Action Sports S000088NB Maintenance manual

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 1
Action Sports Equipment Pty Ltd.
72 Silverwater Rd, Silverwater, NSW, Australia, 2128
Parts & Service Enquiries: 1800 465 070 (Australia); 09 488 4750 (New Zealand)
Or email: [e-mail]
Sales Enquiries: 1800 777 137 (Australia); 09 488 4750 (New Zealand)
Or visit our website: www.actionsports.com.au
Action Multi Play Swings
Model: S000088NB
Assembly, Installation, Care, Maintenance and Use Instructions
IMPORTANT
Please read and retain this manual as it will assist with identification for parts and service.
Read these materials prior to assembling and using this swing set.
This Product is for Domestic Use Only.
- Warning -
- This swing set is for family domestic use only.
- This swing set is designed for use by children 3-9 years of age weighing no more than 34kgs.
- This swing set has a maximum weight limit of 200kgs.
- Children of all ages must be supervised by an adult at all times when using this swing set.
- Adult assembly of this swing set is required.

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 2
- WARNING -
1) Read and understand enclosed safety information before assembly and use of the swing set.
2) Place the swing set on a level surface before use.
3) Lateral clearance is essential. The swing set should be placed not less than 2m (6 feet 6 inches) from any
structure or obstruction ie. a fence, garage, house, shed, overhead branches, clothes line etc.
4) DO NOT install this swing over hard surfaces such as concrete, asphalt or any other hard surface.
5) It is recommended that this swing set be positioned over soft lawn or fine sand.
6) Anchor the swing set using the wiggling anchor pegs provided to prevent overturning or lifting. The anchors
should be placed level with or under the ground in order to reduce the tripping hazards.
7) Never place the swing set under or near powerlines.
8) Never place the swing set inside a garage or basement.
9) Always position the swing where it can be seen from the house.
10) This swing set is designed to be used by one child per seat at one time.
11) Do not allow additional items to be attached to the swing set such as ropes, chains, cords, or other items not
designed for use.
12) Do not use the swing set when it is wet as it will become slippery and serious injury may result.
13) Do not wear apparel such as hats with chin straps, helmets, scarves, garments with pull strings and other items
of loose clothing while using this swing set as they can cause serious injury.
14) Do not walk close to, in front of or behind the swing set when in use. Walking between moving rides can
cause serious injury.
15) Do not jump from the swing set when they are in motion.
16) Do not stand on the seats when using the swing set.
17) Do not climb on the side braces or the top support of the swing set.

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 3
TABLE OF CONTENTS
PARTS LIST – MAIN FRAME................................................................................. 4
PARTS LIST – SLING SWING................................................................................. 4
PARTS LIST - TRAPEZE ......................................................................................... 5
PARTS LIST – GLIDE RIDE .................................................................................... 6
PARTS LIST - SLIDE ............................................................................................... 7
SECTION 1- MAIN FRAME ASSEMBLY ..................................................... 10
SECTION 2- SLING SWING ASSEMBLY......................................................11
SECTION 3 - TRAPEZE ASSEMBLY ............................................................ 12
SECTION 4 – GLIDE RIDE ASSEMBLY....................................................... 13
SECTION 5 - SLIDE ASSEMBLY (I) ............................................................. 14
SECTION 6 - SLIDE ASSEMBLY (II) ............................................................ 15
SECTION 7 - SLIDE ASSEMBLY (III)........................................................... 15
SECTION 8 - SLIDE ASSEMBLY (IV) .......................................................... 16
MAINTENANCE INSTRUCTION......................................................................... 17
CAUTION .............................................................................................................. 17
LIMITED WARRANTY……………………………………………………………..18

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 4
PARTS LIST – MAIN FRAME
Parts # Parts Description Quantity
A10 Top Support Tube
(Rectangular Tube)
1
D17 Brace
(one with Center Hole for Slide)
(one without Center Hole)
2
A11 Left Leg Tube 2
A12 Right Leg Tube 2
X5 Anchor Peg 4
R55 Hex Bolt (M8*55mm) 4
R45 Hex Bolt (M8*45mm) 8
U1 Washer (M8) 4
R8 Nylock Nut (M8) 12
PARTS LIST – SLING SWING
Parts # Parts Description Quantity
S3 Eyebolt & Link
Assembly
2
X6 Oval Opening Cap 2
X16 Plastic Lock 2
U1 Washer (M8) 2
R8 Nylock Nut (M8) 2
G1 Sling Swing Assembly 1

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 5
PARTS LIST - TRAPEZE
Parts # Parts Description Quantity
S3 Eyebolt & Link
Assembly
2
X6 Oval Opening Cap 2
X16 Plastic Lock 4
U1 Washer (M8) 2
R8 Nylock Nut (M8) 2
S2 Eyebolt
(Pre-assembled)
2
S5 Eyebolt Sleeve
(Pre-assembled)
2
X15 Ring Hook
(Pre-assembled)
2
U5 U-Shape Bracket
(Pre-assembled)
2
R6a Hex Nut (M6)
(Pre-assembled)
2
R6b Nylock Nut (M6)
(Pre-assembled)
2
B6 Trapeze Handle 2
G3 Chain 2
D32 Support Tube 1

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 6
PARTS LIST – GLIDE RIDE
Parts # Parts Description Quantity
D15 Glide Ride Hanger
Tube
2
D16 Glide Ride Seat Tube 2
B4 Glide Ride Seat 2
B3 Glide Ride Foot Step 2
X3 Bracket 4
X4 Plastic Bearing 2
U3 T-Shaped Washer 4
R38 Hex Bolt (M6*38mm) 6
R50
Hex Bolt (M8*50mm) 2
R85 Hex Bolt (M8*85mm) 2
RN35 Round Head Bolt
(M6*35mm)
8
R6 Nylock Nut (M6) 14
R8 Nylock Nut (M8) 4
U2 Washer (M6) 4

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 7
PARTS LIST - SLIDE
Parts # Parts Description Quantity
R40 Hex Bolt (M6*40mm) 2
R32 Hex Bolt (M6*32mm) 1
R19 Hex Bolt (M6*19mm) 1
R14 Hex Bolt (M6*14mm) 2
RM35 Round Head Bolt w/
Square Inside
(M6*35mm)
2
RM32 Round Head Bolt w/
Square Inside
(M6*32mm)
4
RM41 Round Head Bolt w/
Square Inside
(M6*41mm)
2
R6 Nylock Nut (M6) 27
U2 Washer (M6) 15
D50 Step Tube 3
D51 On-Floor Step Tube 1
D52 Slide Leg Tube 2
D53 Swing Connector Tube 1
D54 Platform Support Tube 2
D55 Stabilizing Tube 2
D56 Slide Support Tube 2

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 8
D57 Platform Base Support
Tube
1
B20 Slide Plate 1
B21 Slide Platform 1
B22 Slide Base Board 1
R55 Hex Bolt (M6*55mm) 2
R35 Hex Bolt (M6*35mm) 9
R57 Hex Bolt (M6*57mm) 2
Tools included in the Item
Wrench Allen Key
- IMPORTANT -
Use this parts list to make sure all parts are present before assembly. Do not
attempt to assemble the swing set if any parts are missing or damaged. Inspect
the slide before each use. Disassemble the Swing Set immediately if any part is
missing or any unsafe condition exists. Obtain a replacement part to properly
correct the hazard by calling 1800 465 070 (Australia) or 09 488 4750 (New
Zealand). Do not allow use of the swing set until the hazard has been corrected.

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 9
ASSEMBLY AND INSTALLATION INSTRUCTION
Read this entire assembly section before beginning to assemble your swing set.
Carefully follow each step.
NOTE: At least 2 persons are recommended for the following assembly.
In order to avoid injuries and damage to
property, it is recommended that the
Swing Set should be at least 2 meters
away from any buildings, fences and so on.
Also clear the ground of any sharp objects.
Use the Parts List to make sure all parts are present. Contact Customer Service at 1800 465
070 (Australia) or 09 488 4750 (New Zealand) if any parts are missing. Do not attempt to
assemble the swing set if any parts are missing.

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 10
SECTION 1- MAIN FRAME ASSEMBLY
Assemble the Main Frame by using the provided tools Wrench and Allen Key as shown in
Figure 1.
Note: 1) At least two people are required to erect the Main Frame and Leg Tubes.
2) Make sure legs are positioned so that frame legs sit flush on ground, with peg hole
facing out and away from swing.
Figure 1
At the beginning, do not over tighten the screws when assembling the Legs (Part# A11 & A12)
to the Top Support Tube (Part# A10). This will make it easier to make final alignment and
adjustment. Once all screws have been properly aligned, tighten them securely.

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 11
SECTION 2- SLING SWING ASSEMBLY
Attach the Sling Swing to the Main Frame as shown Figure 3.
Figure 3
The correct installation of eye bolt requires that the thread of the bolt does not protrude
more than 1 to 2 complete turns/threads past the top of the Nylok nut.
WARNING!
DO NOT OVER TIGHTEN EYEBOLTS!
THIS CAN RESULT IN ASSEMBLY FAILURE!

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 12
SECTION 3 - TRAPEZE ASSEMBLY
Connect the Trapeze to the Main Frame as shown in Figure 4.
Figure 4
The correct installation of eye bolt requires that the thread of the bolt does not protrude
more than 1 to 2 complete turns/threads past the top of the Nylok nut.
WARNING!
DO NOT OVER TIGHTEN EYEBOLTS!
THIS CAN RESULT IN ASSEMBLY FAILURE!

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 13
SECTION 4 – GLIDE RIDE ASSEMBLY
Attach the Glide Ride to the Main Frame set up in Section 1 as shown in Figure 5
Figure 5

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 14
SECTION 5 - SLIDE ASSEMBLY (I)
Assemble the Slide as shown in Figure 6, 6a, and 6b.
Figure 6: Slide Steps Assembly Figure 6a: Slide Plate
Figure 6b: Slide Platform Assembly

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 15
SECTION 6 - SLIDE ASSEMBLY (II)
Figure 7: Slide Base Assembly
SECTION 7 - SLIDE ASSEMBLY (III)
Figure 8: Stabilising Tube Assembly

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 16
SECTION 8 - SLIDE ASSEMBLY (IV)
Assemble the Slide to the rest of the Swing Set as shown in Figure 9.
Figure 9
When the assembly has been done correctly, the 4-Piece Swing Set with Slide should
look like the Figure 10. Inspect all the components to see if they are properly and
securely assembled.
Figure 10

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 17
MAINTENANCE INSTRUCTION
To maximise the life of your swing set, make sure your children enjoy
your swing sets safely. It is important to check and inspect the following
regularly before each use of the swing set, and carry out necessary
maintenance immediately.
Nuts and Bolts: Check before each use for tightness and tighten if required. Replace any
damaged, distorted or missing fasteners immediately.
Plastic components: Check before each use for deterioration.
Replace immediately if cracked or damaged. Use only genuine Action’s replacement parts.
Metal components: Check before each use for corrosion, cracking, tears, distortion or other
damage. Replace immediately if these conditions exist. In particular, check the Brackets on
the Glide Ride and Lawn Swings, as these can be damaged through improper use / or
excessive lateral movement.
Oil all metallic moving parts at least one time a month.
CAUTION
Do not allow children to use the swing set until the maintenance has been carried
out. The use of swing set not in first class condition exposes the child to the risk
of injury. As a parent, supervisor, owner or guardian, it is your responsibility to
ensure that the swing set is properly maintained. Spare parts are available
through ACTION SPORTS Customer Service centre. Please call 1800 465 070
(Australia) or 09 488 4750 (New Zealand).

ACTION SPORTS EQUIPMENT PTY LIMITED – www.actionsports.com.au Page: 18
Swing Sets Limited Warranty
ACTION SPORTS warrants its swing set products to be free from defects in material and
workmanship under normal use and service conditions.
The various components of the swing set are warranted against defects and workmanship for
6 months.
All warranty coverage extends only to the original retail purchaser from the date of purchase.
ACTION SPORTS’ obligation under this Warranty is limited to replacing or repairing, at
ACTION’s option, the product or parts therein. Any enquiries relating to warranties or spare
parts must be directed to our Freecall 1800 465 070 (Australia) or Standard call 09 488
4750 (New Zealand). For efficient processing of your enquiry please have relevant date of
purchase, retailer name you purchased the item from and the brand on the product. This
warranty does not extend to any damage to a product caused by abuse, improper or abnormal
usage (as detailed in this instruction manual), or repairs not provided by ACTION. Nor does
this warranty extend to products used for commercial or rental purposes. This warranty does
not cover ordinary wear, tear and weathering, failure to follow directions, improper
installation, improper maintenance or acts of God (such as damage caused by storms,
lightning and by snow or ice). No other Warranty beyond that specifically set forth above is
authorised by ACTION.
Our sales and service centre has been set up to provide assembly assistance, replacement parts
and accessories, and to efficiently handle all warranty related matters.
Freecall 1800 465 070 (Australia) or email [e-mail]
Standard Call09 488 4750 (New Zealand)
Opening hours: 9am – 4:30pm Monday to Friday (excluding Public Holidays)
9am – 3pm Saturday
www.actionsports.com.au