ACI Farfisa Single Channel DVR User manual

STAND-ALONE DVR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
User manual VER 1.0
Thank you for purchasing our product.
Please read this user manual before
using the product.
Single channel
stand-aloneDVR
DIGITAL VIDEO RECORDER
DIGITAL VIDEO RECORDER
1 Channel Stand-Alone DVMR
ALL ABOUT IMAGE RECOGNITION & PROCESSING
Comply with Multiplexers
Best solution to replace Time Lapse VCR in use with Multiplexer
Single ChannelDigitalVideoRecorder

1 channelstand-aloneDVR
SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN!
CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space limitations.
The lightning flash with an arrowhead symbol within an equilateral triangle is intended to
alert the user to the presence of uninsulated “ dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to
presence of important operating and maintenance (Servicing) instructions in the
literature accompanying the appliance.
WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE UNITS NOT
SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
Attention: installation should be performed by qualified service Personnel only in
accordance with the National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF switches have power supplied to the
unit whenever the power cord is inserted into the power source ; however, the unit is
operational only when the ON-OFF switch is in the ON position. The power cord is the
main power disconnect for all unites.
29
2. Configuration of single channel stand-alone DVMR
3. Arrangement of RS-484 and RS-232C pic and RS-232C Hex-codes table
MENU ‘M’ SPEED ‘Q’ UP ‘U’
ENTER ‘E’ MARK ‘I’ DN ‘J’
PLAY ‘P’ P/T ‘T’ LEFT ‘H’
PAUSE ‘F’ RIGHT ‘K’
DEFAULT KEY ‘0’
Hex-code table :
Following ASCII codes are for programmers who want to control the DVMR unit via RS-232C port.
If you connect to RS-232C, you can operate DVMR unit using key board of PC, in addition to operation
using operation buttons on the front of DVMR unit. Send [Carrage Return : (13)] after you input every
code.
All ASCII-code are in 1 Byte format.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 7. Specification
Comm Port
1 5
6 9
Pin No. Division
1Alarm
2RS-232
3RS-232
4RS-485
5Common
6RS-485
7Relay out
8Relay out
9Relay out
Pin arrangement (Alarm/Relay out/RS-232C/RS-485)
Definition
Input
RxD
TxD
SD -
GND
SD +
N.C.
COM
N.O.
Alarm input : Pin #1 & #5
RS-232 : Pin #2, #3, & #5
RS-485 : Pin #4& #6
Relay out : Pin #8 & #9(N.O.)/Pin #8 & #7(N.C.)
RS-232C specification (baud rate/parity/data length/stop bit) : 19200, N, 8, 1

Table of Contents
1
1. About user manual …………………………………………………
2. Before reading this document ……………………………………
3. Unit description ……
4. Installation ……………………………………………………………
5. Operation ……………………………………………………………
3) Play ……………………………………………………………
4) Setting …………………………………………………………
7. Specification and configuration ………………………………………
1) Log-in …………………………………………………………
1) Front panel ……………………………………………………
2) Rear panel ……………………………………………………
Basic operation ……………………………………………
ALARM/MOTION SETUP ……………………………………
RECORD SETUP ……………………………………………
TIME/DATE SETUP …………………………………………
CAMERA SETUP ……………………………………………
DISPLAY SETUP ……………………………………………
TCP/IP SETUP ………………………………………………
MISCELLANEOUS SETUP …………………………………
1) Specification …………………………………………………
2) Configuration…………………………………………………
2
2
3
4
5
3
9
9
10
14
14
15
16
17
18
21
22
23
28
28
29
2) Record …………………………………………………………
12
6. HDD Bay ……………………………………………………………… 27
3) Arrangement of RS-485 and RS-232C pin ………… 29
1
2
3
4
5
6
7
8
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channel stand-alone DVR
7. Specification
28
1. SPECIFICATIONS
INPUT
OUTPUT
S/N RATIO
HORIZONTAL RESOLUTION
COLOR
ZOOM
SCREEN QUALITY
SPEED
COMPRESSED PICTURE
PICTURE PRESERVATION
METHOD
REC, MODE
TRACK PLAY
WEB INTERFACE
POST ALARM FUNCTION
BACK-UP
OTHERS
CAMERA CONTROL
CONFIGURATION
HDD
1 CH INPUT 1.0 VP-P, 75 OHM UNBALANCED (BNC TYPE)
2 OUTPUT VBS : 1.0VP~P.75 OHM UNBALANCED (BNC TYPE)
MORE THAN 4dB
500TV LINES
16.7 MILLION
LIVE & PB AVAILABLE
FULL : 720(H)X480(V) ACTIVE PIXELS
0.1~30 FRAME/SEC
JPEG
FIELD SWTCHER METHOD FULL SCREEN PRESERVATION
REAL-TIME/ TIME-LAPSE / EVENT
SEARCH, STILL
Single channel stand-alone DVMR
TCP/IP
1~59SEC, CONTINUOUS TIMING ESTABLISHMENT POSSIBILITY
PREVIOUS VCR, TIME LAPS VCR USAGE : VCR OUTPUT UTILIZATION
REMOTE BACK-UP USING TCP/IP
RS232C, RS485, MAX 4 ALARM INPUT
PAN/TILT/ZOOM AND FOCUS
REMOTE CONTROL : EXTERNAL EQUIPMENT, WIPER,PUMP,FAN
AND HEATER
PLUG&PLAY
VIDEO I/F
MONITORING
METHOD
RECORDING
/PLAY
FUNCTION
OTHER
FUNCTION
MODEL NO
OPERATION TEMPERATURE
OPERATION HUMIDITY
DIMENSION
WEIGHT
POWER SUPPLY
41F~ 104F (5C~ +40C)
LESS THAN 90%
BUILT-IN
19" RACK SIZE 1U , 44X434X360 mm
DC ADAPTER (12V DC 4.5A)
MECHANICAL
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 7. Specification
HDD, EIDE, LBA MODE, UP TO 140 GB/UNIT, UP TO 2 HDDsMEDIA
INTERNAL1 OR 2 HDD
OPTIONAL HDD BAY SUPPORT
6HDD/1UNIT, MAX 22 UNITS/UNIT
POSSIBLE HDD MIX USGE OF DIFFERENT MANUFACTURER
IR REMOTE CONTROLLER
APPROX. 6.8KG (STANDARD EXPORT PACKAGE)

2. Before reading this document
1. Thisdocument isintended for both the administrator and users of stand-alone DVRunit.
2. Thismanual contains information for configuring, managing and using stand alone DVRunit.
4. Be sure to read thismanual beforeusing stand alone DVRunit.
3. To prevent fire or electrical shock, do not expose the product to heat or moisture.
1. About user manual.
2
Beforeinstalling stand-alone DVR,be sure to carefully read and follow instructions in this
User manual. Pay particular attention to the parts that are marked NOTICE.
Also, when connecting with external devices, first turn off the power OFF and follow manual
instruction for proper installation
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channelstand-aloneDVR
5.For question and technical assistance of this product, contact your local dealer.
Strong recommendation on installation ofthe DVRunit
1. Check electricityat the place you want to installthe DVRunitifitisstable and meetsour electricity
requirements.
Unstable electricity will cause malfunction of the unit or give critical damage to the unit.
2. Several chips on the main boardof the DVRunitand harddisk drive inside the unitgenerate
heat, and it must be properly discharged.
Do not put any objects just beside exhaust port(fan) on the right side of the unit and do not close
up an opening (fresh air in-take) on the left side of the unit..
3. Put the DVRunitatwell-ventilated place and do not put heat-generating objectson the unit.
When it is installed inside 19 inch mounting rack together with other devices, please check built-
in ventilation fan of the rack is properly running.
6. HDD BAY
27
Default HDD installed in DVMR unit
1) 1~2 HDDs as per customer requirements
3) HDD capacity : Up tp 120GB/unit
Compatibility with up to 120GB confirmed
HDD Bay ( Tera-Tray )
In case up to 2 HDDs installed in a DVMR unit is not sufficient and needs to increase storage capacity,
connect HDD Bay to DVMR unit.
TM
DVMR unit
HDD Bay
DVMR UNIT
Teratray-04 40 pin HDD
cable
Total HDDs : 6 HDDs
2) Very economical way to expand storage capacity
Models of Tera-Tray
TeraTray-04 : Includes up to 4 HDDs
TeraTray-10 : Includes up to 10 HDDs
TeraTray-20 : Includes up to 20 HDDs
TM
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 6. HDD BAY
1. HDD EXTENSION
2. HDD BAY
1) Configuration of Bay connection to DVMR unit
If each of 22 HDD is 120 GB in capacity, total HDD capacity connected to a unit of DVMR unit is 2.6 TB.
We can add huge capacity of HDD space to a unit of DVMR just at the price level of normal EIDE HDD.
2) EIDE, 3.5 inch, 7200 rpm, LBA mode type
Notice : To connect HDD Bay to DVMR unit, first turn off power to both DVMR unit and HDD Bay.
Then turn on power to HDD Bay first and then DVMR unit after more than 5 seconds.

1. POWER SWITCH WITH LED : DC power switch with LED
2. LED : Represents status of operation
3. MENU : Used when changing the menu of SYSTEM SETUP
4. ENTER : Selects items in the menu
5. PLAY : Starts playback
6. PAUSE : Pauses display screen in playback
7. SPEED : Assigns playback speed
10.Remote controller sensor input window
3. Unit description
Notice : If input window is covered by some object, the remote controller may not work.
3
Notice : If several buttons are simultaneously or incorrectly pressed, the system may
not function correctly.
MENU PLAY P/TMARKSPEED
ENTER
8
76
5
4
310
1
POWER OVERWRITE
RECORD
PLAY
SETUP
2
PAUSE
911
31
24
1) Front panel
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVR 3. Unit description
MARK IMAGE SETUP6
1) While you see pictures replayed, press [MARK] button. You will see “PAUSE”and “SPD”displayed.
2) Using button, move as many as you want to mark, and then press [MARK] button.
3) Pictures between 1st [MARK] button and 2nd [MARK] button are all marked and stored separately on HDD.
If HDD space assigned for marked image is full, “FULL”is displayed and [MARK] button doen not work.
5) To play marked images, select PLAY IMAGE, and to delete marked images slect DELETE IMAGE.
Notice : HDD CLEAR command does not clear marked images, and DELETE MARK IMAGE command
just delete marked images.
(HDD space for marked imaged : The system arranges automatically, and it corresponds to space
for recording 10 minutes in maximum recording rate.)
MARK IMAGE function is very useful, because it protects marked images from being overwritten.
During palyback, you can mark images to store them on HDD safely free from being overwritten after HDD
starts to overwrite.
PRODUCT ID : Serial number of product. Necessary for manufacturer to know manufacturing date,
program version number, and others.
7
2) HDD AUTO DETECT : Allows to detect HDD just in case first HDD search after purchase failed
MARK IMAGE SETUP
SELECT , PRESS ENTER
TOTAL FRAME 0
START TIME
/ / : :
END TIME
/ / : :
PLAY IMAGE
DELETE IMAGE
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
Numbers of images
on HDD
Delete or play only
marked images
HDD DATA LIST
SELECT , PRESS
SIZE
TYPE
FRAME
START
END
POS
NUM
Display of HDD DATA LIST
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
: 61.4GB , 53.9GB
: NORMAL
: 398947
: 02/04/07 07:40:38
: 02/04/07 14:11:56
: IN-DVR
: 1ST MASTER
Start and end of recording
Number and location of
HDD
>
26
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
HDD space. Used space
Start and end of
data recorded
Display of MARK IMAGE
SETUP
4) If you mark many images, instead of choosing image by image, cancel PAUSE by pressing
[PAUSE] button in step 1). Images are replayed in normal speed. Then press [MARK] button to end mark images.
9. P/T : Control PAN/TILT/ZOOM camera
11. Direction buttons : To move in the SETUP menu selection, change direction of playback
or play a role of number keys from 1 to 4 when entering password
8.MARK : Mark images in playback mode to protect marked images from being overwritten

4
8. I/O : RS-232C, Sensor input/Relay output
Notice : When connecting with other applications, be sure to turn off the system.
Notice : Improper power connection toDVRunitwilldamage the system.
1. TERATRAY CONNECTION : Connects to HDD Bay(Tera-Tray)
2. TRIGGER : Connects to trigger output of multiplexer(recording syncronize)
3. ETHERNET:Connects toLAN,WAN,or Internet toaccess DVRunitvia IPnetwork
4. CAMERA : Connects to camera
5. LOOP : Loop out
6. VCR : Connects to VCR for backup
7. MONITOR : Connects to monitor
9. DC 12V : DC 12V connection port
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-aloneDVR3. Unit sedcription
2) Rear panel
ETHERNET
1 2
8
TRIGGER
rks
TERATRAY CONNECTION CAMERA
LOOP
VCR
MONITOR DC 12V
Com m Port
I/O
3
4
5
6
79
25
3. Example of schedule setting
4. Note for schedule recording :
01:00-03:00 ON
04:00-05:00 ON
1
2
3
Just record from 1 to 3 and from 4 to 5, and does not record for the rest of hours.
01:00-03:00 OFF
04:00-05:00 OFF
Just not record from 1 to 3 and from 4 to 5, and record for the rest of hours.
01:00-03:00 ON
04:00-05:00 OFF
Just record from 1 to 3 and not record for the rest of hours(In case ON and OFF are exists, the
system give priority to ON.
PANTILT COMMAND SETUP
SELECT , PRESS ENTER
Display of PANTILT COMMAND
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
4
HDD INFORMATION
5
1) HDD DATA LIST : Show general information of HDD
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
If you set scheduled recording, DVMR unit does not record before the set time. It only starts recording
at START time and ends at END time.
PANTILT CMD SETUP : If you want to connect PTZ camera which is not included in the list of PTZ
camera, you have to input protocol of PTZ camera you are going to connect to DVMR unit.
You can input protocol of PTZ camera you are going to connect in USER DEFINE SETUP
For details, refer to Manual for incorporating PTZ protocols.
DRX-502A
485 BAUD : 9600
USER DEFINE SETUP
>
1. USER DEFINE
2. DRX-502A
3.AECD-2000
4. HMC250
5. PELCO D type
1200
2400
4800
9600
19200
By pressing [ENTER] button, you can select type of PTZ camera and also baud rate of RS-485 communication

4. Installation
1) Camera connection
Connect camera to the CAMERA INPUT on the rear panel of the system.
2) Monitor connection(Composite type)
Connect the monitor to the MONITOR OUT on the rear panel of the system.
5
VIDEO
LENS
VIDEO
DC
AC24V/DC12
V.P
DC
LEVEL
Rear view of camera
VIDEO A
IN OUT
VIDEO C
IN OUT
VIDEO B
IN OUT
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channelstand-aloneDVR
4. Installation
TIME/DATE INPUT
DAY OF THE WEEK
24
RESET: NONE
SELECT , PRESS ENTER
Display of SCHEDULE REC SETUP
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION
SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
START ―END ON/OFF
00 : 00 ―24 : 00 ―――
START ―END ON/OFF
00 : 00 ―24 : 00 ―――
SCHEDULE REC SETUP
3
Records according to schedule by day or day of the week. Two time spans can be set for a day and a day of
the week respectively. In total, 4 spans of recording or not recording can be set in a day.
1) Recording schedule for a day : Record during set time in set day
Setting of time/minutes is done by pressing [ENTER] button, and it increased in the unit of
30 minutes per pressing [ENTER] button.
(1) Select date : Select recording date using button.
(3) ON/OFF selection : After completing input of schedule, choose ON or OFF using [ENTER] button.
ON indicates to record and OFF means not to record.
(5) In RESET mode, you can delete recording schedule.
(6) Press [MENU] button to leave SCHEDULE REC SETUP.
(NONE : Input time/date DATE : Delete schdule of selected data ALL: Delete all schedule)
Using button, move to the date to delete, and press [ENTER] button to delete.
Press [ENTER] button to delete all recording schedule.
(2) Select time : Enter into setting mode by pressing [MARK] button.
Using direction button, set time to start recording and time to end recording.
Select data
Select time
RESET mode
(Notice) Changing is possible just “RESET : NONE” is displayed.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
(4) After completing to set schedule, press [MENU] button to leave.
2) Recording schedule for a day of the week : Set time for each day of the week as procedure for
recording schedule for a day.
Notice : ThisDVRsystem automaticallydetectsvideo system of camera you connected
to the unitwhen you boot DVRsystem first.Itisnot necessaryto set video
systemseparately, and DVRsystem set at NTSCor PALsystem automatically
when you boot the system.
Notice : Connect cameras and monitor to DVRunitwhileDCpower switch on the front
panel is off.
Com m Port
I/O
DC 12V
CAMERA
LOOP
VCR
MONITOR
Co m m Port
I/O
DC 12V
CAMERA
LOOP
VCR
MONITOR
> DATE : 02―04―7 SUN
TIME/DATE INPUT SETUP

3) Monitor(S-VHS) connection
Connect S-VHS monitor to MONITOR OUT(S-VHS) on the rear panel of the system.
6
VIDEO PRINTER
VCR
4) TRIGGER connection
Connects to TRIGGER port of MULTIPLEXER if your multiplexer has TRIGGER OUT, in
case you replace time lapse VCR used in connection with multiplexer.
***** Replacing Time Lapse VCR in use with Multiplexer *****
This DVRunit can replace time lapseVCRused inconnectionwith multiplexer.
Ifyouwantto use thisDVRunitinconnectionwith multiplexer, set followings
in RECORDSETUPin SETUPofDVRunit.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-alone DVR
4. Installation
RECORD SPEED : From 002Hr to 960Hr
MUX/REC:Select MUX/RECwhen you want to use thisDVRin connection with multiplexer,toreplace
time lapse VCR.
MUX CH NUMS : numbers of cameras connected to multiplexer(from 1 to 16)
Set speed : 002Hr 004Hr 006Hr--------------- 072Hr------------------------- 960Hr
Tape recording hour : 2 4 8 ------------------ 72 ----------------------------- 960
(with 2 hrs tape) real time 72 hrs mode 960 hrs mode
8. MISCELLANEOUS SETUP
1) Using button, select item to be changed and press [ENTER] button to be ready for changing
23
1
2
BUZZER SETUP : Sets buzzer ON/OFF.
ID/PW SETUP : Sets User ID and PASSWORD
Default setting :
ADMIN의PASSWORD : 1 ( )
USER PASSWORD : 2 ( )
2) Using button, enter current number first and enter new number. Numbers must be equal or
less than 8 digits, and each digits must be from 1 to 4.
Change PASSWORD to your own one as soon as this product is installed
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
31
24
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
MISCELLENEOUS SETUP
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
SELECT , PRESS
1
2
3
4
5
6
ID/PW SETUP
SELECT , PRESS ENTER
ID
CURRENT
NEW
CONFIRM
< USER >
< >
< >
< >
PW
PW
PW
1,2,3,4 : INPUT PASSWORD
MARK : ERASE PASSWORD
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
Display of ID/PW SETUP
Display of MISCELLENEOUS SETUP
You can set each group of BUZZER at ON or OFF independently.They are SYSTEM, BUTTON, ALARM,
MOTION, and LOSS.
Co m m Port
I/O
DC 12V
CAMERA
LOOP
VCR
MONITOR

5) Network connection
Connects to HDD Bay(Tera-Tray), Multiplexer, or Network
Notice : TERATRAY CONNECTION is only for HDD Bay, Tera-Tray. It can not be connected with
any other devices. Also, when electric contact is applied while power is on, it may
damage the system.
ETHERNETTRIGGER
rks
TERATRAY CONNECTION
Connect to
HDD BAY Connect to multiplexer
6) HDD connection
7
HDD2
(SLAVE)
HDD1
(MASTER)
MAIN BOARD
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-aloneDVR
4. Installation
Be sure to set jumper setting for each HDD as per HDD manufacturer’s specification.
If you install single HDD, it must be at Master, and HDD1 is at Master and HDD2 is at Slave
in case you install2 HDDsin a unitof DVR.
22
7. TCP/IP SETUP
TCP/IP SETUP
IP ADDRESS
GATEWAY
SUBNET MASK
MAC ADDRESS
DHCP SETUP
SELECT , PRESS
1
2
3
4
1
2
IP ADDRESS : Move using button and change numbers using button.
GATEWAY : Move using button and change numbers using button.
4
3SUBNET MASK : Move using button and change numbers using button.
MAC ADDRESS : It is unique ID number provided by DVMR manufacturer, and the user must not change
under any condition. When modified, it can cause collision with other systems in the Internet line and cause
problem in operation. Make sure this number remains unchanged always.
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
(DEFAULT valuce : 192, 168, 001, 100 8000)
(DEFAULT value : 192, 168, 001, 001)
(DEFAULT value : 255, 255, 255, 000)
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
DHCP SETUP : If you press ENTER button, you can enter into sub-menu of DHCP SETUP. In this
menu, you can select DHCP or MANUAL by pressing ENTER button. If you set
IP DETECT MODE at DHCP, DVMR unit automatically connects to IP network during
the process of booting and you see IP information if you enter REQUEST IP.
You have to memorize this IP information and input this information into SETTING of
Remote viewer program installed on your PC (client PC).
If it fails to connect automatically or you set IP DETECT MODE at MANUAL, you have
to get IP information by executing ipconfig or winipcfg in the client PC from which you
want to access to DVMR unit, to assign IP information for DVMR unit.
5
5
TCP/IP option of stand-alone DVMR enables users to see live pictures and search recorded pictures via IP
network, far apart from DVMR unit. It is also possible to control PTZ camera while you see live pictures.
To see live pictures or search recorded pictures, users must assign static IP address to DVMR together with
Gateway and Subnet mask, and install Remote Viewer program in client PC from which you are going to
access to DVMR unit. For detail procedure for installing Remote Viewer program and settings, refer to Remote
Viewer Program manual on CD included in the package.
In case port number of 80 is protected by firewall, change port number to other one not protected by firewall.
Connect to
IP network
In case you replace HDD, you have to clear all data on HDD and set at FACTORY
DEFAULTonce. Itisnot necessaryto format HDDbefore installation, and DVRsystem
automatically detects HDDs and format before recording.
HDD1
HDD2

7) Power connection
9) Detail setup in SYSTEM SETUP
For detail setup, refer to the instruction of SYSTEM SETUP.
Connect the power to the POWER CONNECTION on the rear panel of the system, and
turn on the switch.
8) Turn on the POWER and Log-in the the system
Follow direction in the Log-in part of this manual to input the PASSWORD and start the system.
8
DC 12V
Factory default password for account manager is “1”, and “2”for user.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-alone DVR
4. Installation
6. RECORD SETUP
1
2
HDD CLEAR : If YES is selected, it deletes contents of the HDD.
Notice : Be careful to delete data on HDD, because you can not recover deleted data.
21
RECORD MODE
31) TIMER : Records at a certain time interval set at RECORD SPEED.
2) TIMER+ALARM : Combination of TIMER and ALARM. If alarm is activated, the system
records at its maximum recording rate(60 FPS) for ALARM DURATION.
4) MOTION+ALARM : The system just records when motion is detected, and records when alarm
is activated for ALARM DURATION at 60 FPS.
3) MOTION : The system records just when motion is detected for MOTION DURATION.
RECORD SPEED : Adjust recording frame rate. 0.1 indicates 1 field per 10 second.
4(Select any one among 60/30/15/10/5/2/1/0.5/0.2/0.1 FPS)
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
HDD CLEAR
HDD FULL
RECORD MODE
RECORD TYPE
RECORD SPEED
PRIORITY MODE
Using button, set HDD CLEAR at YES and press [MENU] button.
You will see messages on the right, and then press [ENTER] button to delete all image data on HDD.
5) MUX/REC : Select when you use this DVMR in connection with multiplexer, replacing time lapse VCR.
<CAUTION>
IF YOU WANT TO DELETE
PRESS <ENTER> KEY
MUX CH NUMS : When you use this DVMR unit in connection with multiplexer, replacing time lapse VCR,
set numbers of camera connected to multiplexer.
5
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
RECORD SETUP
HDD CLEAR
HDD FULL
RECORD MODE
RECORD SPEED
MUX CH NUMS
SELECT , PRESS
: NO
: OVERWRITE
: TIMER
: 60FPS
: 16CH
1
2
3
4
5
>
Display of RECORD SETUP
Tape recording hour : 2 4 8 72 960
(based on 2 hrs tape)
HDD FULL : You can select OVERWRITE or STOP RECORDING using button. When HDD is full, the
system deletes old data to record current pictures, if you set at OVRWRITE. It stops and shows warning message
when it is full, if set at STOP RECORDING.
If you selected MUX/REC in RECORD MODE, you are requested to select record speed from 001
to 480. This is to synchronize with switching time of multiplexer, that is, recording hour of tape
in former time lapse VCR.
Set speed : 002 004 006 ------------------ 072 -------------------------------------960

5-1. Log-in
1. Log-in
9
3) Use button to enter password that has 1 to 8 digits with numbers from 1 to 4.
4) Use [MENU] button to change.
1) Press [MENU] button to enter the system menu after starting the system.
2) LOGIN DVR SYSTEM window appears as shown above.
- Factory default password is as below.
ADMIN(Adminstrator mode) : “1”USER (User mode) : “2”
NOTICE : We recommend you to enter your own password as per procedure in 5-4)- - (page.23)
8
5) After entering the password, press [ENTER] button to go back to the system menu.
NOTICE : When logged into USER MODE, only DISPLAY SETUP and TIME/DATE TYPE SETUP is
possible.
2
31
24
LOGIN DVR SYSTEM
PASSWORD < >
: INPUT PASSWORD
: ERASE PASSWORD
: ENTER OR EXIT
1,2,3,4
MENU
ENTER
NOTICE : Be sure to memorize the changed password.
- If password entered matches previously set number, “ADMIN GRADE LOGIN OK”message appears.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channel stand-alone DVR 5. Operation
Enter the password
default P/W : 1
1
Input or modify
2
If password entered does not match previously set number “CURENT PW INPUT ERROR”message
displayed.
NOTICE :To protect hard drive from damaged, turnoffthe power switch of DVRunitafter you first
press [MENU]button. Ifyou press [MENU]button, DVRunitstops recording, and HDD
head is not in the process of writing.
20
MOTION MASK SETUP : Sets detection area in picture taking area.
4
SELECT VER LINE : Select all cells in a vertical line.
SELECT HOR LINE : Selects all cells in a horizontal line.
CLEAR BLOCK : Delete BLOCK
SELECT ALL CELLS : Select all cells in area shown.
CLEAR ALL CELLS : Delete all cells.
1) Press [P/T] button to choose desired EDIT mode.
2) Use direct buttons to assign BLOCK and [ENTER] button to set.
3) MASK area in green color is detection area and the rest is no detection area.
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
EDIT : SELECT EACH CELL
<P/T> : CHANGE EDIT
<ENTER> : MASK ON/OFF
ON
Shows cell to be
set
Display of MOTION MASK SETUP
4) Detection area is indicated in green and no detection area is in colorless.
SELECT EACH CELL : Select cell by cell.
SELECT AREA : Select areas.
SELECT BLOCK : Select BLOCK When [ENTER] button is pressed, “ON” is
displayed in the first line(MODE) of the
screen.
Then move using direction buttons to set.
Shown when
setting blocks
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation

5-2. Recording
10
1. PLAY
2. P/T
2002 / APR / 01 AM 04:34:54
60FPS REC
(MOTION REC )
(001MUX REC)
CAM1
Indicates current time
Recording basic screen(TIMER recording)
Changes to Playback Mode from Recording mode.
Refer to Playback part(PAGE.13)of this manual
2) Use button to choose the ADDRESS of the
1) Press [P/T] button.
P/T camera.
Display of PAN/TILT Control
(Example : DRX-502A)
3) Use button to select the commend for
P/T camera.
5) Press [P/T] button to come back to recording screen.
4) With [ENTER] button, select ON/OFF.
2002 / APR / 01 PM 01:00:00
60FPS REC
CAM1
CAM : 001 FOCUS FAR
EXIT : PRESS [P/T]
1. Indicate address of P/T
camera : 001~255
2. Command
FOCUS FAR
FOCUS NEAR
FOCUS AUTO
PAN RIGHT
PAN LEFT
TILT UP
TILT DOWN
ZOOM IN
ZOOM OUT
AUTO PAN
LIGHT CMD
WIPER CMD
PUMP CMD
POWER CMD
FUNTION 1
FUNTION 2
FUNTION3
3. Set ON/OFF for selected
command
ON/OFF (ENTER button)
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-alone DVR5. Operation
Indicate recording speed.
60FPS : Records 60 fields/sec
MOTION REC : Records when motion is detected
001MUX : Records in connection with multiplexer
REC : Represent current mode is
on recording.
1. SORT : Originally the list shown is arranged in the sequence of date and time. If you press
[ENTER] button, list shall be rearranges in the sequence of ALARM, LOSS, and MOTION.
2. DELETE : When DELETE is selected, you can enter into any one of MARK, PAGE, ALL.
19
SENSITIVITY : Adjust motion detection sensitivity in 5 steps.
VERY LOW – LOW -- NORMAL -- HIGH — VERY HIGH
DETECT CELL : Defines size of objects to be detected. The smaller DETECT CELL, smaller object can be
detected. Can choose from 1 to 20. If DETECT DELL is set at 5, motion detection is activated
only in case 5 DETECT CELLs are simultanuously activated.
MOTION REC DURATION : Sets recording time when a motion is detected.
Set value from 1 sec to 3 minutes according to frequency of motion in
picture taking area.
1) DATE/TIME : Order in data and time 2) ALM : Order in type (ALARM, LOSS, MOTION)
Move to any one of 3 using button and press [ENTER] button to enter.
3MOTION SETUP :
1) MARK : Delete selected item in the list.
2) PAGE : Delete all item in the current page.
3) ALL : Delete all items in the list.
- Move using button, and select using [MARK] button(*).
3. GOTO : Starts playback from marked item in the list.
- Move to an item in the list using button, and press [MARK] button.
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
FACTORY DEFAULT value is 1 sec.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
SELECT , PRESS
SENSITIVITY : NORMAL
DETECT CELL : 001
RECORD TIME : 1 SEC
MOTION SETUP
>
Display of MOTION SETUP
- For details, refer to manual for incorporating protocols for
PAN/TILT camera.

11
3. Sensor recording
Refer to REC MODE SETUP in 5 -4 - 5 - (RECORD SETUP) in page 21 for more detail of TIME+ALARM OR
MOTION+ALARM and ALARM SETUP 5- 4- 5 - in page18(alarm setup) for more detail of ALARM
DURATION.
5. Recording by MOTION DETECTION
Refer to ALARM/MOTION SETUP in 5- 4- 5 from page 18
to 20. It must be set at MOTION or MOT+ALM to record
whenever motion is detected.
1) When there is sensor input, recording starts. 2) It records for preset period of time.
For more details, refer to SCHEDULE REC SETUP in MISCELLANEOUS SETUP in 5- 4- 8 - in page 24
4. Scheduled recording
3
1
3
6. Attention
1) Recording is stopped during SYSTEM SETUP.
2) Recording is stopped during playback or when in SEPUP
menu.
3) Recording is not possible if no camera is connected.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-aloneDVR5. Operation
RECORD SETUP
HDD CLEAR
HDD FULL
RECORD MODE
RECORD SPEED
MUX CH NUMS
SELECT , PRESS
: NO
: OVERWRITE
: MOT+ARM
: 60FPS
: 16CH
MOT+ALARM : Records when motion detected or when alarm is activated for preset duration time in above example.
>Or set at
TIM+ARM
ALARM SETUP
ALARM SIGNAL
> ALARM DURATION
SELECT , PRESS
: N.C
: 20 SEC
Set duration of
alarm
1
2
Records as scheduled, and setting can be done by date or by day of the week.
For each day, 2 different time intervals can be set at ON or OFF in the unit of 30 minutes, and same for each
day of the week. Therefore users can set 4 recording time intervals of recording or not recording for every day.
RECORD SETUP
HDD CLEAR
HDD FULL
RECORD MODE
RECORD SPEED
MUX CH NUMS
SELECT , PRESS
: NO
: OVERWRITE
: MOTION
: 60FPS
: 16CH
>or
MOT+ARM
Display of RECORD MODE
5. ALARM/MOTION SETUP
1ALARM SETUP : Sets type of sensors connected to DVMR unit.
OFF : Not in use.
NC : Normal closed. When an event happens, contact is opened.
NO : Normal open. When an event happens, contact is closed.
ALARM DURATION : Duration of recording when an ALARM is activated.
18
2
ALARM SETUP
> ALARM SIGNAL
ALARM DURATION
ELECT LIST TYPE
SELECT , PRESS
: N.C
: 20 SEC
: ALM
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
ALARM LIST SETUP
SELECT , ENTER , MARK
DATE
> --/--/--
--/--/--
--/--/--
--/--/--
--/--/--
TIME
--/--/--
--/--/--
--/--/--
--/--/--
--/--/--
ALM
--/--/--
--/--/--
--/--/--
--/--/--
--/--/--
SORT DELETE GOTO
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
A: ALARM
L : LOSS
M : MOTION
Playback from GOTO
time
(set time : 10, 20, 30, 40, 50 sec, 1 MIN, 3 MIN, 5 MIN)
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
Using button, move to any of SORT/DELETE/GOTO
Display of ALARM LIST SETUP
Display of ALARM SETUP
ALARM LIST SETUP : Shows list of alarms up to 400. If total alarm exceeds 400, it overwrites from
the beginning. Alarm list is very useful to manage DVMR system, in case it is in use in connection
with alarm sensors.
SELECT LIST TYPE : “A” indicates Alarm, “L” indicates Loss, and “M” indicates Motion.
You can select group of events, NONE, A, L, and M, by pressing [left] and
[RIGHT] buttons. If you select NONE, no event list shall be provided.

2) After [PAUSE] button, press button to advance picture by picture in both direction. It is useful
to check one after the other carefully.
1. How to replay
1) Press [PLAY] button to begin playback.
2) Screen on the right will appear.
3) Press [PLAY] button to start playback
from the first of recorded data.
2. GOTO time settings
1) Select G(GOTO) submenu and move cursor using key to set.
2) Using key, set year, month, date, time at which you want to to start.
(To start from a specific time, first set the
GO TO time before press [PLAY] button)
3) Press [PLAY] button to start playback.
NOTICE : During playback or settings in SETUP menu, recording is stopped.
3. Pausing and advancing picture by picture
1) During playback, press [PAUSE] button to pause. Press once more to play again.
12
NOTICE : When value out of range of start and end of data entered, it starts from START time.
S : 2002/APR/07 AM 07:40:38
E : 2002/APR/07 PM 02:11:56
G : 2002/APR/07 AM 00:00:00
2002 / APR / 01 AM 04:34:54
STOP
Indicates
recording is
stopped
: Cursor
S (START) : Start of recording
E (END) : End of recording
G (GOTO) : Set time from which
playback starts
NOTICE : When value is in the range of START and END, but there is no recorded picture at the set time, it moves to the closest time
of the recorded picture.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-alone DVR
5. Operation
5-3. Play
Display of Playback
4. TIME/DATE SETUP
2SET TIME/DATE TYPE : Sets notation of TIME/DATE
1. HOUR DISPLAY : Choose AM/PM type or 24 hours time indication
2. DATE DISPLAY : Select Asian type, American type, or European type.
3. MONTH DISPLAY : Choose indication of MONTH in Alphabet or Number
17
SET TIME/DATE
YEAR
MONTH
DAY
HOUR
MINUTE
SECOND
SELECT , PRESS
2002/APR/15
PM 09:23:17
Display of SET TIME/DATE
1SET TIME/DATE : Sets year/month/day/hour/minute/second
With button, move to year/month/day/hour/monute/second, and change value
using button.
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
SET TIME/DATE
SET TIME/DATE TYPE
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
SET TIME/DATE
SET TIME/DATE TYPE
TIME/DATE TYPE SETUP
HOUR DISPLAY
DATE DISPLAY
MONTH DISPLAY
SELECT , PRESS
: AM/PM
: ASIAN
: ENGLISH
Display of TIME/DATE TYPE SETUP
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation

5. MARK IMAGE SETUP
4. Playback speed setup
1) During playback, press [speed] button.
2) Screen on the right will appear.
3) Set direction of playback using key.
4) Set speed of playback using key.
(High speed up to x60 and slow speed up to
1 field/60 sec are available)
You can store some pictures very specially if you press [MARK] button during palyback. Pictures between you
first press [MARK] button and you press [MARK] button again shall be protected from being overwritten when
HDD is full. And it is very useful feature to utilize some important pictures to be safe from being deleted by mistake.
13
Press
1X PLAY SPEED
2X PLAY SPEED
4X PLAY SPEED
8X PLAY SPEED
16X PLAY SPEED
32X PLAY SPEED
60X PLAY SPEED
Press
1X PLAY SPEED
1/2 PLAYSPEED
1/4 PLAYSPEED
1/8 PLAYSPEED
1/16 PLAYSPEED
1/32 PLAYSPEED
1/60 PLAYSPEED
2002/APR/12 AM 07:40:38
1X PLAY SPD
CAM1
Indicate playback speed
Represent [SPEED]
button is pressed
MARK IMAGE SETUP
SELECT , PRESS ENTER
TOTAL FRAME 0
START TIME
/ / : :
EMD TIME
/ / : :
PLAY MARK IMAGE
DELETE MARK IMAGE
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
Refer to MARK IMAGE SETUP in MISCELLANEOUS SETUP in 5-4)- - in page 28
86
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-aloneDVR5. Operation
Play just marked
pictures or delete
marked pictures
Display of MARK IMAGE SETUP
3. CAMERA SETUP
1
2
TITLE SETUP : Input title of camera.
COLOR BAR TEST : Displays COLOR BAR CHART.
Press [ENTER] button then move to any location you
want using button, and then select letters using
button.
After complete to change, press [MENU] button to
return to main menu.
16
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
CAMERA TITLE SETUP
SELECT , PRESS ENTER
0 1 2 3 4 5 6 7 8 9 . , < > ( ) - = A B C D
E F G H I J K L M N O P Q R S T U V W X Y Z a b
c d e f g h I j k l m n o p q r s t u v w x y z
> CH1 < CAM 1 >
Display of CAMERA TITLE SETUP
Use to adjust colors of monitor.

1. Start of SETUP
1) Press [MENU] button.
2) Log into the system by entering password.
3) Select SEPUP item using button
4) Press [ENTER] button to enter submenu of selected SETUP item.
5) Select SEPUP item in submenu using button, and change value using button
6) Press [ENTER] button to select SEPUP item, and press [MENU] button to go back to
previous menu.
14
SYSTEM SETUP
SELECT UP/DOWN , ENTER
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
7) If you choose FACTORY DEFAULT, all settings shall be changed to settings done by manufacturer,
and we recommend you to set at FACTORY DEFAULT in the first operation, or when
you replaced EPROMfor upgrading DVRprogram or replaced HDD.
You can set all group of settings at FACTORY DEFAULT as a whole or group by group.
If you want it as a whole, set ALL SET at ON by pressing [ENTER] button, and set ALL SET at OFF
and set each group of FACTORY DEFAULT at ON or OFF independently by pressing [ENTER] button.
After you decide ALL SET or group by group set, move to RESET NOW and press [ENTER].
SETUP items remain unchanged even though you choose FACTORY DEFAULT
1. Time and date of TIME/DATE SETUP 2. All recorded data on HDD
3. Marked data 4. ADMIN password
5. ALARM LIST SETUP
NOTICE :Inthefirst operationofthis DVR, we recommendusersto setatFACTORY DEFAULTbeforeyouselect variousparametersof
operation.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channelstand-aloneDVR 5. Operation
5-4. SETUP
Display of SYSTEM SETUP
2. DISPLAY SETUP
: If TIME and DATE is on, time and date of recorded pictures is displayed in playback.
DISPLAY SETUP
TIME/DATE
CAMERA TITLE
PB TIME/DATE
PB CAMERA TITLE
DVR STATUS
SELECT , PRESS
: ON
: ON
: ON
: ON
: ON
1
2
3
4
5
This is about the contents displayed on the display screen.
2002/ARP12 AM 07:40:38
60FPS REC
CAM1
15
1
2
: If TIME/DATE in on, time and date is indicated on live screen.
: If CAMERA TITLE is on, camera title is displayed on live screen.
: If PB CAMERA TITLE is on, camera title is displayed in palyback.
5
4
3
A
B
C
D
E
E
A C
B D
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
Display of DISPLAY SETUP
: If DVR STATUS is on, operation status of DVMR like REC/PLAY is displayed.

1. Start of SETUP
1) Press [MENU] button.
2) Log into the system by entering password.
3) Select SEPUP item using button
4) Press [ENTER] button to enter submenu of selected SETUP item.
5) Select SEPUP item in submenu using button, and change value using button
6) Press [ENTER] button to select SEPUP item, and press [MENU] button to go back to
previous menu.
14
SYSTEM SETUP
SELECT UP/DOWN , ENTER
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
7) If you choose FACTORY DEFAULT, all settings shall be changed to settings done by manufacturer,
and we recommend you to set at FACTORY DEFAULT in the first operation, or when
you replaced EPROM for upgrading DVMR program or replaced HDD.
You can set all group of settings at FACTORY DEFAULT as a whole or group by group.
If you want it as a whole, set ALL SET at ON by pressing [ENTER] button, and set ALL SET at OFF
and set each group of FACTORY DEFAULT at ON or OFF independently by pressing [ENTER] button.
After you decide ALL SET or group by group set, move to RESET NOW and press [ENTER].
SETUP items remain unchanged even though you choose FACTORY DEFAULT
1. Time and date of TIME/DATE SETUP 2. All recorded data on HDD
3. Marked data 4. ADMIN password
5. ALARM LIST SETUP
NOTICE : In the first operation of this DVMR, we recommend users to set at FACTORY DEFAULT before you select various parameters of
operation.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
5-4. SETUP
Display of SYSTEM SETUP
2. DISPLAY SETUP
: If TIME and DATE is on, time and date of recorded pictures is displayed in playback.
DISPLAY SETUP
TIME/DATE
CAMERA TITLE
PB TIME/DATE
PB CAMERA TITLE
DVR STATUS
SELECT , PRESS
: ON
: ON
: ON
: ON
: ON
1
2
3
4
5
This is about the contents displayed on the display screen.
2002/ARP12 AM 07:40:38
60FPS REC
CAM1
15
1
2
: If TIME/DATE in on, time and date is indicated on live screen.
: If CAMERA TITLE is on, camera title is displayed on live screen.
: If PB CAMERA TITLE is on, camera title is displayed in palyback.
5
4
3
A
B
C
D
E
E
A C
B D
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channelstand-aloneDVR5. Operation
Display of DISPLAY SETUP
:IfDVRSTATUSison, operation status of DVRlike REC/PLAYisdisplayed.

5. MARK IMAGE SETUP
4. Playback speed setup
1) During playback, press [speed] button.
2) Screen on the right will appear.
3) Set direction of playback using key.
4) Set speed of playback using key.
(High speed up to x60 and slow speed up to
1 field/60 sec are available)
You can store some pictures very specially if you press [MARK] button during palyback. Pictures between you
first press [MARK] button and you press [MARK] button again shall be protected from being overwritten when
HDD is full. And it is very useful feature to utilize some important pictures to be safe from being deleted by mistake.
13
Press
1X PLAY SPEED
2X PLAY SPEED
4X PLAY SPEED
8X PLAY SPEED
16X PLAY SPEED
32X PLAY SPEED
60X PLAY SPEED
Press
1X PLAY SPEED
1/2 PLAYSPEED
1/4 PLAYSPEED
1/8 PLAYSPEED
1/16 PLAYSPEED
1/32 PLAYSPEED
1/60 PLAYSPEED
2002/APR/12 AM 07:40:38
1X PLAY SPD
CAM1
Indicate playback speed
Represent [SPEED]
button is pressed
MARK IMAGE SETUP
SELECT , PRESS ENTER
TOTAL FRAME 0
START TIME
/ / : :
EMD TIME
/ / : :
PLAY MARK IMAGE
DELETE MARK IMAGE
SYSTEM SETUP
DISPLAY SETUP
CAMERA TITLE
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
BUZZER SETUP
ID/PW SETUP
SCHEDULE REC SETUP
PANTILT CMD SETUP
HDD INFORMATION
MARK IMAGE SETUP
PRODUCT ID
Refer to MARK IMAGE SETUP in MISCELLANEOUS SETUP in 5-4)- - in page 28
86
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
Play just marked
pictures or delete
marked pictures
Display of MARK IMAGE SETUP
3. CAMERA SETUP
1
2
TITLE SETUP : Input title of camera.
COLOR BAR TEST : Displays COLOR BAR CHART.
Press [ENTER] button then move to any location you
want using button, and then select letters using
button.
After complete to change, press [MENU] button to
return to main menu.
16
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
CAMERA TITLE SETUP
SELECT , PRESS ENTER
0 1 2 3 4 5 6 7 8 9 . , < > ( ) - = A B C D
E F G H I J K L M N O P Q R S T U V W X Y Z a b
c d e f g h I j k l m n o p q r s t u v w x y z
> CH1 < CAM 1 >
Display of CAMERA TITLE SETUP
Use to adjust colors of monitor.

2) After [PAUSE] button, press button to advance picture by picture in both direction. It is useful
to check one after the other carefully.
1. How to replay
1) Press [PLAY] button to begin playback.
2) Screen on the right will appear.
3) Press [PLAY] button to start playback
from the first of recorded data.
2. GOTO time settings
1) Select G(GOTO) submenu and move cursor using key to set.
2) Using key, set year, month, date, time at which you want to to start.
(To start from a specific time, first set the
GO TO time before press [PLAY] button)
3) Press [PLAY] button to start playback.
NOTICE : During playback or settings in SETUP menu, recording is stopped.
3. Pausing and advancing picture by picture
1) During playback, press [PAUSE] button to pause. Press once more to play again.
12
NOTICE : When value out of range of start and end of data entered, it starts from START time.
S : 2002/APR/07 AM 07:40:38
E : 2002/APR/07 PM 02:11:56
G : 2002/APR/07 AM 00:00:00
2002 / APR / 01 AM 04:34:54
STOP
Indicates
recording is
stopped
: Cursor
S (START) : Start of recording
E (END) : End of recording
G (GOTO) : Set time from which
playback starts
NOTICE : When value is in the range of START and END, but there is no recorded picture at the set time, it moves to the closest time
of the recorded picture.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
5-3. Play
Display of Playback
4. TIME/DATE SETUP
2SET TIME/DATE TYPE : Sets notation of TIME/DATE
1. HOUR DISPLAY : Choose AM/PM type or 24 hours time indication
2. DATE DISPLAY : Select Asian type, American type, or European type.
3. MONTH DISPLAY : Choose indication of MONTH in Alphabet or Number
17
SET TIME/DATE
YEAR
MONTH
DAY
HOUR
MINUTE
SECOND
SELECT , PRESS
2002/APR/15
PM 09:23:17
Display of SET TIME/DATE
1SET TIME/DATE : Sets year/month/day/hour/minute/second
With button, move to year/month/day/hour/monute/second, and change value
using button.
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
SET TIME/DATE
SET TIME/DATE TYPE
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
SET TIME/DATE
SET TIME/DATE TYPE
TIME/DATE TYPE SETUP
HOUR DISPLAY
DATE DISPLAY
MONTH DISPLAY
SELECT , PRESS
: AM/PM
: ASIAN
: ENGLISH
Display of TIME/DATE TYPE SETUP
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1channel stand-alone DVR 5. Operation

11
3. Sensor recording
Refer to REC MODE SETUP in 5 -4 - 5 - (RECORD SETUP) in page 21 for more detail of TIME+ALARM OR
MOTION+ALARM and ALARM SETUP 5- 4- 5 - in page18(alarm setup) for more detail of ALARM
DURATION.
5. Recording by MOTION DETECTION
Refer to ALARM/MOTION SETUP in 5- 4- 5 from page 18
to 20. It must be set at MOTION or MOT+ALM to record
whenever motion is detected.
1) When there is sensor input, recording starts. 2) It records for preset period of time.
For more details, refer to SCHEDULE REC SETUP in MISCELLANEOUS SETUP in 5- 4- 8 - in page 24
4. Scheduled recording
3
1
3
6. Attention
1) Recording is stopped during SYSTEM SETUP.
2) Recording is stopped during playback or when in SEPUP
menu.
3) Recording is not possible if no camera is connected.
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channel stand-alone DVMR 5. Operation
RECORD SETUP
HDD CLEAR
HDD FULL
RECORD MODE
RECORD SPEED
MUX CH NUMS
SELECT , PRESS
: NO
: OVERWRITE
: MOT+ARM
: 60FPS
: 16CH
MOT+ALARM : Records when motion detected or when alarm is activated for preset duration time in above example.
>Or set at
TIM+ARM
ALARM SETUP
ALARM SIGNAL
> ALARM DURATION
SELECT , PRESS
: N.C
: 20 SEC
Set duration of
alarm
1
2
Records as scheduled, and setting can be done by date or by day of the week.
For each day, 2 different time intervals can be set at ON or OFF in the unit of 30 minutes, and same for each
day of the week. Therefore users can set 4 recording time intervals of recording or not recording for every day.
RECORD SETUP
HDD CLEAR
HDD FULL
RECORD MODE
RECORD SPEED
MUX CH NUMS
SELECT , PRESS
: NO
: OVERWRITE
: MOTION
: 60FPS
: 16CH
>or
MOT+ARM
Display of RECORD MODE
5. ALARM/MOTION SETUP
1
ALARMSETUP:Setstype of sensors connected toDVRunit.
OFF : Not in use.
NC : Normal closed. When an event happens, contact is opened.
NO : Normal open. When an event happens, contact is closed.
ALARM DURATION : Duration of recording when an ALARM is activated.
18
2
ALARM SETUP
> ALARM SIGNAL
ALARM DURATION
ELECT LIST TYPE
SELECT , PRESS
: N.C
: 20 SEC
: ALM
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
ALARM LIST SETUP
SELECT , ENTER , MARK
DATE
> --/--/--
--/--/--
--/--/--
--/--/--
--/--/--
TIME
--/--/--
--/--/--
--/--/--
--/--/--
--/--/--
ALM
--/--/--
--/--/--
--/--/--
--/--/--
--/--/--
SORT DELETE GOTO
SYSTEM SETUP
DISPLAY SETUP
CAMERA SETUP
TIME/DATE SETUP
ALARM/MOTION SETUP
RECORD SETUP
TCP/IP SETUP
MISCELLANEOUS
FACTORY DEFAULT
ALARM SETUP
ALARM LIST SETUP
MOTION SETUP
MOTION MASK SETUP
A: ALARM
L : LOSS
M : MOTION
Playback from GOTO
time
(set time : 10, 20, 30, 40, 50 sec, 1 MIN, 3 MIN, 5 MIN)
ALL ABOUT IMAGE RECOGNITION & PROCESSING
1 channelstand-aloneDVR 5. Operation
Using button, move to any of SORT/DELETE/GOTO
Display of ALARM LIST SETUP
Display of ALARM SETUP
ALARM LIST SETUP : Shows list of alarms up to 400. If total alarm exceeds 400, it overwrites from
the beginning. Alarmlist isveryuseful tomanage DVRsystem,in case itisin use in connection
with alarm sensors.
SELECT LIST TYPE : “A” indicates Alarm, “L” indicates Loss, and “M” indicates Motion.
You can select group of events, NONE, A, L, and M, by pressing [left] and
[RIGHT] buttons. If you select NONE, no event list shall be provided.