Action Sports Super Play Fort II User manual

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 1
Action Sports Equipment Pty Ltd.
72 Silverwater Rd, Silverwater, NSW, Australia, 2128
Parts & Service Enquiries: 1800 465 070 (Australia); 09 477 6020 (New Zealand)
Or email: [e-mail] (Australia); [e-mail] (New Zealand)
Sales Enquiries: 1800 777 137 (Australia); 09 477 6020 (New Zealand)
Or visit our website: www.actionsports.com.au
Model: S001049 - Super Play Fort II
Assembly, Installation, Care, Maintenance and Use Instructions
Manual depicts typical installation
STANDARD UNIT SET UP
Plus Bonus sling swing pieces. These can
be substituted for the trapeze or tot
swing on the swing unit:
IMPORTANT
Please read and RETAIN this manual as it will assist with identification for parts and service.
Read this manual prior to assembling and using this Play Fort.
This Product is for Domestic Use Only.
- Warning -
- This play fort is for family domestic use only.
- This play fort is designed for use by children 3-9 years of age weighing no more than 34kgs.
- Tot Swing component only is designed for use by infants aged 19 months to 3 years.
- This play fort has a maximum total user weight limit of 204kgs (6 children).
- Children of all ages must be supervised by an adult at all times when using this play fort.
- Adult assembly of this play fort is required. Two adults are recommended for assembly.

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 2
- WARNING -
1) Read and understand enclosed safety information before assembly and use of the Play fort.
2) Place the play fort on a level surface before use.
3) Lateral clearance is essential. The play fort should be placed not less than 2m (6 feet 6 inches) from any structure or
obstruction ie. a fence, garage, house, shed, overhead branches, clothes line etc.
4) DO NOT install this play fort over hard surfaces such as concrete, asphalt or any other hard surface.
It is recommended that this play fort be positioned over soft lawn, sand or a soft ground material such as woodchips.
5) Anchor the play fort using the anchor pegs provided to prevent overturning or lifting. The anchors should be placed
level with or under the ground in order to reduce tripping hazards.
6) Never place the play fort under or near powerlines.
7) Never place the play fort inside a garage or basement or under any structure.
8) Always position the play fort where it can be seen from the house.
9) This play fort is designed to be used by one child per seat at one time.
10) Do not allow additional items to be attached to play fort set such as ropes, chains, cords, or other items not designed
for use.
11) Do not use the play fort when it is wet as it will become slippery and serious injury may result.
12) Do not wear apparel such as hats with chin straps, helmets, scarves, garments with pull strings and other items of loose
clothing while using this play fort as they can cause serious injury.
13) Do not walk close to, in front of or behind the swing set when in use, or in front of the slide base when in use. Walking
between moving rides can cause serious injury.
14) Do not jump from the swing set are while in motion.
15) Do not stand on the seats when using the swing set.
16) Do not climb on the side braces or the top support of the swing set, on the outside of roof of the play fort.

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 3
TABLE OF CONTENTS
PARTS LIST –MAIN FRAME ................................................................................................................................. 4
PARTS LIST –FORT.................................................................................................................................................4
PARTS LIST –SLING SWING................................................................................................................................. 5
PARTS LIST - TRAPEZE..........................................................................................................................................6
PARTS LIST –GLIDE RIDE ....................................................................................................................................7
PARTS LIST –TOT SWING.....................................................................................................................................7
PARTS LIST –SLIDE ............................................................................................................................................... 8
PARTS LIST –LADDER........................................................................................................................................... 9
PARTS LIST –FIREMAN POLE..............................................................................................................................9
PARTS MATCH LIST –1:1 Actual Scale................................................................................................................ 10
ASSEMBLYAND INSTALLATION INSTRUCTION........................................................................................... 17
SECTION 1 –FORT ASSEMBLY ..................................................................................................................18
SECTION 2 - MAIN FRAME ASSEMBLY.................................................................................................... 21
SECTION 4 - TRAPEZE ASSEMBLY............................................................................................................ 23
SECTION 5 –GLIDE RIDE ASSEMBLY...................................................................................................... 24
SECTION 6 –SLING SWING ASSEMBLY ..................................................................................................25
SECTION 7 –LADDER ASSEMBLY............................................................................................................26
SECTION 8 - SLIDE ASSEMBLY.................................................................................................................. 27
SECTION 9 –FIREMAN POLE ASSEMBLY ............................................................................................... 29
MAINTENANCE INSTRUCTION.........................................................................................................................30
CAUTION................................................................................................................................................................30
WARRANTY INFORMATION............................................................................................................................... 31

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 4
PARTS LIST –MAIN FRAME
Parts #
Parts
Description
Qty
A10
Top Support Tube with
pre-assembled Connector
(Rectangular Tube)
1
D17
Brace
1
A11
Left Leg Tube
1
A12
Right Leg Tube
1
X5
Anchor Peg
2
PARTS LIST –FORT
Parts #
Parts
Description
Qty
D60
Lower Main Frame Tube
4
D61
Sand Pit Stay
4
D62
Middle Main Frame Tube
4
D63
Fort Platform Support Tube
4
D64
Connect Tube to Swing or
Fireman Pole
2
D65
Connect Tube
2
D67
Canopy Roof Frame
2
D68
Upper Main Frame Tube
2
D69
Canopy Roof Support Tube
1

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 5
B23
Sand Pit Floor
1
B24
Sand Pit Cover
1
B25
Fort Jumping Mat
1
B32
Fort Enclosure Net
1
B27
Canopy
1
X20
Plastic Peg
4
PARTS LIST –SLING SWING
Parts #
Parts
Description
Qty
G1
Sling Swing Assembly
1
S3
EyeboltAssembly
(pre-assembled)
2
X6
Oval Opening Cap
(pre-assembled)
2

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 6
X16
Plastic Lock
(pre-assembled)
2
U1
Washer (M8)
(pre-assembled)
2
R8
Nylock Nut (M8)
(pre-assembled)
2
PARTS LIST - TRAPEZE
Parts #
Parts
Description
Qty
S3
Eyebolt & Link Assembly
(pre-assembled)
2
X6
Oval Opening Cap
(pre-assembled)
2
X16
Plastic Lock
(pre-assembled)
4
U1
Washer (M8)
(pre-assembled)
2
R8
Nylock Nut (M8)
(pre-assembled)
2
S2
Eyebolt
(Pre-assembled)
2
S5
Eyebolt Sleeve
(Pre-assembled)
2
X15
Ring Hook
(Pre-assembled)
2
U5
U-Shape Bracket
(Pre-assembled)
2
R6a
Hex Nut (M6)
(Pre-assembled)
2
R6b
Nylock Nut (M6)
(Pre-assembled)
2
B6
Trapeze Handle
2
G3
Chain
2
D32
Support Tube
1

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 7
PARTS LIST –GLIDE RIDE
Parts #
Parts
Description
Qty
D15
Glide Ride Hanger Tube
2
D16
Glide Ride Seat Tube
2
B4
Glide Ride Seat
2
B3
Glide Ride Foot Step
2
X3
Bracket
4
X4
Plastic Bearing
2
U3
T-Shaped Washer
4
PARTS LIST –TOT SWING
Parts #
Parts
Description
Qty
D18
Tot Swing
Hanger Tube
2
D19
Tot Swing Armrest Tube
1
D20
Tot Swing Support Tube
1
TS-5
Seat and Back Plate
(seat plate with one hole at the
centre of front panel)
2
S3
Eyebolt & Link Assembly
(pre-assembled)
2
U1
Washer (M8)
(pre-assembled)
2
R8
Nylock Nut (M8)
(pre-assembled)
2

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 8
PARTS LIST –SLIDE
Parts #
Parts
Description
Qty
MS-1
Metal Slide
1
MS-2
Slide Platform
1
MS-3
Slide Base Board
1
MS-4
Slide Support Tube
2
MS-6
Platform Support Tube
1
MS-16
Platform Base Tube
2
MS-17
Handle Tube
2
MS-18
Slide Leg Tube
2
MS-19
Stabilizing Tube
2
D51
Slide Leg Connecting Tube
1
D76
Fort Connect Tube
1

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 9
PARTS LIST –LADDER
Parts #
Parts
Description
Qty
D73
Ladder Tube
2
B31
Foot Step
3
X21
Plastic Cap
2
PARTS LIST –FIREMAN POLE
Parts #
Parts
Description
Qty
D77
Fireman Pole Tube with
pre-assembled Connector
1
D78
Base
1
X6
Peg
2
FP2
Long nut Washer Hex bolt
Long Nut Bolt
(1) Ø 6x40mm - long nut
(2) Ø 6.5mm - washer
(3) Ø 6x15mm –hex bolt
1

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 10
PARTS MATCH LIST –1:1 Actual Scale

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 11

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 12

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 13

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 14

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 15

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 16
Tools included in the Item
Wrench x 2 Allen Key
We recommend using a socket set (not included) which will make the installation easier and quicker.

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 17
- IMPORTANT -
Use this parts list to make sure all parts are present before assembly. Do not attempt to assemble the swing
set if any parts are missing or damaged. Inspect the slide before each use. Disassemble the Swing Set
immediately if any part is missing or any unsafe condition exists. Obtain a replacement part to properly
correct any issue by calling 1800 465 070 (Australia) or 09 477 6020 (New Zealand). Do not allow use of
the swing set until the issue has been corrected.
ASSEMBLYAND INSTALLATION INSTRUCTION
Read this entire assembly section before beginning to assemble your swing set. Carefully follow each step.
NOTE: At least 2 people are recommended for the following assembly.
In order to avoid injuries and damage to property, it is recommended
that the Play Fort should be at least 2 meters away from any buildings,
fences and other objects. Also clear the ground of any sharp objects.
Use the Parts List to make sure all parts are present. Contact Customer Service at 1800 465 070
(Australia) or 09 477 6020 (New Zealand) if any parts are missing. Do not attempt to assemble the swing
set if any parts are missing.

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 18
SECTION 1 –FORTASSEMBLY
Figure 1: Slide sand pit stays x 4 (D61) through each of
the side sleeves of the sand pit floor (B23). Place lower
main frame tubes x 4 (D60) on the four corners of the sand
pit floor, using one person to hold the poles vertically while
second person attaches components. Place ground support
pegs x 4 (X20) in corners, and attaches to lower main
frame tubes using (F3) bolt and nut x 4. Attach sand pit stays
(D61) in all four corners to lower main frame tubes (D60),
using (F2) bolt and nut x8. Double check fort is in correct
position and push ground support pegs firmly into the
ground.
Figure 2: Place sand pit cover over sand pit (B24).
Figure 3: Place Middle main frame tube D62 side by
side as shown in diagram.
Connect the four middle main frame tubes with
connection pieces D64 (x2) and D65 (x2) as shown. Add
upper main frame tube D68 (x2) as shown and connect
to middle main frame tubes. The two D68 pieces must
be on the same sides (parallel to) as the two D65 cross
pieces. Connect piece D64 on remaining side before
adding nuts and bolts.

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 19
Figure 4: With 2 people, lift middle section constructed in figure 3 and
connect as shown to base section. Do not add nuts or bolts at this point.
Figures 5 & 6: Slide the Fort
Enclosure Net (B32) over top of
frame as shown.
Figure 7: With one person holding the fort
jumping mat (B25), position mat so that support
loops on the mat overlap the loops at the base of
the fort enclosure net as per illustration. Add
Fort platform support tubes D63 (x4) to each
side, threading the support tube through the
loops of both the enclosure net and the jumping
mat as shown. On all four sides, add (F5) bolt
and nut x 8 for the upper holes on the middle
main frame tube D62.

©ACTION SPORTS EQUIPMENT PTY LTD –www.actionsports.com.au Page: 20
Figure 8: Connect Canopy roof frame D67 (x2)
to Canopy roof support tube D69 (x1) Using (F1)
bolt x2. Affix roof piece to main frame using
(F2) bolt and nut x8. Place canopy B27 over
roof frame.
Figure 9: Tension canopy at both ends over the roof
frame using the hook and loop strips at each end. Using
hook and loop pieces at the top of the Fort enclosure net
and in the corners secure and tension the fort sides.