Adance ADE-2022-C User manual

ADE- 2022-C Page 1 of 50
Maintenance Manual
Blast Chiller

ADE- 2022-C Page 2 of 50
Contents
ContentsContents
Contents Page
PagePage
Page
1
11
1 What is the Adande
®
System 4
2
22
2 Adande
®
Technology Ex lained 4
3
33
3 EC Declaration of Conformity 5
4
44
4 Storage of Product 6
5
55
5 O erating Adande
®
Tem erature Settings 6
5.1
5.15.1
5.1 The Dis lay Controls 6
5.2
5.25.2
5.2 Defrost 8
5.3
5.35.3
5.3 Drawer Alarm 8
5.4
5.45.4
5.4 Error Alarm 8
5.5
5.55.5
5.5 Tem erature Alarm 8
5.6
5.65.6
5.6 Electrical Connection 9
5.7
5.75.7
5.7 Location and Stability 10
6
66
6 Insulated Container Removal 11
7
77
7 Workto Removal 12
8
88
8 Front Grille removal 12
9
99
9 Left Hand Panel Removal 13
10
1010
10 Rear Panel Removal 13
11
1111
11 Drawer Front Removal 14
12
1212
12 Drawer Switch Re lacement 15
1
11
13
33
3 Removing the Diffuser 16
1
11
14
44
4 Eva orator Fan Re lacement 17
1
11
15
55
5 Secondary Blast Chill Fan Re lacement 18
16
1616
16 Drain Tray and Defrost Heater Removal and Re lacement 19
1
11
17
77
7 Eva orator Tem erature Probes Re lacement 20
1
11
18
88
8 Lid Heated Seal Re lacement 21
1
11
19
99
9 Seal Height Adjustment 22
20
2020
20 Runner Re lacement 23

ADE- 2022-C Page 3 of 50
2
22
21
11
1 Condenser Fan Re lacement 25
2
22
22
22
2 Electrical com onents 26
2
22
23
33
3 Electrical Control System 26
23.1
23.123.1
23.1 Wiring Diagram for Dixell XB570L Controller 28
2
22
24
44
4 How to enter setting on Dixell XB570L Blast Chill Controller 29
24.1
24.124.1
24.1 How to enter setting for each cycle 29
24.2
24.224.2
24.2 settings for Dixell XB570L Blast Chill Controller 30
2
22
25
55
5 Refrigeration Maintenance 34
2
22
26
66
6 Drawer configurations 35
2
22
27
77
7 Fault Finding 37
2
22
27
77
7.1
.1.1
.1 Drawers not o erating correctly 37
2
22
27
77
7.2
.2.2
.2 Seals and/or container rim have ice and condensation 37
2
22
27
77
7.3
.3.3
.3 Drawer is not maintaining set tem erature 37
2
22
27
77
7.4
.4.4
.4 The drawer does not ower u 38
2
22
27
77
7.
..
.5
55
5 Eva orator fans run when drawer is o en 38
2
22
27
77
7.6
.6.6
.6 Eva orator fans do not run when drawer is closed 38
27.7
27.727.7
27.7 Blast chill cycle fails to o erate 38
2
22
28
88
8 Ex loded diagrams 39
2
22
28
88
8.1
.1.1
.1 Housing S are Parts 39
2
22
28
88
8.2
.2.2
.2 Fridge Electrical System and Drawer Parts 40
2
22
28
88
8.3
.3.3
.3 Insulated Lid Parts 41
2
22
28
88
8.4
.4.4
.4 Base with Standard Castors Parts 42
2
22
28
88
8.5
.5.5
.5 High Castor Base Parts 43
2
22
28
88
8.6
.6.6
.6 Small Castor Base Parts 44
2
22
28
88
8.
..
.7
77
7 Double Wheel Castor Base Parts 45
2
22
28
88
8.
..
.8
88
8 Large Rollers and Feet Base Parts 46
2
22
28
88
8.
..
.9
99
9 Small Rollers and Feet Base Parts 47
2
22
28
88
8.
..
.10
1010
10 To Cover 48
2
22
28
88
8.
..
.1
11
11
11
1 Workto and U stand 49
2
22
28
88
8.
..
.1
11
12
22
2 Heat Shield workto 50

ADE- 2022-C Page 4 of 50
Welcome to Adande
Welcome to AdandeWelcome to Adande
Welcome to Adande®
®®
®
Refrigeration
RefrigerationRefrigeration
Refrigeration
1
11
1 What is Adande®
What is Adande®What is Adande®
What is Adande®
Adande
®
is a new method of cold storage develo ed as a series of refrigerated drawers
that offer storage tem erature flexibility in 1ºC increments between –22ºC and +15ºC.
Each refrigerated drawer:-
•Provides stable tem erature storage
•A removable container to act as tem orary cool and safe roduct storage.
•Gives full lan area access roviding s ace efficient storage.
•Is easily cleaned or re laced.
•Can be su lied configured as a blast chiller.
2
22
2 Adande® Ex lained
Adande® Ex lainedAdande® Ex lained
Adande® Ex lained
Adande
®
uses standard technology and refrigeration arts but in a com letely new
and atented way.
A dedicated fridge engine su lies refrigerant to an eva orator coil assembly. The
eva orator coil assembly then su lies cooling to the insulated container and is sized
to maintain u to 40kg of roduct at any set oint tem erature, in the range of –22ºC
to +15ºC.
Figure 1: Front view of Adande
®
Single Drawer

ADE- 2022-C Page 5 of 50
3
3 3
3 EC Declaration of Conformit
EC Declaration of ConformitEC Declaration of Conformit
EC Declaration of Conformity
yy
y
We declare that the following machinery com lies with the essential health and
safety requirements of the :-
The Machinery Directive 2006/42/EC.
The Low Voltage Directive 2006/95/EEC.
The Electromagnetic Com atibility Directive 2004/108/EC.
The Pressure Equi ment Directive 97/23/EC.
Machinery Descri tion: 1 Drawer A liance for Chilled Storage.
Make: Adande
®
.
Ty e: Adande unitary drawer refrigeration
Manufactured by Adande Refrigeration Ltd.,
45 Pinbush Road, South Lowestoft Industrial Estate, Lowestoft, Suffolk
NR33 7NL
The following trans osed harmonised Euro ean Standards have been used:
EN ISO 12100 arts 1 & 2 Safety of Machinery – Basic conce ts, general rinci les
for design.
EN ISO 13857 Safety of Machinery – Safety distances to revent danger zones
being reached by the u er and lower limbs.
EN ISO 13732-1: 2006 Ergonomics of the thermal environment -- Methods for the assessment of human res onses to contact with surfaces -
- Part 1: Hot surfaces .
EN 1672-2 Food rocessing machinery – Basic conce ts – Part 2 : Hygiene
requirements
EN 61000-6-3:2001, Electromagnetic com atibility (EMC) - Part 6-3: Generic
standards; Emission standard for residential, commercial and light- industrial
environments
EN 61000-6-1 Generic Immunity Standard; Residential commercial and light
industrial environments.
EN 60335-2-24 The Safety of Household and Similar Electrical A liances – Part 2
–24: Particular Requirements for Refrigerating A liances and Ice Makers.
EN 60335-2-89:2010 Household and Similar Electrical A liances – Safety - Part
2 –89: Particular Requirements for commercial refrigerating a liances with an
incor orated or remote refrigerant condensing unit or com ressor.
The technical file for this machinery will be re ared on demand by :-
Name: Ian Wood
Position: Managing Director
Who also signs on behalf of the manufacturer
ADANDE
®
REFRIGERATION
45 Pinbush Road
South Lowestoft Industrial Estate
Lowestoft
Suffolk
NR33 7NL.

ADE- 2022-C Page 6 of 50
4
44
4 Storage of Product
Storage of ProductStorage of Product
Storage of Product
For the drawer to o erate at full efficiency the heated seal should be maintained in
good condition. It is essential that the roduct is not stored above the “MAX FILL
“MAX FILL “MAX FILL
“MAX FILL
LEVEL”
LEVEL”LEVEL”
LEVEL” line as this can damage the seal and affect the o eration of the drawer.
The drawer is ca able of storing any food roduct. However, roducts which may give
off acidic odours like vinegar, onions, etc. should be suitably sealed. Adande
®
also
recommends storage containers with liquid food roducts be stored with lids.
Ensure that the roduct is never stacked above the “MAX FILL LEVEL”
“MAX FILL LEVEL”“MAX FILL LEVEL”
“MAX FILL LEVEL” Label in the
insulated container.
5
55
5 O erating Adande
O erating AdandeO erating Adande
O erating Adande
®
®®
®
Tem erature Control
Tem erature ControlTem erature Control
Tem erature Control System
SystemSystem
System
The Adande
®
tem erature control system allows you to set and control the drawer
within a tem erature range of -22°C ( -8°F) and +15°C (59°F).
Tem erature accuracy in the drawer will be maintained within ±2ºC of the set oint
5.1
5.15.1
5.1 The Dis lay C
The Dis lay CThe Dis lay C
The Dis lay Controls
ontrolsontrols
ontrols
Increase/
Decrease set oint
tem erature
Insertion Probe not used
Ignore this tem erature
in Yellow
Cycle
numbers
Hold mode
Sta
rt/ Sto
Cycle and hold
mode selection

ADE- 2022-C Page 7 of 50
To Blast Chill
To Blast ChillTo Blast Chill
To Blast Chill
1. To sto the cycle ush and hold the START/ STOP button until
the yellow light turns off.
2. Push and release the button until the desired cycle is selected.
The cycle number selected will be highlighted.
Cycle
CycleCycle
Cycle Blast
Blast Blast
Blast
mode
modemode
mode
1
11
1
st
stst
st
Phase
Phase Phase
Phase -
--
- Hard Chill
Hard ChillHard Chill
Hard Chill 2
22
2
nd
ndnd
nd
Phase
Phase Phase
Phase -
--
- Soft Chill
Soft ChillSoft Chill
Soft Chill Total
Total Total
Total
cycle
cycle cycle
cycle
duration
duration duration
duration
(min)
(min)(min)
(min)
Duration
(min)
Tem erature
(°C)
Duration
(min)
Tem erature
(°C)
1
11
1 Soft Chill 90 -1 90
2
22
2 Hard Chill 60 -15 30 -1 90
3
33
3 Soft Chill 120 -1 120
4
44
4 Hard Chill 80 -15 40 -1 120
3. Push and release the START/ STOP button the yellow light will
be switched on indicating that the blast chill cycle has started.
Normal O eration
Normal O erationNormal O eration
Normal O eration
For normal refrigeration or frozen storage
normal refrigeration or frozen storagenormal refrigeration or frozen storage
normal refrigeration or frozen storage ush button until the ‘H’
‘H’‘H’
‘H’
a ears on the dis lay and no cycle numbers are lit.
To change tem erature ush and release the button this will show the current
set oint.
Then ush and hold down the button and the word “SetH”
“SetH”“SetH”
“SetH” will flash
Use the and buttons to either increase or decrease the set oint
tem erature.
Push the button again to store the new set oint. If the set button is not
ressed the tem erature will revert back to revious setting.
Press to activate the hold mode, the buttons and will be
illuminated.

ADE- 2022-C Page 8 of 50
5.2
5.25.2
5.2 Defrost
DefrostDefrost
Defrost
The refrigeration system automatically defrosts. If a manual defrost is required then
ress the manual defrost button/tem erature u button for 3 seconds.
5.
5.5.
5.3
33
3 Drawer Alarm
Drawer AlarmDrawer Alarm
Drawer Alarm
If the drawer is o en for more than 10 minutes, the dis lay in the control anel
changes to “
““
“DA
DADA
DA”.
”.”.
”.
When the alarm has been activated, the Adande
®
drawer will alarm both visually and
audibly.
To silence the audible alarm, ress ANY button on the dis lay, or close the drawer. The
alarm light and flashing dis lay will continue to show until the drawer has been fully
closed.
NOTE: THERE IS NO
NOTE: THERE IS NO NOTE: THERE IS NO
NOTE: THERE IS NO COOLING TO
COOLING TOCOOLING TO
COOLING TO THE INSULATED CONTAINER
THE INSULATED CONTAINER THE INSULATED CONTAINER
THE INSULATED CONTAINER WHEN THE
WHEN THE WHEN THE
WHEN THE
DRAWER IS OPEN.
DRAWER IS OPEN.DRAWER IS OPEN.
DRAWER IS OPEN.
5.
5.5.
5.4
44
4 Error Alarm
Error AlarmError Alarm
Error Alarm
If dis lay reads “
““
“rPF
rPFrPF
rPF”
””
” or “
““
“EPF
EPFEPF
EPF”
””
”, a tem erature robe has failed, and an engineer should
be called.
The Adande
®
drawer will o erate with a 15 minute on / 15 minute off cycle in the event
of an “
““
“rPF
rPFrPF
rPF”
””
” failure. This will hel to maintain the stored roduct at a safe tem erature,
but recise tem erature control will be lost. “
““
“E
EE
EPF
PFPF
PF”
””
” will only affect defrosts, and these
will be timed to maintain o eration of the drawer. An engineer should be called as
soon as ossible for either fault.
5.
5.5.
5.5
55
5 Tem erature Alarm
Tem erature AlarmTem erature Alarm
Tem erature Alarm
Should “H
“H“H
“HA
AA
A”
””
” a ear on the dis lay, the drawer tem erature has exceeded its set oint
by 7°C and roduct core tem erature should be checked. If the Adande
®
drawer has
recently been turned on, loaded with warm roduct or left o en for a long eriod of
time, this alarm may be dis layed. If the tem erature does not return to the set oint
tem erature, an engineer should be called.
Should “L
“L“L
“LA
AA
A”
””
” a ear on the dis lay, the drawer tem erature has fallen below its set
oint by 7°C and roduct core tem erature should be checked. If the Adande
®
drawer’s tem erature set oint has recently been increased, this alarm may be
dis layed. If the tem erature does not return to the set oint tem erature, an engineer
should be called.

ADE- 2022-C Page 9 of 50
5.6
5.65.6
5.6 Electrical Connection
Electrical ConnectionElectrical Connection
Electrical Connection
The Adande
®
drawer should be connected to a 230V, single hase, 50 Hz, standard
socket outlet su ly. The drawer is connected to the mains su ly with a detachable
su ly lead, one end of which is fitted with a standard 13 am 3 in lug (fused at 13A).
The other end of the su ly lead, fitted with an a liance lug, is connected to the
Adande
®
drawer as shown in figure 3a below.
Figure 3a: Mains connection oint
The unused socket on the right hand side in figure 3a can be used to rovide a mains
su ly to additional Adande
®
Drawers as shown in figure 3b below.
Figure 3b: Mains connection oint
DO NOT REMOVE ACCESS PANELS WITH
DO NOT REMOVE ACCESS PANELS WITH DO NOT REMOVE ACCESS PANELS WITH
DO NOT REMOVE ACCESS PANELS WITH THE ELECTRICAL SUPPLY CONNECTED.
THE ELECTRICAL SUPPLY CONNECTED.THE ELECTRICAL SUPPLY CONNECTED.
THE ELECTRICAL SUPPLY CONNECTED.
Unique Serial
number of the
unit: This
should be
quoted when
requesting a
service visit
Single
‘P’cli for
retaining
mains
cable

ADE- 2022-C Page 10 of 50
5.7
5.75.7
5.7 Location and Stability
Location and StabilityLocation and Stability
Location and Stability
It is im ortant that the Adande
®
drawer is installed and maintained on a flat, clean and
level surface
level surfacelevel surface
level surface to ensure correct o eration.
The room should be dry and sufficiently ventilated.
O timum erformance is obtained at ambient tem eratures between +16ºC (60ºF)
and +38ºC (100ºF).
The air outlet grill MUST be ke t clear at all times to maintain o timum
The air outlet grill MUST be ke t clear at all times to maintain o timum The air outlet grill MUST be ke t clear at all times to maintain o timum
The air outlet grill MUST be ke t clear at all times to maintain o timum
erform
erformerform
erformance.
ance.ance.
ance.
The Adande
®
drawer can be mounted on rubber feet, rollers or castors. When
mounted on a castor base, the front two castors should have their brakes ON during
normal use as in figure 4 .
Figure 4: Lockable Castor
If the Adande
®
drawer is mounted on two rollers at the rear and rubber feet at the
front, then to move the drawer either lift the front as shown in figure 5 and ush or
ull into osition, or use an o en drawer as a lever to lift the drawer as shown in figure
6,
this method may be referable if drawers are stacked more than one high.
Figure 5 Figure 6
THE
THE THE
THE INSULATED CONTAINER
INSULATED CONTAINERINSULATED CONTAINER
INSULATED CONTAINER SHOULD BE UNLOADED BEFORE MOVING
SHOULD BE UNLOADED BEFORE MOVINGSHOULD BE UNLOADED BEFORE MOVING
SHOULD BE UNLOADED BEFORE MOVING

ADE- 2022-C Page 11 of 50
6
66
6Insulated
Insulated Insulated
Insulated Container
ContainerContainer
Container Removal
RemovalRemoval
Removal
For many of the maintenance rocedures the insulated container will need to be
removed to allow for access. To remove the insulated container, first ull the drawer
out fully so that the rear edge of the container clears the front and the runners are
fully extended. Then as the hoto below shows (figure 7) lift the container vertically u
to remove (two eo le should lift the container out if still filled with roduct).
Figure 7: Removing the insulated container

ADE- 2022-C Page 12 of 50
7 Workto Re
Workto ReWorkto Re
Workto Removal
movalmoval
moval
To remove the workto , first remove the 4 off M5 X10 bolts from the rear of the
drawer, lift the rear of the workto and ush slightly forward to slide over and clear
from the front retaining slots (figure 8) . Re lacement is the reverse of the removal
rocedure.
NOTE:
NOTE: NOTE:
NOTE: CORRECT LIFTING PROCEDURES SHOULD BE FOLLOWED
CORRECT LIFTING PROCEDURES SHOULD BE FOLLOWEDCORRECT LIFTING PROCEDURES SHOULD BE FOLLOWED
CORRECT LIFTING PROCEDURES SHOULD BE FOLLOWED
Figure 8: Workto removal
8 Front Grille Removal
Front Grille RemovalFront Grille Removal
Front Grille Removal
To gain access to the electrical com onents it is necessary to remove the front grille,
to do this first remove the insulated container from the drawer, loosen the 2 off M5 X 8
ST/ST bolts located inside the drawer s ace, and loosen the 2 off M5 X 8 ST/ST screws
located externally at the side of the drawer. The front grille can now be removed by
ulling forward at the bottom and then down. (figures 9/10).
NOTE: POWER MUST BE ISOLATED BEFORE REMOVING ANY PANELS
NOTE: POWER MUST BE ISOLATED BEFORE REMOVING ANY PANELSNOTE: POWER MUST BE ISOLATED BEFORE REMOVING ANY PANELS
NOTE: POWER MUST BE ISOLATED BEFORE REMOVING ANY PANELS
Loosen:
2 x Screws
2 x Bolts
Figure 9 Figure 10

ADE- 2022-C Page 13 of 50
9
99
9Left Hand Panel Removal
Left Hand Panel RemovalLeft Hand Panel Removal
Left Hand Panel Removal
To gain access to the com ressor, the left hand anel must be removed from the
drawer, to remove this anel the 4 off M5 X 8 ST/ST screws on the side of the drawer
and 2 off M5 X 8 bolts from the rear of the drawer must be removed as shown in figure
11
, then slide the anel down and out.
Remove 4x screws and 2x bolts
Figure 11: LH side fridge engine access anel removal
10
1010
10 Rear Panel Removal
Rear Panel RemovalRear Panel Removal
Rear Panel Removal
The rear anel of the drawer may require removal to gain access to the drain i e or
assist in diffuser and heated seal re lacements. To remove the back anel, remove all
13 off M5x10 ST/ST bolts as shown in figure 12 below.
Figure 12: Rear anel removal

ADE- 2022-C Page 14 of 50
1
11
11
11
1Drawer Front Removal
Drawer Front RemovalDrawer Front Removal
Drawer Front Removal
To remove the drawer front you will need to remove the 4 off M5 Br.Zn.Pd. Nyloc nuts
and 4 off M5 X 10 St/Steel bolts as shown in figure 13 below.
NOTE: WHEN REPLACING DRAWER FRONT LOCTITE SHOULD BE USED ON
NOTE: WHEN REPLACING DRAWER FRONT LOCTITE SHOULD BE USED ON NOTE: WHEN REPLACING DRAWER FRONT LOCTITE SHOULD BE USED ON
NOTE: WHEN REPLACING DRAWER FRONT LOCTITE SHOULD BE USED ON
THE SCREWS
THE SCREWSTHE SCREWS
THE SCREWS
Figure 13: Removing the four nyloc nuts and four bolts
Once these fixings are removed the drawer front will now slide off as shown below in
figure 14
below.
Figure 14: Removing the drawer front

ADE- 2022-C Page 15 of 50
1
11
12
22
2 Drawer Switch
Drawer SwitchDrawer Switch
Drawer Switch Re lacement
Re lacementRe lacement
Re lacement
To gain access and/or re lace the drawer switch, remove either the insulated
container and workto (Cha ter 6 and 7) or the Insulated container and side anel
(Cha ters 6 and 9).
Remove the S ade Connectors from the back of the switch and ush the switch
through into the drawer cavity as shown in figure 15 and 16 .
Figure 15: S ade connectors connected to the drawer switch
Figure 16: Drawer switch mounted on the Inner Wall Side Panel

ADE- 2022-C Page 16 of 50
1
11
13
33
3 Removing the Diffuser
Removing the DiffuserRemoving the Diffuser
Removing the Diffuser
To remove the diffuser the Insulated container will first need removing to allow access
(Cha ter 6). To remove the diffuser from the lid the 4 off lastic ozi screws and 4 off
slotted ST/ST screws will need removing as shown in figure 17. This will allow the
diffuser to be lowered for access.
NOTE: THE DIFFUSER WILL BE CONNECTED TO THE
NOTE: THE DIFFUSER WILL BE CONNECTED TO THE NOTE: THE DIFFUSER WILL BE CONNECTED TO THE
NOTE: THE DIFFUSER WILL BE CONNECTED TO THE DRAWER
DRAWERDRAWER
DRAWER BY THE
BY THE BY THE
BY THE
EVAPORATOR FAN WIRES
EVAPORATOR FAN WIRESEVAPORATOR FAN WIRES
EVAPORATOR FAN WIRES AND SECONDARY AIR
AND SECONDARY AIRAND SECONDARY AIR
AND SECONDARY AIR CIRCULATION FAN WIRES
CIRCULATION FAN WIRESCIRCULATION FAN WIRES
CIRCULATION FAN WIRES
Figure 17: Lid Diffuser

ADE- 2022-C Page 17 of 50
1
11
14
44
4 Eva orator Fan Re lacement
Eva orator Fan Re lacementEva orator Fan Re lacement
Eva orator Fan Re lacement
Once the diffuser is removed, the small eva orator fans can be removed first by
cutting the wires at the FAN
FANFAN
FAN end and use these to ull through the wires attached to
the new fan. Now remove the four self ta ing screws that hold the fan in lace as
shown in figure 17a .
The fan wires need to be disconnected from the 12volt ower su ly within the
controller enclosure, ulling the new wires through the hole in the lid (as shown in
figure 16c below) fit bullet crim s to the new fan wires and connect to the 12volt
ower su ly, mount the fans back on the diffuser as shown below in figure 17b .
Re lace all cable ties.
Figure 17a: Eva orator fans
4 Off er Fan Self Ta ing screws hole in lid for all wiring
Figure 17b Figure 17c

ADE- 2022-C Page 18 of 50
15
1515
15 Secondary Blast Chill Fan Re lacement.
Secondary Blast Chill Fan Re lacement.Secondary Blast Chill Fan Re lacement.
Secondary Blast Chill Fan Re lacement.
Once the diffuser is removed, the secondary blast chill fans can be accessed for
removal first by cutting the wires at the F
FF
Fan
an an
an end and use these to ull through the
wires attached to the new fan. Now remove the four screws that hold the fan and
guard in lace as shown in figure 18.
The fan wires need to be disconnected from the 24volt ower su ly within the
controller enclosure, ulling the new wires through the hole in the lid (as shown in
figure 17c ) fit bullet crim s to the new fan wires and connect to the 24volt ower
su ly, mount the fans back on the diffuser as shown below in figure 18 . Re lace all
cable ties
4 off eva orator fans
2 off Secondary blast chill fans and associated guard
Figure 18: Diffuser showing eva orator fans, secondary blast chiller fans and 8 off
diffuser retaining screws

ADE- 2022-C Page 19 of 50
1
11
16
66
6 Drain Tray
Drain TrayDrain Tray
Drain Tray and
and and
and Defrost Heater
Defrost Heater Defrost Heater
Defrost Heater Removal
Removal Removal
Removal a
aa
and
ndnd
nd Re lacement
Re lacementRe lacement
Re lacement
To remove the drain tray the insulated container, rear anel and diffuser will need to
be removed. (Refer to cha ters 6, 10 & 13) Once this has been done remove the drain
i e and utty from the back of the lid as shown in figure 19 below.
Now remove the wires for the defrost heater from the controller. (Refer to Cha ters 21
and 22)
NOTE: ATTACH A SPARE PIECE OF
NOTE: ATTACH A SPARE PIECE OF NOTE: ATTACH A SPARE PIECE OF
NOTE: ATTACH A SPARE PIECE OF DRAW WIRE TO THE OLD HEATER WIRES
DRAW WIRE TO THE OLD HEATER WIRES DRAW WIRE TO THE OLD HEATER WIRES
DRAW WIRE TO THE OLD HEATER WIRES
BEFORE PULLING WIRES
BEFORE PULLING WIRES BEFORE PULLING WIRES
BEFORE PULLING WIRES OUT
OUTOUT
OUT TO AID PULLING THROUGH NEW
TO AID PULLING THROUGH NEW TO AID PULLING THROUGH NEW
TO AID PULLING THROUGH NEW HEATER
HEATER HEATER
HEATER
WIRES.
WIRES.WIRES.
WIRES.
Figure 19: Drain i e and utty
Remove the four M5 X 10 bolts and associated sealing washers fixing the drain tray to
the eva orator, dro down the drain tray com lete with defrost heater and remove.
(figure20)
Figure 20: Remove four bolts and sealing washers to release drain tray note osition of
2 diffuser retaining brackets
When re lacing the drain tray take care not to bend the tray or the water may not
drain correctly, ensure all four sealing washers are on the four fixing bolts. Re lace
drain tray and a ly utty around drain i e enetration both inside and outside of lid.

ADE- 2022-C Page 20 of 50
1
11
17
77
7 Eva orator Tem erature Probes
Eva orator Tem erature ProbesEva orator Tem erature Probes
Eva orator Tem erature Probes Re lacement
Re lacement Re lacement
Re lacement
To re lace a faulty tem erature robe the insulated container, diffuser and drain tray
will need to be removed. (Refer to cha ters 6, 13 & 15) to gain access to the eva orator
coil. Remove the P-Cli s holding the robes in lace and the refrigeration utty from
wire enetration in lid.
Disconnect the faulty robe from the controller, ull the robe wires through the lid
and remove from the drawer. Install the new robes back through the electrical wire
enetration hole in the lid and re connect to controller, re lace the P-Cli s as shown
in figure 21 and re air/re lace the refrigeration utty at the wire enetration of the lid.
T1 Drawer
Tem erature robe
T2 Defrost robe
Figure 21: Tem erature robes held in lace with P-Cli s