Adaptica 2WIN User manual

BATTERY CHARGER
USER MANUAL

1
INDEX
Warnings pg. 2-4
Set Up pg. 5
Led Information pg. 6
Label and Symbol pg. 7-8
Technical Information pg. 9-10
EMC Tables pg. 11-16

2
WARNINGS
READ CAREFULLY THE
OPERATING MANUAL OF 2WIN
BEFORE USING THE BATTERY
CHARGER
THIS DEVICE MUST NOT BE USED
IN OXYGEN RICH
ENVIRONMENTS OR IN PRESENCE OF
FLAMMABLE PRODUCTS
TO REDUCE THE RISK OF
INJURY, CHARGE ONLY BATTERY
MODEL CS-SP112XL AND PSP110ML

3
THIS DEVICE IS DESIGNED TO BE
USED INDOOR. DO NOT EXPOSE
TO WATER: THIS COULD LEAD TO
ELECTRIC SHOCK
USE ONLY WITH ACCESSORIES
SUPPLIED BY ADAPTICA (USB
CABLE, WALL ADAPTER)
NO MODIFICATION OF THIS
EQUIPMENT IS ALLOWED. ONLY
TECHNICIANS AUTHORIZED BY THE
MANUFACTURER MAY SERVICE THE
DEVICE

4
The device has been tested and
found to comply to the limits for
medical devices contained in
IEC60601-1-2.
The device may cause radio
interference or may disrupt the
operation of nearby equipment.
It may be necessary to take
mitigation measures, such as re-
orientering or relocating the
2WIN Battery Charger or shielding the
location.

5
SET UP
Insert USB type-C
cable into the
charger, and
connect it to power
supply
Insert the battery
inside the charger
Extract the battery
and use it in the
2WIN

6
LED INFORMATION
Red Led: battery is
charging
Green Led: battery is
charged
Led off: no battery or
damaged battery
Green Led: Power on
Led off: no power

7
LABEL AND SYMBOLS
Electronic device
subject to the WEEE
Directive on waste
disposal

8
CE Marking
Manufacturer ID
Read user manual
Date of
manufacturing

9
TECHNICAL INFORMATION
•AC/DC 110/240 VAC, 50/60 Hz
•Power cable: USB type-C standard
cable
•Cable min-max length: 1-1.5 m
•Weight: 70 g
•Battery type: CS-SP112XL and PSP–S110
•Battery charger size: 6.5 X 7.0 X 2.5 mm
•Rated Voltage: 5 V

10
•Standard charge: CC-CV method with
charge current of 600 mA
•Maximum operating temperature: 25°C
•The battery charger can be attached
to metallic surfaces

11
EMC TABLES
Guidance and manufacturer’s declaration –
electromagnetic emissions
The 2WIN Battery Charger is intended for use in the
electromagnetic environment specified below.
The customer or the user of the 2WIN Battery Charger
should assure that it is used in such an environment.
Emissions
tests
Compliance
Electromagnetic
environment –guidance
RF
emissions
CISPR 11
Group 1
The 2WIN Battery Charger
uses RF energy only for its
internal function.
Therefore, its RF emissions
are very low and are not
likely to cause any
interference in nearby
electronic equipment.

12
RF
emissions
CISPR 11
Class B
The 2WIN Battery Charger
is suitable for use in all
establishments, including
domestic establishments
and those directly
connected to the public
low voltage power supply
network that supplies
buildings used for
domestic purposes.
Harmonic
emissions
IEC 61000-
3-2
Not
applicable
Voltage
fluctuations
/ flicker
emissions
IEC 61000-
3-3
Complies

13
Guidance and manufacturer’s declaration –
electromagnetic immunity
The 2WIN Battery Charger is intended for use in the
electromagnetic environment specified below.
The customer or the user of the 2WIN Battery Charger
should assure that it is used in such an environment.
Immunity
test
IEC 60601
test level
Complia
nce
Electromagneti
c environment –
guidance
Electrostatic
discharge
(ESD)
IEC 61000-4-
2
±6 kV
contact
±8 kV air
Complie
s
Floors should be
wood, concrete
or ceramic tile. If
floors are
covered with
synthetic
material, the
relative humidity
should be at
least 30 %.

14
Electrical
fast
transient/bu
rst IEC
61000-4-4
±2 kV for
power
supply
lines
±1 kV for
input/out
pour lines
Complie
s
Mains power
quality should
be that of a
typical
commercial or
hospital
environment.
Surge
IEC 61000-4-
5
±1 kV
line(s) to
line(s)
±2 kV
line(s) to
earth
Complie
s
Mains power
quality should
be that of a
typical
commercial or
hospital
environment.
Voltage dips,
short
interruptions
and voltage
variations
<5 % UT
(>95 % dip
in UT)
for 0,5
cycle
Complie
s
Mains power
quality should
be that of a
typical
commercial or

15
on power
supply input
lines IEC
61000-4-11
40 % UT
(60 % dip
in UT)
for 5
cycles
70 % UT
(30 % dip
in UT)
for 25
cycles
<5 % UT
(>95 % dip
in UT)
for 5 s
hospital
environment. If
the user of the
2WIN Battery
Charger requires
continued
operation during
power mains
interruptions, it is
recommended
that the 2WIN
Battery Charger
be powered
from an
uninterruptible
power supply or
a battery

16
NOTE UTis the a.c. mains voltage prior to application
of the test level.

STESK00018_V0
Adaptica Srl
Via San Marco 9/H, 35129 Padova (PD), Italy
[email protected]
www.adaptica.com