Acme Packet Net-Net 2620 User manual

Installation references
System Installation and Commissioning Guide
Net-Net® 2620 Network Interface Card (NIC) Installation
What’s inside the box?
• Network interface card (P/N HW-NIC-2TX,
HW-NIC-2TE, or HW-NIC-2SX)
Tools required:
• Phillips #1 and #2 screwdriver.
• Attach an antistatic wrist strap when handling
all components in this installation.
3Remove the riser assembly.
1. Disconnect any cables attached to any of the
installed network cards.
2. Lift up on the two levers on the riser to lift
the assembly from the chassis.
4
Clip
Clip
Network interface card
Install the NIC card(s) into the riser assembly.
1. Open the blue retention clips, both of them, as shown.
2 Insert the card, pressing it in until it seats
in the riser full-height card connector slot number 2. Make sure
the bracket inserts into the matching slot.
3. Look at the Ethernet connectors on the interface side to ensure
that the card is properly oriented, and not crooked.
4. Close the blue retention clips.
5. Repeat this step to install additional NICs in riser slots 4, 3,
5 and 6, in this order. Slot 1 is not present in the Net-Net 2620.
Note: The 2TX and 2SX cards fit in the full-height slots only.
2
4
6
Connect cables and re-install the riser assembly.
1. Set the riser assembly straight down, matching the
hooks in the back of the riser assembly to the notches
at the rear of the chassis.
2. Press firmly to push the insert into the slot on the
server board.
3. Connect the cables to the NIC.
5
2Remove the air duct.
1. Lift the processor air duct from its location
over the processor sockets.
2. Put the air duct aside for reinstallation later.
®
Remove the Net-Net 2620 top cover.
1. Unplug the chassis and remove it
from the rack.
2. Disconnect the power cord.
3. Remove the shipping screw (A)
4. Holding the blue button (B), slide the
top cover back.
5. Lift the top cover upward and remove it.
A finger notch is provided for lifting.
1
Use these instructions for installing standard network
interface cards in Net-Net 2620 systems without the
presence of any media expansion cards.

Re-install the air duct.
1. Place the air duct over the processor sockets.
The front edge of the air duct should contact the fan
module and the top of the installed air duct should be
flush with the top surface of the power supply.
2. Use caution not to pinch or disengage cables that may
be near or under the air duct.
6Replace the Net-Net 2620 top cover.
1. Place the cover over the chassis so that the side
edges of the cover sit just inside the chassis
sidewalls.
2. Slide the cover forward until it clicks into place.
3. Insert the shipping screw (B) at the center of the
top cover using the Phillips screwdriver.
4. Re-install the power cord and return the system
to its rack location.
5. Reconnect network cables.
7Note the slot numbering at the back of the system.
See the Post Installation notes below.
Net-Net 2620
full-height slots
Net-Net 2620
half-height slots
12
34
56
Note: Slot 1 is not present in the Net-Net 2620.
8
Net-Net®Network Interface Card (NIC) Installation (cont.)
Post installation notes:
1. The Ethernet port numbering depends on the number of NICs that are installed. Port
numbering runs left to right and progresses from top to bottom when viewing the back
of the system.
2. NICs maintain their port numbering and MAC addressing after initial NN2600
software installation.
3. When relocating a NIC from a half-height slot to a full-height slot, the orientation of the
card will be reversed in the new full-height slot installation. This means that the port
numbering from the original installation will be reversed in the new slot.
4. Adding new NICs after the initial installation will result in new port numbers that begin
using the highest port number plus 1. For example, if the highest port number is eth11, the
first port number on the newly added card, regardless of the slot, will be eth12.
Net-Net OS-E
Net-Net 26260 Network Interface Card (NIC)
Installation
2010 Acme Packet, Inc.
All rights reserved.
Acme Packet
100 Crosby Drive
Bedford, MA 01730 USA
t 781-328-4400
f 781-275-8800
http://www.acmepacket.com
Last Updated: December
2010
Proprietary & Confidential