Acson AAD13A User manual

1
OPERATION MANUAL
AROMA DIFFUSER
AAD13A

2
CONTENTS
1.0
Introduction
4
2.0
Product Overview
5
3.0
How to Use
6
4.0
Safety Instructions
9
5.0
Maintenance
13
6.0
Troubleshooting
14
DISCLAIMER
In complying with the policy for continuous improvement of Acson
Malaysia Sales & Service Sdn Bhd (herein after referred to as “Acson”),
the information contained in this document is subjected to change
without prior notice. While Acson makes no commitment to update or
provide current information automatically to the manual owner, that
information (if applicable) can be obtained by contacting the nearest
Acson office, distributors or dealers network. It is the responsibility of
the operator or service personnel to verify the applicability of these
documents, then prior to working on the equipment. They should verify
with the owner whether the equipment has been modified and if current
literature is available.

3
CAUTION
Please do not pour water directly on the mist outlet or it will damage
the product.

4
INTRODUCTION
Aroma diffuser or essential oil diffuser adopts the principle of ultrasonic
atomization. During the processof dispersing the essential oil, theroom
is filled with the fragrance. It could act as a humidifier to retain the
moisture in the air if no essential oil is added.
Product
Aroma Diffuser
Model Name
AAD13A
Volume
130 ml
Rated Voltage
5V
Rated Power
5W
Unit Dimension
(HxWxD)
160 x 106 x
106 mm
Net Weight
0.24 kg
Material
ABS+PP

5
PRODUCT OVERVIEW
Mist Outlet
Cover
Mist Outlet
USB Port
Splashboard
Air Outlet
Water Level
Sensor
On/ Off
Button
Air Inlet/ Water
Drain Hole

6
HOW TO USE
1. Open the cover.
2. Add moderate amount of water and essential oil.
The water level should not beyond the maximum water level
indication.
Add few drops of essential oil into water.
Volume of
Water Added
Suggested Amount
of Essential Oil
Duration
50 ml
1-2 drops
30 min –1 hour
100 ml
2-4 drops
1 –2 hours
130 ml
4-6 drops
2 –3 hours

7
Note: Please do not remove the water level indicator when adding the
water to prevent water level from exceeding maximum level indication.
3. Connect to power supply.
Connect the USB cable to any USB power source.
When the power supply is connected, Standby Mode is activated.
The unit will flash yellow light for once.
Maximum Water Level
Water Level Sensor

8
4. Activate the mist function.
Press the mist button for once, it will activate Continuous Mode.
Unit will keep misting until user turn off the unit.
Press it again, the unit will then switch to Interval Mode. Unit will
mist for 10 seconds, pause for 10 seconds, then mist again.
Press it again, the unit will return to Standby Mode.
5. Activate the ambient light.
Press the light button, warm light is turned on.
Press it again, Rainbow Mode is activated by switching between
7 colours ambient lighting.
Press it again, the colour of light is fixed at the selected colour.
Press it again to turn off light function.
Mist button
Light button

9
SAFETY INSTRUCTIONS
1. The unit must be powered with correct power supply.
2. It is prohibited to fill water directly into the mist outlet.
3. The misting effect is slightly different between each units after they
are manufactured. Various factors are identified to be effecting the
misting effect, such as types of water, surrounding temperature,
humidity and direction of wind.
4. If the water is lower than certain predefined level, the unit will flash
red light for 5 times to indicate water shortage. In case of water
shortage, misting function could not be used, where light function
could be used as usual.
5. Corrosive liquids are prohibited to be in touch with the unit, or else
it will damage the unit.
6. In the event of replacement of essential oils, please follow the safety
instructions and cleaning tips to clean the unit.
Note: When the water is running out, the misting will be stopped. Unit will
flash red light for 5 times to indicate water shortage. Then it will
automatically switch to Standby Mode.

10
SAFETY INSTRUCTIONS
In case of unit tilting or water pouring out, please proceed with the
following safety instructions:
1. Shut down the unit and pull the power cord out of unit.
2. Pour out the remaining water. Do not pour out from the air outlet (as
shown in the following picture) to prevent water entering the circuit
board.
3. Lean the unit and drain the remaining water from the air inlet.
4. Leave the unit in a cool dry place for 24 hours to let it dry completely.
Air Inlet/ Water
Drain Hole
On/ Off Switch

11
WARNING
Please take note on the following precaution steps to safely operate
this unit.
1. This kind of product is limited to the scope specified in the product
specification as shown in product catalogue and User Manual.
2. Do not open the cover or refill water and essential oil while misting.
Please turn off the power supply before you do so.
3. Avoid oral ingestion and internal application of essential oil.
4. This product is not a toy. Keep out of reach of children. Patient and
elderly person should operate this unit under supervision.
5. It is prohibited to rebuild or dismantle this product. If necessary to
do so, please contact our sales personnel, then we will send our
professionally trained technicians to rework or repair the product.
6. Please do not intentionally stab, twist or stretch the power cord.
Please do not place the power cord near to heat source or under
high temperature. Do not put additional weight on the power cord or
it might cause damage.
7. The power cord of this product very sensitive. If something wrong
with the power cord, please stop operating the unit immediately, and
contact our sales personnel to handle it.
8. Please do not location this product in the places with high humidity
such as bathroom and greenhouse etc.
9. To ensure 100% hygiene, please pour out all the water in the water
tank after operating it. Please clean the water tank and dry the
surface of the unit with clean dry cloth.

12
10.Aromatherapy essential oil may result in stain on water tank. If such
case happened, wipe the unit with clean dry cloth immediately.
11.Please do not directly mist on furniture, clothes or walls.
12.Please avoid operating the unit under direct sunlight exposure, and
avoid operating the unit nearby electrical appliances such as
television, sound system, air conditioner and ventilator. Avoid use
in high temperature area. Do not put it near to stove or other source
of heat.
13.Please locate the unit on flat surface only. Please do not put in on
slanted surface or water might spill out.
14.When the unit is operating, do not move the unit.

13
MAINTENANCE
Please clean the unit regularly after operating it for 5 to 6 times or 3 to
5 days depending on the frequency of usage.
1. Power off and unplug the power cord.
2. Pull out the cover.
3. Pour out all the water in water tank and clean it.
4. Use a cotton swab to clean the surface of ultrasonic atomizer with
dilute detergent and water.
5. Pull out the splashboard, then use a cotton swab to clean the
surface of splashboard and the hole with diluted detergent and
water.
6.
7. Use a soft cloth to clean the entire surface of the unit. Do not use
phenethyl alcohol or any other strong chemicals or it will cause the
unit surface to be decolourised.
8. Please unplug the power source, pour out all the water, clean the
unit and store in a cool dry place if the unit is not used for a long
period.

14
TROUBLESHOOTING
If the unit could not perform regularly, please check the following
troubleshooting guidelines.
Problem
Reason
Solution
Unit not
function
USD cable and
power supply do
not connect
correctly.
Make sure USB cable is
connected with power
supply. To verify it, please
pull out the cable and plug
in again.
Power
supply is
connected
but unit do
not mist
Water level
lower than
minimum water
level.
Refill the water following
recommendation.
Water level
higher than
maximum water
level.
Pour out some water. The
water level should not
exceed maximum water
level indication (130ml).
Dirt/ stain on
ultrasonic
atomizer.
Use a cotton swab to clean
the surface of ultrasonic
atomizer with dilute
detergent and water.
Dusty air inlet.
Use a cotton swab to clean
the air inlet. Dust on air
inlet will reduce the
efficiency of the unit.

15
目录
1.0
产品介绍
17
2.0
产品概述
18
3.0
使用方法
19
4.0
安全指南
22
5.0
保养说明
26
6.0
故障排除
27
声明
在遵守 Acson Malaysia Sales & Service Sdn Bhd（此后称为 Acson）
持续改进政策的情况下，本文档中包含的信息如有更改，恕不另行通
知。虽然 Acson 不承诺自动更新或向手册拥有者提供当前信息，但可
联系临近的 Acson 办事处、经销商或经销商网络，获取该信息（若适
用）。在操作设备之前，操作员或服务人员有责任验证这些文件的适用
性。他们应该与持有者核实设备是否已经过修改，以及是否拥有最新文
档。

16
警告
请勿往出雾口倒水，否则可能会损坏机器。

17
产品介绍
芳香扩散器或精油扩散器采用超声雾化原理。在分散精油的过程中，房
间充满了香味。如果不添加精油，它可以作为加湿器，保持空气中的水
分。
产品名称
超声波香薰机
产品型号
AAD13A
水箱容量
130 ml
额定电压
5V
额定功率
5W
产品尺寸
(高x长x宽)
160 x 106 x 106 mm
产品净重
0.24 kg
材质
ABS+PP

18
产品概述
出雾口
上盖
喷雾口
USB 电源接口
挡水板
出风口
测水凸点
开关按钮
进风口/ 排水口

19
使用方法
1. 向上提起上盖。
2. 加入常温的水和精油。
往水箱内加入适量的水，水量要超过测水凸点，但是不能超过挡
水板上大的最高水位标识。水箱注水后，垂直滴入香薰精油。
装水量
建议精油量
持续时间
50 ml
1-2 滴
30 分钟 –1 小时
100 ml
2-4 滴
1 –2 小时
130 ml
4-6 滴
2 –3 小时

20
注意： 加水时，请勿拔出挡水板，以免水量超过最高水位标识。
3. 连接电源。
请将电源线的 Micro插头连接主机 DC插座，然后将电源线的 USB
插头连接到正确的供电体上（注：本机输入的电压为 5V，电流≥
1A）。
当电源接通后，机器黄灯闪烁一次，提示电源接通，进入待机模
式。
最高水位线
测水凸点