Schumacher Electric SE-2352-CA User manual

0099001383-02
OWNERS MANUAL
MANUAL DEL USUARIO
PLEASE SAVE THIS OWNERS MANUAL AND READ BEFORE EACH USE. This manual
will explain how to use the battery charger safely and effectively. Please read and follow these
instructions and precautions carefully.
POR FAVOR CONSERVE ESTE MANUAL DEL USUARIO Y LEALO ANTES DE CADA
USO. En este manual le explica cómo utilizar el cargador de batería de manera segura y
Model / Modelo:
SE-2352-CA
Automatic Battery Charger
Cargador de baterías automático

CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ........................................................................3
PERSONAL SAFETY PRECAUTIONS...........................................................................3
ASSEMBLY INSTRUCTIONS.........................................................................................4
GROUNDING AND AC POWER CORD CONNECTIONS .............................................5
CONTROL PANEL..........................................................................................................5
OPERATING INSTRUCTIONS.......................................................................................5
MAINTENANCE AND CARE ..........................................................................................7
TROUBLESHOOTING....................................................................................................7
BEFORE RETURNING FOR REPAIRS..........................................................................8
LIMITED WARRANTY ....................................................................................................8
WARRANTY CARD / TARJETA DE GARANTÍA...........................................................17
CONTENIDOS
INSTRUCCIONES IMPORTANTES DE SEGURIDAD ...................................................9
PRECAUCIONES DE SEGURIDAD PERSONAL ........................................................10
INSTRUCCIONES DE MONTAJE ................................................................................10
CONEXIONES A TIERRA Y ENERGÍA DE CA............................................................. 11
PANEL DE CONTROL.................................................................................................. 11
INSTRUCCIONES DE OPERACIÓN............................................................................12
MANTENIMIENTO Y CUIDADO...................................................................................13
LOCALIZACIÓN Y RESOLUCIÓN DE PROBLEMAS ..................................................14
ANTES DE DEVOLVER A REPARACIONES ...............................................................14
GARANTÍA LIMITADA...................................................................................................15
WARRANTY CARD / TARJETA DE GARANTÍA...........................................................17

3
IMPORTANT SAFETY INSTRUCTIONS
WARNIN  RIS OF EPLOSIVE ASES
WORKING IN THE VICINITY OF A LEAD-ACID BATTERY IS DANGEROUS. BATTERIES
IT IS IMPORTANT THAT YOU FOLLOW THESE INSTRUCTIONS EACH TIME YOU USE
THE CHARGER.
To reduce the risk of a battery explosion, follow these instructions and those published
by the manufacturer of the battery and any equipment you intend to use in the vicinity
of the battery. Review the cautionary markings on these products and on the engine.
WARNING: Pursuant to California Proposition
the State of California to cause cancer and
birth defects or other reproductive harm.
Wash hands after handling.
Use the battery charger on LEAD-ACID and
AGM-type rechargeable batteries with
recommended rated capacities of 22-59Ah
etc. This charger is not intended to supply
than in a motor-starting application.
WARNING: Do not use battery charger with
dry cell batteries that are commonly used with
home appliances. These batteries may burst
and cause injury or damage to property.
Use only attachments recommended or sold
by the battery chargers manufacturer. Use
of non-recommended attachments may
Locate the battery chargers power cord so
subjected to damage or stress.
Do not operate the charger if it has received
professional for inspection and repair.
Keep out of reach of children.
the charger from the outlet before
attempting any maintenance or cleaning.
Do not use an extension cord.
Always charge the battery in a well-
ventilated area
WARNING: RISK OF EXPLOSIVE GAS.
Operate the charger as far away from the
battery as DC charger cables permit.
Do not expose the charger to rain or snow.
NEVER charge a frozen battery.
NEVER set a battery on top of the charger.
NEVER place the charger directly above a
battery being charged. Gases from the
battery will corrode and damage the charger.
NEVER touch the battery clamps together
when the charger is energized.
cord may cause damage to the cord or plug.
Do not operate the charger with damaged
cord or plug.
NEVER allow battery acid to drip onto the
charger.
NEVER overcharge a battery.
PERSONAL SAFETY PRECAUTIONS
Wear complete eye protection and
lead-acid batteries. Always have someone
nearby for help.
medical attention.
minutes and get medical attention.
Neutralize any acid spills thoroughly with
Remove all personal metal items from your
and watches. A battery can produce a short
circuit current high enough to weld a ring to
NEVER
the vicinity of the battery or engine.
Do not drop a metal tool onto the battery.
If it is necessary to remove the battery from

4
ASSEMBLY INSTRUCTIONS
It is important to fully assemble your charger before use. Remove all cord wraps and
uncoil the cables prior to using the battery charger. Follow these instructions for assembly.
PARTS TOOLS NEEDED
2 10-24 x 5/8 thread cutting screws
(2) wheels
(1) axle
(2) axle caps
(1) handle
(1) foot
3/8" wrench (for mounting foot)
5/16" wrench (for mounting wheels)
1/4" wrench (for mounting handle)
hammer
Phillips-head screwdriver
1. Attach the foot:
Remove the
charger from the
and place upside
surface. Attach
the foot and
secure it with the two 10-24 x 5/8 thread
cutting screws provided.
2. Assemble the wheels and axle: Hold
one of the axle caps onto the top end of
the axle. Be sure to tap the axle cap on
straight. Slide both wheels onto the axle
with the recessed hubs facing out as
shown. Install the second axle cap.
3. Mount the axle to the charger: Place
the bottom of the charger. Place the axle
cutting screws provided.
NOTE: Be careful not to drop the
4. Attach the handle: Turn the charger right
side up onto its foot and wheels. Remove
the two top screws from each side of the
charger. Align the handle so the screw
holes are aligned with the screw holes
on each side
of the charger.
Attach the
handle using
the same
screws you
previously
removed.

5
GROUNDING AND AC POWER CORD CONNECTIONS
This battery charger is for use on a nominal
120 volt circuit and has a grounded plug.
plugged into an outlet that is properly
installed and grounded in accordance with
all local codes and ordinances. The plug
use with an ungrounded system.
NOTE:
use of an adapter plug is not allowed in
Canada. Use of an adapter plug in the
United States is not recommended and
should not be used.
USING AN EXTENSION CORD
The use of an extension cord is not
recommended. If you must use an
Pins on plug of extension cord must be the
plug on charger.
Ensure that the extension cord is properly
wired and in good electrical condition.
Wire size must be large enough for the AC
Length of cord (feet) 25 50 100 150
AWG* size of cord 14 12 10 8
*AWG-American Wire Gauge
CONTROL PANEL
ON/OFF SWITCH
Use this switch to select between the
Engine Start mode.
OFF  When the switch is in this position
BOOST or CHARGE/MAINTAIN  When the
button can be set to either the Charge/
Maintain 6A<>2A or the Boost 35A setting.
ENGINE START  When the switch is in this
RATE SELECTION BUTTON
CHARGE/MAINTAIN A2A For
charging small and large batteries. Not
recommended for industrial applications.
BOOST 35A  This setting should only be
Start function. Do not use this setting to
charge your battery.
ENGINE START 2A  Provides 200
run-down battery. Always use in combination
with a battery.
LED INDICATORS
CLAMPS REVERSED (red) LED
The connections are reversed.
CHARGING (yellow) LED lit:
The charger is charging the battery.
The charger is in abort mode.
CHARGED/MAINTAINING (green)
LED pulsing: The battery is fully charged
and the charger is in maintain mode.
NOTE: See the Operating Instructions
section for a complete description of the
charger modes.
OPERATING INSTRUCTIONS
WARNING:
cause battery explosion.
CHARGING A BATTERY IN THE VEHICLE
1. Turn off all the vehicles accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Set the switch to the OFF position.
5. Lay the AC/DC cables away from any fan
parts that can cause injury.
6. For a negative-ground vehicle (as in
POSITIVE (RED) clamp to the POSITIVE
the chargers NEGATIVE BLACK clamp
away from the battery.
7. the chargers NEGATIVE BLACK
POSITIVE RED clamp to the vehicles
battery. NEVER connect any clamps to
body parts.
8. Connect the charger to an electrical outlet.

6
9. With the charger plugged in and
set the switch to the Boost or Charge/
Maintain position.
10. Select the desired rate.
11.
then remove the clamp from the battery
terminal.
CHARGING A BATTERY
OUTSIDE OF THE VEHICLE
1.
2. Set the switch to the OFF position.
3. Clean the battery terminals.
4. insulated battery cable to the NEGATIVE
cable) (not provided).
5. Connect the POSITIVE (RED) charger
battery post.
6. Position yourself and the negative post
extension cable as far away from the
NEGATIVE (BLACK) charger clamp to
the cables free end.
7. Connect the charger to the electrical outlet.
8. With the charger plugged in and connected
to the Boost or Charge/Maintain position.
9. Select the desired rate.
10.
the positive clamp.
11. A marine (boat) battery must be removed
and charged on shore.
USING THE ENGINE START FEATURE
Your battery charger can be used to jump
start your car if the battery is low. Follow all
safety instructions and precautions for
charging your battery. Wear complete eye
protection and protective clothing.
WARNING: Using the ENGINE START
feature WITHOUT a battery installed in the
vehicle will damage the vehicles electrical
system.
NOTE: If you have charged the battery and
vehicles electrical system. Have the battery
1. Set the switch to the OFF position.
2. With the charger unplugged from the
battery following the instructions given
in the CHARGING A BATTERY IN THE
VEHICLE section.
3. Plug the charger AC power cord into the
AC outlet.
4. With the charger plugged in and
set the ON/OFF switch to the Engine
Start position. The Engine Start LED will
illuminate.
5. seconds pass. If the engine does not
again. This allows the charger and battery
to cool down.
NOTE:
6. 35A Boost rate for 5 minutes before
7. to the OFF position and unplug the AC
power cord before disconnecting the
battery clips from the vehicle.
8. Clean and store the charger in a dry
location.
NOTE: If the engine does turn over but
starting system; there is a problem
somewhere else with the vehicle. STOP
has been diagnosed and corrected.
AUTOMATIC CHARGING MODE
the charger switches to the maintain mode
automatically after the battery is charged.
ABORTED CHARGE
the chargers output is shut off and the
CHARGING
DESULFATION MODE
CHARGING (yellow) LED
COMPLETION OF CHARGE
Charge completion is indicated by the
CHARGED/MAINTAINING (green)
LED. When
switched to the maintain mode of operation.

7
MAINTAIN MODE
(FLOAT-MODE MONITORING)
When the CHARGED/MAINTAINING
delivering a small current when necessary. If
the charger has to provide its maximum
maintain current for a continuous 12 hour
Charge section). This is usually caused by a
drain on the battery or the battery could be
MAINTAINING A BATTERY
The SE-2352-CA charges and maintains 12
NOTE: The maintain mode technology
allows you to safely charge and maintain a
healthy battery for extended periods of time.
connections or other unanticipated conditions
could cause excessive current draws. As
MAINTENANCE AND CARE
Clean the clamps each time you are
that may have come in contact with the
clamps to prevent corrosion.
Occasionally cleaning the case of the
shiny and help prevent corrosion.
Coil the input and output cords neatly when
storing the charger. This will help prevent
accidental damage to the cords and charger.
Store the charger unplugged from the AC
power outlet in an upright position.
the cables.
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE REASON/SOLUTION
Charger will not turn
on when properly
connected.
AC outlet is dead.
Poor electrical connection.
Battery is defective.
Three LEDs come on for The charger is plugged into an
AC outlet. No problem; this is normal.
Engine start does Drawing more than 200 amps.
Failure to wait 3 minutes (180
The charger may be
overheated.
Battery may be severely
discharged.
amount of current drawn. If
than 5 seconds.
When the Engine Start LED
The thermal protector may have
tripped and needs a little longer
try again.
use the 35A Boost rate for 10 to 15