AcSiP AI50H EVK User manual
AcSiP Technology Corp. www.acsip.com.tw
AI50H EVK Connector Description
USB 轉BASIC UART
FT230XQ,FTDI
Components Not
Populated Area
Mini-USB
Connecter
5V & 3.3V power supply LED
=0Ω Resister
X10pcs
AcSiP Technology Corp. www.acsip.com.tw
AI50H EVK Connector Description
PA8
PA8PA8
PA8
PA9
PA9PA9
PA9
PB10
PB10PB10
PB10
PB11
PB11PB11
PB11
GND
GNDGND
GND
VDD
VDDVDD
VDD
BOOT0
BOOT0BOOT0
BOOT0
NRST
NRSTNRST
NRST
VDD
VDDVDD
VDD
VDD
VDDVDD
VDD
VDD
VDDVDD
VDD
VDD
VDDVDD
VDD
GND
GNDGND
GND
PB15
PB15PB15
PB15
PA15
PA15PA15
PA15
PC13
PC13PC13
PC13
PB3
PB3PB3
PB3
PB4
PB4PB4
PB4
PB5
PB5PB5
PB5
GND
GNDGND
GND
PB6
PB6
PB6
PB6
PB7
PB7
PB7
PB7
PB8
PB8
PB8
PB8
PB9
PB9
PB9
PB9
PC0
PC0
PC0
PC0
PC1
PC1
PC1
PC1
PC2
PC2
PC2
PC2
PC3
PC3
PC3
PC3
PC4
PC4
PC4
PC4
PC5
PC5
PC5
PC5
PC6
PC6
PC6
PC6
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
PA4
PA4
PA4
PA4
PA5
PA5
PA5
PA5
PA6
PA6
PA6
PA6
PA7
PA7
PA7
PA7
GND
GND
GND
GND
PA12
PA12
PA12
PA12
PA11
PA11
PA11
PA11
PA10
PA10
PA10
PA10
PB14
PB14
PB14
PB14
PB13
PB13
PB13
PB13
PB12
PB12
PB12
PB12
PB2
PB2
PB2
PB2
PB1
PB1
PB1
PB1
GND
GND
GND
GND
GND
GNDGND
GND
PA13_SWD
PA13_SWDPA13_SWD
PA13_SWD
PA14_SCK
PA14_SCKPA14_SCK
PA14_SCK
VBAT
VBATVBAT
VBAT
VREF+
VREF+VREF+
VREF+
VDDA
VDDAVDDA
VDDA
VDD
VDDVDD
VDD
GND
GNDGND
GND
AcSiP Technology Corp. www.acsip.com.tw
AI50H EVK Schematic Diagram
Module peripheral Circuit Diagram
Components Not Populated Area
AcSiP Technology Corp. www.acsip.com.tw
AI50H EVK Schematic Diagram
USB to UART Circuit Diagram
AcSiP Technology Corp. www.acsip.com.tw
AI50H EVK Schematic Diagram
Power Supply Circuit Diagram
AcSiP Technology Corp. www.acsip.com.tw
Antenna Specifications
AcSiP Technology Corp. www.acsip.com.tw
Antenna Specifications
N-female to IPEX-1 Cable
AcSiP Technology Corp. www.acsip.com.tw
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC ules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
- eorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC ules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
AcSiP Technology Corp. www.acsip.com.tw
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter. Country Code selection feature to be disabled for products marketed to the US/CANA.
Integration instructions for host product manufacturers
Applicable FCC rules to module
FCC Part 15.247
Summarize the specific operational use conditions
The module is must be installed in mobile device.
This device is intended only for OEM integrators under the following conditions:
1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
2. The transmitter module may not be co-located with any other transmitter or antenna
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed.
AcSiP Technology Corp. www.acsip.com.tw
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co-location with another transmitter), then the FCC authorization is no longer considered valid and the
FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization. The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which integrates this
module. The end user manual shall include all required regulatory information/warning as show in this
manual.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
20 cm separation distance and co-located issue shall be met as mentioned in “Summarize the specific
operational use conditions”. Product manufacturer shall provide below text in end-product manual
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.”
AcSiP Technology Corp. www.acsip.com.tw
Antennas
Brand name Model name Antenna type Antenna gain Antenna connector
Aristotle RFA-WAVE-C55-U-B70-1 Dipole 2 dBi R-SMA
lian han tech corp. OMA-G01 Dipole 8 dBI N type
Label and Compliance Information
Product manufacturers need to provide a physical or e-label stating
Contains FCC ID: 2ADWC-AI50H” with finished product
Information on Test Modes and Additional Testing Requirements
Test tool: termite-3.3 shall be used to set the module to transmit continuously.
Additional Testing, Part 15 Subpart B Disclaimer
The module is only FCC authorized for the specific rule parts listed on the grant, and that the host
product manufacturer is responsible for compliance to any other FCC rules that apply to the host
not covered by the modular transmitter grant of certification. The final host product still requires
Part 15 Subpart B compliance testing with the modular transmitter installed
AcSiP Technology Corp. www.acsip.com.tw
Professional installation instruction
Please be advised that due to the unique function supplied by this product, the device is intended for use with our
interactive entertainment software and licensed third-party only. The product will be distributed through controlled
distribution channel and installed by trained professional and will not be sold directly to the general public through
retail store.
1. Installation personal
This product is designed for specific application and needs to be installed by a qualified personal who has RF and
related rule knowledge. The general user shall not attempt to install or change the setting.
2. Installation location
The product shall be installed at a location where the radiating antenna can be kept 20cm from nearby person in
normal operation condition to meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The non-approved antenna(s) may produce
unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC/IC limit and is
prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the final output power does not exceed the limit
set force in relevant rules. The violation of the rule could lead to serious federal penalty.
Table of contents
Other AcSiP GSM/GPRS Module manuals
