ACT ACTPRO IOM User manual

ACTpro IOM Input / Output Module
Product Overview
This is an 8 Input and 8 Output device that allows
an ACT controller to be used in applications where
signalling to other equipment is required. Examples
of this are elevator control, alarm systems, CCTV
switching applications, I/O Mapping etc.
Main Features
8 form C 5 Amp relays
8 supervised inputs
Tamper protection
2 status LEDs
Polycarbonate housing
Input and output names
Timer for each output
Output switched off or on by log
event, input, timezone
ACTWin pro support
Inputs and outputs Logged
Normally open/closed
Inputs monitored by timezone
Supervised Inputs option
Installation / Specification Guidelines
Up to 4 ACTpro IOMs may be connected
to each ACT controller bus, giving control
of up to 32 inputs and 32 outputs for each
controller
The controllers may be networked via RS485
or TCP/IP to control up to 1000 inputs and
1000 outputs maximum
The device may be installed indoors only
and requires +12V DC
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
ACTpro IOM module requires a 12 volts DC supply
ACTpro IOM System Schematic
ACTpro IOM
LAN / Ethernet
Database
Server
IOM
8
8
3000
100
IOM
8
8
2000
100
IOM
8
8
3000
100
200 200200

ACTpro IOM Input / Output Module
Product Specification
Operating Voltage: 12 Volts DC
Current Consumption: 300 mA
Weight: 375 grams
Operating Temperature: -10 to +50 C
Dimensions (HxWxD): 110 x 190 x 60 mm
Mounting: Surface
Installation: Indoor
Cabling Chart
From To Cable Restriction
Ordering Information
ACTpro IOM
Reader
ACTpro
100/200
Controller
Controller
Network
RS485
interface
Controller
Controller
Controller
PC Direct
RS232
Network
RS485
interface
PC
Twisted
screen
pair
or Cat 5
8 core
screen
Twisted
screen
pair
or Cat 5
Twisted
screen
pair
or Cat 5
Twisted
screen
pair
or Cat 5
Cable
Supplied
Maximum
1.4km
30m at 5volts
100m at
12volts
Maximum
1.4km
Maximum
30m
Maximum
1.4km
Maximum
30m
Access Control Technology Unit C1, South City Business Park, Tallaght, Dublin 24, Ireland.
t: 353 (0) 1 466 2570. f: 353 (0) 1 452 0427. e: [email protected]. w: www.accesscontrol.ie
I/O Module
Controller
ACTpro IOM
ACTpro 3000/2000
ACTpro IOM Applications
Elevator control
In this application, a user presents a card to the proximity reader when they
enter the cab. This enables the buttons for the floors to which the user has
access. The buttons stay on for a programmable amount of time (normally
7 seconds) and then switch off. When the user selects the floor, the buttons
turn off.
Alarm Systems
The unit can be programmed to activate a relay on alarm events such as
tamper, door forced, mains fail etc. It can also monitor the status of certain
inputs and switch an output when the input changes state. All changes are
fully logged in ACTWin pro complete with timestamp.
Building Management
The ACTpro IOM allows ACT controllers to be used in building management
applications. It can switch an output to turn on heating or lighting at certain
times or only when someone is present. It can also switch off heating when
the last person has left the room, saving on energy costs.
CCTV systems
Using an ACTpro IOM allows switching of CCTV cameras when someone
enters a room or when access is denied. When used in combination with
the Challenge feature of ACTWin pro, the image on the camera may be
compared against a pre-stored photo.
ACTpro IOM
ACTpro 3000/2000 ACTpro 100
Door Expander
ACTpro 200
2 Door Expander