ACU-RITE 01604 User manual

Instruction Manual
CONTENTS
Unpacking Instructions................2
Package Contents.......................2
Product Registration....................2
Features & Benefits: 3-in-1 ..........3
Features & Benefits: Display .......4
Setup ........................................6
3-in-1 Sensor Setup....................6
Display Setup.............................7
Set the Time, Date & Units...........8
Placement Guidelines .................9
3-in-1 Sensor Installation ..........10
Using the Weather Center.........11
Troubleshooting........................13
Care & Maintenance ................15
Calibration ..............................15
Replace Intelli-Time®Battery......16
Specifications...........................17
FCC Information.......................17
Customer Support ....................18
Warranty.................................18
Weather Center
model 01604 / 01645
Questions? Contact Customer Support at
[phone] or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.

2
Congratulations on your new AcuRite product. To ensure the best
possible product performance, please read this manual in its entirety
and retain it for future reference.
Unpacking Instructions
Remove the protective film that is applied to the LCD screen prior to using this
product. Locate the tab and peel off to remove.
Package Contents
1. Display
2. 3-in-1 Sensor
3. Sensor Mounting Bracket
4. Mounting Hardware
5. Power Adapter
6. Instruction Manual
PRODUCT MUST BE REGISTERED
IMPORTANT TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 year warranty protection
www.AcuRite.com

3
Features & Benets
4
1
2
3
6
5
3-in-1 SENSOR
1. Temperature & Humidity Sensors
(internal)
2. Release Lever for Battery Access
3. Mounting Point
4. Wind Speed Anemometer
5. Mounting Hardware
Includes anchors and screws.
Qty Diameter Length
4 #4 1”
1 #6 or #8 1/4” or 3/8”
6. Mounting Bracket
7. A-B-C Switch (not shown)
ID code that must match display’s
A-B-C switch to ensure units
synchronize.

4
Features & Benets
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
24
23
22
21
20
19
18
17
16
33
25
26
27
28
29
30
31
32
34

5
ox
ox
FRONT OF DISPLAY
1. Sensor Low Battery Indicator
2. Current Outdoor Temperature
Arrow icon indicates the direction
the temperature is trending.
3. Seasonal Information
Wind chill will show when
temperatures are below 40oF (4oC),
Dew Point when temperature is
41-79oF (5-26oC), and Heat Index
when temperature is over 80oF (27oC).
4. Average Wind Speed
Based on all wind speed readings
from the past 2 minutes.
5. Current Wind Speed
6. Learning Mode Icon
Disappears after weather forecast
self-calibration is complete.
7. 12 to 24 Hour Weather Forecast
Self-Calibrating Forecasting pulls data
from your sensor to generate your
personal forecast.
8. Humidity Level Indicator
Indicates a high or low indoor
humidity level.
9. Current Indoor Temperature
Arrow icon indicates the direction
the temperature is trending.
10. TODAY Icon
Indicates today’s records are being
viewed.
11. Moon Phase
12. ALL-TIME Icon
Indicates all-time records are being
viewed.
13. Icon
Indicates SET mode is active.
14. Intelli-Time®Clock
Automatically updates itself for
Daylight Saving Time.
15. Backlight Button
For momentary backlight and dimmer
settings.
16. AUTO DIM Mode Indicator (page 8)
17. Display Low Battery Indicator
18. Date
19. Current Indoor Humidity
Arrow icon indicates the direction
the humidity is trending.
20. Storm Indicator
Indicates a rapid drop in pressure
and probable storms.
21. Current Barometric Pressure
22. Peak Wind Speed
Highest speed from past 60 minutes.
23. Current Outdoor Humidity
Arrow icon indicates the direction
the humidity is trending.
24. Outdoor Sensor Signal Strength
BACK OF DISPLAY
25. Button
For setup preferences.
26. Button
For setup preferences.
27. Button
For setup preferences.
28. Button
Press to access all-time high and low
records.
29. A-B-C Switch
ID code that must match sensor’s
A-B-C switch to ensure units synchronize.
30. Reset Button
Full reset to factory defaults.
31. Intelli-Time® Battery Compartment
32. Battery Compartment
33. Plug-in for Power Adapter
34. Power Adapter
35. Battery Compartment Cover
(not shown)

6
•
•
ALKALINE
BATTERIES
Install Batteries
4 AA batteries
(700C) 158°F I
SETUP
3-IN-1 Sensor Setup
1
Set the A-B-C Switch
The A-B-C switch is located inside
the battery compartment. It can
be set to A, B or C. However,
you must select the same letter
choices for both the sensor and
the display in order for the units
to synchronize.
2
Install or Replace Batteries
AcuRite recommends high quality
alkaline or lithium batteries for
the best product performance.
Heavy duty or rechargeable
batteries are not recommended.
The 3-in-1 sensor requires lithium
batteries in low temperature
conditions. Cold temperatures
1. Press the release lever and pull
off the lower housing of the
sensor.
2. Remove the battery
compartment cover. Take
note of the A-B-C switch
setting inside the battery
compartment.
3. Insert 4 x AA batteries into
the battery compartment, as
shown. Follow the polarity
(+/-) diagram in the battery
compartment.
4. Replace the battery cover and
lower housing of the sensor.
can cause alkaline batteries to
function improperly. Use lithium
batteries in the 3-in-1 sensor for
temperatures below -4ºF / -20ºC.
2
A-B-C Switch
Set to match
display
A B C
1

7
•
• •
Display Setup
1 Set the A-B-C Switch
Locate the A-B-C switch inside
the battery compartment. Set
the A-B-C switch to A, B or C.
You must select the same letter
choices for both the display and
the sensor in order for the units
to synchronize.
2 Install or Replace Backup
Batteries (optional)
1. Remove the battery
compartment cover.
2. Insert 3 x AAA alkaline
batteries into the battery
compartment, as shown.
Follow the polarity (+/–)
diagram in the battery
compartment.
3. Replace the battery cover.
Plug in Power Adapter
For the best performance, plug
in the power adapter as the main
power source for this product.
3
1 A-B-C Switch
Set to match sensor
2 Install Backup Batteries (optional)
3 AAA batteries
A B C
IMPORTANT: Batteries are
a backup power source to
preserve records in the event of
a power outage. Power adapter
is recommended as the primary
power source to enjoy the full
functionality of this product.
3 Plug in Power Adapter
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to be
used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of used
batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries in fire,
as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT recharge
non-rechargeable batteries. DO NOT short-circuit the supply terminals.

8
ox
ox
ox
-'n-
'\{'
Set the Time, Date & Units
Press the “ ” button, located on the back of the display, to enter SET MODE.
Once in set mode, the preference you are currently setting will blink on the
display.
To adjust the currently selected (ashing) item, press and release the “ “ or
“ “ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ ” button again to adjust
the next preference. The preference set order is as follows:
TIME ZONE (EST CST MST PST AKT HAT AST)
DST (Daylight Saving Time ON or OFF)*
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (ºF or ºC)
PRESSURE UNITS (inHg or hPa)
WIND UNITS (MPH or KPH)
You will automatically exit SET MODE if no buttons are pressed for 10 seconds.
Enter setup mode at any time by pressing the “ ” button.
*If you live in an area that observes Daylight Saving Time, DST should be set
to ON, even if it is not currently Daylight Saving Time.
Display Backlight Settings
This weather station’s color display features three different lighting settings:
High (100%) brightness, Medium (60%) brightness and Low (30%) brightness.
Using battery power alone, the backlight is available momentarily for 10
seconds by pressing the “ ” button.
When display is powered with the power adapter, backlight remains on
at 100% brightness. Press “ ” button once to dim to 60% brightness;
press again to dim to 30%, press a 3rd time to enter “AUTO DIM” mode.
“AUTO DIM” icon appears below the clock.
AUTO DIM MODE: Automatically adjusts display brightness based on time of day & year.
MARCH 11- NOVEMBER 4 6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m.= 30% brightness
NOVEMBER 5 - MARCH 10 7:30 a.m. - 7:00 p.m.= 100% brightness
7:01 p.m. - 7:29 a.m. = 30% brightness

9
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display and the sensor are critical to the accuracy and
performance of this product.
Display Placement
Place the display in a dry area free of dirt and dust. To ensure
accurate temperature measurement, place out of direct sunlight
and away from heat sources or vents. Display stands upright for
tabletop use.
3-in-1 Sensor Placement
The 3-in-1 sensor is designed to remain outdoors all year long.
Choose an open location with no obstructions above or around the
sensor for the most accurate measurements.
Important Placement Guidelines
Display and sensor must be within 330 feet (100 m) of each other.
MAXIMIZE WIRELESS RANGE
Place units away from large metallic items, thick walls, metal surfaces, or other
objects that may limit wireless communication.
PREVENT WIRELESS INTERFERENCE
Place both units at least 3 feet (.9 m) away from electronic devices (TV,
computer, microwave, radio, etc.).
LOCATE AWAY FROM HEAT SOURCES
Position sensor away from heaters, air conditioners, chimneys, exhaust vents,
asphalt and concrete (surfaces that radiate heat).
LOCATE AWAY FROM HUMIDITY SOURCES
Avoid installing the sensor near pools, spas, or other bodies of water. Water
sources may impact humidity accuracy.
LOCATE AWAY FROM SPRINKLER HEADS
DO NOT install the sensor where it will be sprayed by a sprinkler system. This
may force water inside the sensor.
LOCATE AWAY FROM WIND OBSTRUCTIONS
DO NOT mount the sensor with obstructions around it.
Consider a location that is a wide open area, with few
structures around to ensure accurate wind speed measurement.
Visit us online to view installation photos and
video, or learn more about AcuRite technology:
www.AcuRite.com/3in1 View Video

10
Top Mount Side Mount
3-in-1 Sensor Installation Guidelines
INSTALLATION HEIGHT Mount the sensor at a minimum height of 5 feet (1.5 meters)
off the ground, in an open area. Higher is better for wind measurements - the
National Weather Service recommends 33 feet high!
MOUNTING OPTIONS The included mounting bracket it designed to screw directly
onto wooden posts or surfaces that are 2x4 or larger. The sensor can also be
mounted directly to common 3/4”
steel pipe (available at hardware
stores and home centers).
LEVEL INSTALLATION Use a
bubble level (not included) to ensure
level installation for accurate wind
measurement.
Top or Side Mount
1. Insert the mounting base into the
hole on the bottom of the sensor.
2. Use one of the screws included
in the hardware bag to fasten
the lower sensor housing to the
mounting base.
3. Fasten mounting base to a post or railing
using 2 screws.
Pipe Mount
1. Insert pipe or similar item all the way into
the hole on the bottom of the sensor. Note:
Mounting base is not used.
Pipe Mount
Do not install during
electrical storms.
Do not place pipe
or sensor near
electrical lines or
electrical equipment.
2. Use one of the screws included in the
hardware bag to fasten the lower sensor housing securely to the pipe.
The 3-in-1 sensor is now ready to use.
Basic Setup is Complete
The 3-in-1 sensor will now synchronize with the display. It may take a few minutes
for synchronization to complete. If both or one of the units appear to be functioning
improperly, please refer to the troubleshooting section.