-48S
ADSL Metallic — RJ-11C
SHDSL Metallic — RJ-14C
FXO 02LS2 None RJ-11C
FXO 02GS2 None RJ-21X
DID 02RV2.T AS.2 RJ-11C
Analog Modem 02LS2 None RJ-11C

10
Regulatory Compliance and Safety Information for Cisco 800 Series and SOHO Series Routers
OL-10260-02
Radio
Radio
This section describes radio compliance conditions for the Cisco 800 series routers and Cisco SOHO
routers. It contains the following:
•Agency Approval and Standards
•Power Level Settings
•Canadian Compliance Statement
•Statement 287—Declaration of Conformity to R&TTE Directive 1999/5/EC for the European
Community, Switzerland, Norway, Iceland and Liechtenstein
•RF Exposure
•Guidelines for Operating Cisco Wireless Access Points in Japan
•Administrative Rules for Cisco Wireless Devices in Taiwan
Agency Approval and Standards
The agency approvals and standards for 2.4 GHz radio are as follows:
•CFR47 part 15.247
•RSS-210 Rev 5
•ETSI EN 300.328.1
•ETSI EN301.489.1& .17
•RFS-29
•Japan Std 33a and Std 66
•EN 300.328-1
•EN 300.328-2
•EN 301.489-1
•EN 301.489-17
•EN 60950-1
•EN 50835
Caution The Part 15 radio device operates on a non-interference basis with other devices operating at this
frequency when using the integrated antennas. Any changes or modification to the product not expressly
approved by Cisco could void the user’s authority to operate this device.
Note This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to
certain frequencies and/or may require a license for operation. For more details, contact Cisco Corporate
Compliance.